61.040 帽子、服饰品、衣扣 标准查询与下载

ASTM D5171-15 塑料线缝纽扣抗冲击性的标准试验方法

5.1 This test method may be used to determine the ability of a button to resist breaking under impact, for example in pressing the end item, which could cause the button to fail. Note 1: In the development of this test method it was found that the following factors influenced the ability of a button to resist failure under impact conditions: resin formulation, shape ligne size, thickness, number and spacing of holes. Buttons may also pass this test but fail during the pressing of a garment due to the presence of heat during pressing. 5.1.1 If there are differences of practical significance between the reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate rest results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. 5.2 Test Method D5171 for the determination of the impact resistance of buttons may be used for acceptance testing of commercial shipments of buttons but caution is advisable since information is lacking on precision. 1.1 This test method covers the determination of impact resistance of plastic sew-through buttons. 1.2 The values stated in either acceptable metric units or other units shall be regarded separately as standard. The values expressed in each system may or may not be exact equivalents: therefore, each system must be used independently of the other, without combining values in any way. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Impact Resistance of Plastic Sew-Through Buttons

GOST 33378-2015 针织帽. 通用规格

Knitted hats. General specifications

KS K 5101-2014 工作手套

Working gloves

KS K 0833-2014 快速腐蚀试验方法

Test method for snap corrosion

KS G 3711-2014 雨伞

Umbrellas

QB/T 2171-2014 金属拉链

本标准规定了金属拉链的术语和定义、分类、要求、测试条件、试验方法、检验规则和标志、包装、运输、贮存、使用准则。本标准适用于金属拉链(以下简称“拉链”),不适用于特种拉链。

Metal zipper

QB/T 2172-2014 注塑拉链

本标准规定了注塑拉链的术语和定义、分类、要求、测试条件、试验方法、检验规则和标志、包装、运输、贮存、使用准则。本标准适用于注塑拉链(以下简称拉链),不适用于特种拉链。

Derlin zipper

QB/T 2173-2014 尼龙拉链

本标准规定了尼龙拉链的术语和定义、分类、要求、测试条件、试验方法、检验规则和标志、包装、运输、贮存、使用准则。本标准适用于尼龙拉链(以下简称“拉链”),不适用于特种拉链。

Nylon zipper

GOST 32118-2013 头饰. 通用技术条件

Headgears. General technical conditions

QB/T 4662-2014 编织帽

本标准规定了编织帽的要求、试验方法、检验规则和标志、包装、运输、贮存。本标准适用于以木纤维工艺编织纸为原料生产加工而成的编织帽;以天然草(金丝草、麻草、水草、玉米皮、亚菲草、麦草、通芯草等)、天然扁平粘胶纤维为原料生产加工而成的编织帽可参照执行。

Knitting hat

SB/T 11055-2013 皮帽采购验收规范

本标准规定了皮帽的要求、检验方法、检验规则及有关标志、包装、运输和储存的要求。本标准适用于以毛皮或皮革为主要原料的皮帽采购验收。

Procurement and acceptance standard for fur and leather hats

ASTM D4035-14 针织领和围巾面料的标准性能规格

5.1 Upon mutual agreement between the purchaser and the seller, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification. 5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the seller. 5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4035 except for the following characteristic(s).” 5.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric. 5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods. 1.1 This performance specification covers knitted necktie and scarf fabrics composed of any textile fiber or mixture of textile fibers. 1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent. 1.3 The following precautionary statement pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Performance Specification for Knitted Necktie and Scarf Fabrics

ASTM D2058-03(2014) 拉链表面处理耐磨性的标准试验方法

1.1 This test method covers the determination of the durability of the enamel or other decorative coating of zippers when subjected to drycleaning. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Durability of Finish of Zippers to Drycleaning

GOST 9441-2014 全羊毛混纺披巾, 围巾和披肩. 通用规格

All wool and blended shawls, scarfs and palatines. General specifications

GOST 5274-2014 针织围巾和披巾. 通用规格

Knitted scarfes and shawls. General specifications

QB/T 4560-2013 六片运动帽

本标准规定了六片运动帽的结构与命名、分类、要求、试验方法、检验规则和标志、包装、运输、贮存。本标准适用于以棉、毛、麻、丝、化纤及其各种混纺织物为原料生产的,具有体育运动、遮阳、保暖、装饰等作用的六片运动帽。本标准也适用于以六片运动帽(以下简称“运动帽”)为基础延伸的片式拼接帽。

Six pieces sport caps

KS G 3124-2013 按扣

Snap buttons

KS G 3112-2013 双管状铆钉或皮革纽扣

Double tubular rivets or leather buttons

DB15/T 561-2013 鄂伦春民族服饰

Oroqen National Costumes

DB15/T 562.3-2013 鄂温克民族服饰 第3部分 通古斯鄂温克服饰

Ewenki National Costumes Part 3 Tungus Ewenki Costumes