55.140 粗腰桶、桶、筒等 标准查询与下载

T/CPF 0066-2023 质量分级及“领跑者”评价要求 铝易开盖三片罐

本文件规定了铝易开盖三片罐产品质量及企业标准水平的基本要求、评价指标及要求、评价方法及等级划分和产品质量分级。

Assessment requirements for quality grading and forerunner— Three-piece can with aluminum easy open end

ASTM F3429/F3429M-23 安装在一次性和预装易燃液体容器中的火焰缓解装置性能的标准规范

1.1  This specification establishes performance requirements for the performance of flame mitigation devices (FMDs) installed in disposable and pre-filled liquid containers, intended for consumer use where the liquid flashpoint is below 60 ºC [140 ºF]. 1.1.1  Uses of disposable and pre-filled flammable liquid containers include but are not limited to fuels, fire starters, and additives for internal combustion engines. 1.1.2  An FMD that complies with this specification minimizes the potential of flame jetting or container rupture from occurring. 1.1.3  Containers without a significant area reduction at the container opening are not covered because there is no hazard of a flame jet or container rupture because an internal pressure rise does not result from an internal ignition. (See Appendix X1 .) 1.2  This specification does not apply to the following containers: 1.2.1  Containers greater than 20 L [5.3 gal] or smaller than 100 mL [3.4 oz] in volume. 1.2.2  Containers intended for beverages. 1.2.3  Portable fuel containers as defined in Specification F852/F852M . 1.2.4  One-time use portable emergency fuel containers for use by consumers as defined in Specification F2874 . 1.2.5  Containers not intended to be open to ambient conditions such as those for liquefied petroleum gas. 1.3  The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Information on specific hazards associated with the test methods in this specification is shown in Section 4.4 . 1.5  This specification does not address hazards caused by fire and explosion nor hazards from vapors external to the container when the fuel in the container does not ignite. Further, this specification does not consider scenarios where confinement, obstructions, or preheating cause flame acceleration prior to the flame front reaching the interior of the container. 1.6  This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of the materials, products, or assemblies under actual fire conditions. 1.7  Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.8  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Performance of Flame Mitigation Devices Installed in Disposable and Pre-Filled Flammable Liquid Containers

T/QGCML 814-2023 锥形开口桶

本标准规定了锥形开口桶的术语定义、结构与尺寸、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于锥形开口桶的制造和检验。

tapered barrel

T/QGCML 813-2023 直身开口钢桶

本标准规定了直身开口钢桶的术语定义、结构与尺寸、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准规定了直身开口桶的制造与检验。

straight open steel drum

T/CAS ES160104001-2022 工业品质量分级评价规则 钢制包装用桶

1　范围 本文件规定了钢制包装用桶（以下简称钢桶）质量分级的评价程序和要求、评价方法、质量分级等内容。 本文件适用于GB/T 325.2、GB/T 325.3范围内钢桶质量分级评价活动。 2　规范性引用文件 下列文件中的内容通过文中的规范性引用而构成本文件必不可少的条款。其中，注日期的引用文件，仅该日期对应的版本适用于本文件；不注日期的引用文件，其最新版本（包括所有的修改单）适用于本文件。 GB/T 325.1  包装容器 钢桶 第1部分：通用技术要求 GB/T 325.2  包装容器 钢桶 第2部分：最小总容量208L、210L和216.5L全开口钢桶 GB/T 325.3  包装容器 钢桶 第3部分：最小总容量212L、216.5L和230L闭口钢桶 GB/T 4857.5  包装 运输包装件 第5部分：跌落试验方法 GB/T 9286  色漆和清漆 划格试验 GB/T 17344  包装 包装容器 气密试验方法 GB/T 19001—2016  质量管理体系 要求 GB/T 24001—2016  环境管理体系 要求及使用指南 GB/T 45001—2020  职业健康安全管理体系 要求及使用指南 T/CAS ES000000001—2022（V01） 工业品质量分级评价规则 通则

Rules for quality grading and evaluating of industrial products—Steel drums for packing containers

ASTM D5571-22 额定容量不超过60Gal（227L）的塑料密封头卷筒耐环境应力开裂性（ESCR）的标准试验方法

1.1 This test method provides an indication of the environmental stress crack resistance of plastic tight-head drums as a summation of the effects of container design, resin, manufacturing conditions, field performance, and other factors. 1.2 This test method may be used to evaluate a plastic drum’s resistance to failure by cracking when in the presence of chemical and physical stresses. 1.3 Two procedures are provided as follows: 1.3.1 Procedure A—Internal pressure stress crack resistance method to nonyl phenoxypoly (ethyleneoxy) ethanol solution, a stress cracking reagent. The internal pressure is controlled at a constant elevated pressure and temperature. 1.3.2 Procedure B—Top-load stress crack resistance method to nonyl phenoxypoly ethanol, a stress cracking reagent. The compressive top-load is controlled at a constant weight while maintaining an elevated temperature. 1.4 Although these procedures are not designed to test the ability of the closure or closure gasket material to retain the test reagent, the inclusion of closure failure as a container failure mode is optional. However, leakage through a closure may affect the internal pressure that could affect the test results. 1.5 This test method does not attempt to address all factors that could lead to stress cracking of plastic drums. The user of this standard may use other test parameters, such as top-loads, chemical reagents, etc., as agreed upon between the user and supplier in the event of a drum qualification or purchase agreement. 1.6 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in 6.2. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Environmental Stress Crack Resistance (ESCR) of Plastic Tight-head Drums Not Exceeding 60 Gal (227 L) in Rated Capacity

KS T 1078-2022 钢桶用堵头和法兰

Plugs and flanges for steel drums

EN ISO 15750-3:2022 包装.钢制鼓形桶.第3部分:插入式法兰型密封系统

This document specifies the characteristics, dimensions and finish of the inserted flange-type closure systems used for steel drums.

Packaging - Steel drums - Part 3: Inserted flange-type closure systems (ISO 15750-3:2022)

BS EN ISO 15750-3:2022 包装 钢铁鼓 插入式法兰型封闭系统

1   ​Scope This document specifies the characteristics, dimensions and finish of the inserted flange-type closure systems used for steel drums.

Packaging. Steel drums. Inserted flange-type closure systems

ASTM F3304-22 灯燃料和火炬燃料包装的标准规范

1.1 This specification is intended to set forth the packaging requirements for lamp fuel and torch fuel intended for use by consumers in and around the household and which contain 10 % or more petroleum distillates with a viscosity of less than 100 SUS (Saybolt universal viscosity) at 100 °F. 1.2 The specification is not intended to cover materials defined as flammable or extremely flammable. 1.3 This packaging specification is intended to set forth design and performance requirements related to packaging, closures, and product labeling. 1.4 This specification applies to pourable lamp fuel and torch fuel containers with a rated capacity of less than 5 gal intended for household use. 1.5 Exemptions—Products defined as a pesticide by the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA) are exempt from Section 5.1 labeling requirements. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Lamp Fuel and Torch Fuel Packaging

ISO 15750-3:2022 包装.钢桶.第3部分:插入法兰式封闭系统

This document specifies the characteristics, dimensions and finish of the inserted flange-type closure s ys tems used for s teel drums.

Packaging — Steel drums — Part 3: Inserted flange-type closure systems

CAN/CGSB-43.146-2022 危险货物运输中型散装集装箱的设计、制造和使用 第3、4、5、6.1、8和9类

1.1 Organization and content This standard sets out requirements for designing, manufacturing and marking of Intermediate Bulk Containers (IBCs) and for selecting and using means of containment for the transportation of dangerous goods of Classes 3, 4, 5, 6.1, 8 and 9. This standard consists of two parts and five annexes. Part I contains the requirements for the design, manufacture and marking of UN standardized IBCs. Part II contains the requirements for the selection and use of means of containment for the transportation of dangerous goods of Classes 3, 4, 5, 6.1, 8 and 9. Annex A sets out the minimum requirements for the completion of a UN standardized IBC design type report submitted to the Director. Annex B, Part 1 contains a list of packing instruction numbers for dangerous goods. Annex B, Part 2 contains the detailed packing instruction information. Annex C contains the periodic leak test and inspection registration process and requirements. Annex D contains a table that provides examples of maximum vapour pressures for liquid dangerous goods transported in specified IBC design types. Annex E contains guidance for minimum venting capacity for metal IBCs used for transporting liquids. Note: Requirements on the packaging, handling, offering for transport and transport of explosives (Class 1) may be found in CAN/CGSB-43.151. 1.2 Application This standard applies to both standardized and non-standardized means of containment as defined in the TDG Regulations. 1.3 Minimum requirements This standard sets out certain minimum requirements regarding the design, construction, qualification, selection and use and testing of means of containment. It is essential to exercise competent technical and engineering judgment in conjunction with this standard. It is the responsibility of the IBC manufacturer to ensure that the IBC will safely carry out its intended function within these constraints. 1.4 Transportation of Dangerous Goods Act and Regulations prevalence The Transportation of Dangerous Goods Act (TDG Act), 1992 and the Transportation of Dangerous Goods Regulations (TDG Regulations) may call for additional requirements regarding the design, construction, qualification, selection, use, and testing of means of containment. Where there is an inconsistency between the requirements of this standard and those of the TDG Act or TDG Regulations, the Act or Regulations prevail to the extent of the inconsistency. regulatory authority. It is recommended to read the standard in conjunction with the TDG Regulations. 1.5 Safety The testing and evaluation of a product against this standard may require the use of materials and/or equipment that could be hazardous. This document does not purport to address all the safety aspects associated with its use. Anyone using this standard has the responsibility to consult the appropriate authorities and to establish appropriate health and safety practices in conjunction with any applicable regulatory requirements prior to its use. 1.6 Units Quantities and dimensions used in this standard are given in metric units from the International System of Units (SI units). Note: Both °B (indicating Baumé scale) and USC units (indicating United States customary units) are used in the standard. SI or metric units are not available for these measurements. 1.7 Classification Dangerous goods are classified in accordance with Part 2 of the TDG Regulations and the appropriate UN number, shipping name and description, class, packing group/category, as applicable, are assigned.

Design, manufacture and use of intermediate bulk containers for the transportation of dangerous goods, Classes 3, 4, 5, 6.1, 8 and 9

ASTM F852/F852M-22 消费者用便携式汽油、煤油和柴油容器的标准规范

1.1 This specification establishes performance requirements for portable gasoline, kerosene, and diesel containers intended for reuse by the consumer. This specification also covers reusable containers for gas/oil mixtures commonly used for two-cycle engines and reusable dual-compartment containers for separate gas and oil storage. 1.2 This specification is not a fire hazard standard, but a specification for portable gasoline, kerosene, and diesel containers for consumer use. 1.3 This specification defines performance requirements for systems that can effectively reduce fuel spillage and emissions when used in accordance with the manufacturer’s (marked) warnings, operating instructions, and limitations of use. This specification does not provide assurance that systems meeting the requirements are suited to all fueling applications and conditions. 1.4 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems has the potential to result in non-conformance with the standard. 1.5 The following precautionary caveat applies only to the Test Method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Section 6 for additional precautionary information. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Portable Gasoline, Kerosene, and Diesel Containers for Consumer Use

ASTM F670-02(2022) 5和10加仑（20和40升）润滑油分配槽的标准规范

1.1 This specification covers the material, dimensions, and construction of 5 and 10-gal (20 and 40-L) tanks purchased to store and dispense lubricating oils. The tanks are industrial safety cans mounted on a T-bar bracket, complete with drip tray. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Tanks, 5 and 10-Gal (20 and 40-L) Lube Oil Dispensing

ASTM F3326-21 便携式燃料容器上火焰缓解装置的标准规范

1.1 This specification establishes performance requirements for flame mitigation devices (FMDs) in portable fuel containers (PFCs) for gasoline, kerosene, and diesel fuels intended for reuse by the consumer. 1.2 A flame mitigation device in gasoline (red), diesel (yellow), and kerosene (blue) PFCs protects the container openings from possible propagation of a flame into a flammable fuel-air mixture within the container. Formation of a flammable fuel-air mixture in the container can occur in special circumstances associated with cold ambient conditions and low liquid levels in the container. Delineations of those circumstances and conditions have been described in published reports, for example, Gardiner et al, 2010 (1),2 and papers, for example, Elias et al, 2013 (2), including research sponsored and overseen by the ASTM F15.10 Technical Committee. 1.3 This specification does not address the hazard of injury or death caused by ignition of vapors external to the PFC when the fuel in the PFC is poured onto or near to a fire or other ignition source causing these external vapors to ignite or explode. An FMD does not prevent hazards associated with misuse of the PFC resulting in external vapor ignition. 1.4 The flame mitigation device is chemically conditioned by exposure to representative fuel surrogates CE25a and CE85a fuel and other expected conditions prior to the tests. 1.5 The flame mitigation device is mechanically conditioned by repeated insertions and removal of a fuel refueling spout prior to the tests. 1.6 The first test method establishes that the flame mitigation device can effectively prevent flame propagation into a flammable butane-air mixture inside the portable fuel container. The butane-air mixture is a controlled and repeatable proxy for the more variable fuel vapor-air mixture in the container. 1.7 The second test method establishes that the flame mitigation device is permitting adequate flow rates of fuel. 1.8 This specification states values in SI units which are to be regarded as the standard. The values given in parentheses are for information only. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Flame Mitigation Devices on Portable Fuel Containers

prEN ISO 15750-3:2021 包装 钢桶 第3部分：插入式法兰式封闭系统（ISO/DIS 15750-3:2021）

Packaging - Steel drums - Part 3: Inserted flange-type closure systems (ISO/DIS 15750-3:2021)

T/ZZB 2331-2021 铁质气雾普通罐

本文件规定了铁质普通气雾罐的术语和定义、规格、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本文件适用于内口径为25.4 mm、 容积不大于1 000 mL、 用镀锡(铬)薄钢板制成的普通三片气雾罐（以下简称“气雾罐”）。 本文件不适用于盛装食品、药品、化妆品的气雾罐。

Ordinary tinplate aerosol can

ASTM D5743-21 在桶或类似容器中采样有或没有固体的单层或多层液体的标准实践

1.1?This practice covers typical equipment and methods for collecting samples of single or multilayered liquids, with or without solids, in drums or similar containers. These methods are adapted specifically for sampling drums having a volume of 110 gal (416 L) or less. These me

Standard Practice for Sampling Single or Multilayered Liquids, with or Without Solids, in Drums or Similar Containers

KS T 1077-2020 全可拆卸头钢桶

Full removable head steel drums

KS T ISO 15750-3-2020 用于钢桶的插入式法兰式封闭系统

Inserted flange-type closure systems used for steel drum