77.020 金属生产 标准查询与下载

T/SHDSGY 027-2023 柔性石墨金属缠绕垫片

本文件规定了柔性石墨金属缠绕垫片的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于各种介质的管法兰、压力容器法兰、摩托车、汽车排气管静密封的柔性石墨金属缠绕垫片。

Flexible graphite metal wound gasket

T/CNIA 0191-2023 铜矿石生物堆浸循环过程控制技术规范

本文件规定了铜矿石生物堆浸循环过程控制的设备要求、生产工艺要求及生物堆浸过程取样和检测要求。 本文件适用于可溶性钙镁总含量（质量分数）不大于15%的氧硫混合铜矿石及硫化铜矿石生物堆浸生产。

Technical Specification for Copper Ore Bioheap Leaching Cycle Process Control

ASTM E1476-04(2022) 金属识别、等级验证和分类的标准指南

1.1 This guide is intended for tutorial purposes only. It describes the general requirements, methods, and procedures for the nondestructive identification and sorting of metals. 1.2 It provides guidelines for the selection and use of methods suited to the requirements of particular metals sorting or identification problems. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 10. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Metals Identification, Grade Verification, and Sorting

T/SGZX 008-2022 固定式火焰熔铝炉节能控制系统技术要求

本文件规定了固定式火焰熔铝炉节能控制系统的组成、基本要求及控制、功能、通信、性能等技术要求。

Technical requirements for energy-saving control system of fixed flame aluminium melting furnace

T/CIECCPA 015-2022 钢铁低碳烧结技术规范

本文件规定了钢铁行业低碳烧结技术相关的术语和定义、技术要求、测试和计算方法。 本文件适用于钢铁行业低碳烧结技术的选择和运行管理。

Technical specification for low carbon sintering of iron and steel

YB/T 6050-2022 冶金焦化、烧结、球团配料自动采样控制系统技术规范

本文件规定了焦化配煤、烧结矿配料、球团矿配料过程自动采样控制系统的集成系统基本要求、采样单元基本要求、制样单元基本要求和控制单元基本要求。 本文件适用于焦化配煤生产线、烧结矿配料、球团矿配料生产线。

Technical specifications for automatic sampling control system for metallurgical coking, sintering and pellet batching

ASTM D6558-22 测定焙烧碳阳极和阴极块的热重分析CO反应性的标准试验方法

1.1 This test method covers the thermogravimetric (TGA) determination of CO2 reactivity and dusting of shaped carbon anodes and cathode blocks used in the aluminum reduction industry. The apparatus selection covers a significant variety of types with various thermal conditions, sample size capability, materials of construction, and procedures for determining the mass loss and subsequent rate of reaction. This test method standardizes the variables of sample shape, reaction temperature, gas velocity over the exposed surfaces, and reaction time such that results obtained on different apparatuses are correlatable. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of TGA CO2 Reactivity of Baked Carbon Anodes and Cathode Blocks

ASTM D6559-22 测定焙烧碳阳极和阴极块的热重（TGA）空气反应性的标准试验方法

1.1 This test method covers the thermogravimetric (TGA) determination of air reactivity and dusting of shaped carbon anodes and cathode blocks used in the aluminum reduction industry. The apparatus selection covers a significant variety of types with various thermal conditions, sample size capability, materials of construction, and procedures for determining the mass loss and subsequent rate of reaction. This test method standardizes the variables of sample shape, reaction temperature, gas velocity over the exposed surfaces, and reaction time such that results obtained on different apparatuses are correlatable. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Thermogravimetric (TGA) Air Reactivity of Baked Carbon Anodes and Cathode Blocks

T/CNIA 0131-2022 锌湿法冶炼中镓铟锗同步富集技术规范

本文件规定了锌湿法冶炼过程中镓铟锗同步富集技术的总体要求、设备要求、工艺流程、质量要求和运行与管理。 本文件适用于锌湿法冶炼过程中镓铟锗的同步富集，供生产镓、铟、锗等元素的化学品及金属制品等。

Technical specifications for simultaneous enrichment of gallium, indium and germanium in zinc hydrometallurgy

T/CISA 168-2021 用于制备还原铁粉的氧化铁皮技术规范

本标准规定了还原铁粉用氧化铁皮技术规范的术语和定义、基本原则、一般要求、工艺流程、检验规则和包装、标志、运输、贮存及质量证明书。 本标准适用于环保、冶金、机械等行业的氧化铁皮制备还原铁粉。

Technical specification for iron oxide scale for preparation of reduced iron powder

T/QYZL 32-2021 非建筑用铝合金装饰型材

非建筑用铝合金装饰型材的要求、试验方法、检验规则和标志、包装、运输、贮存及质量证明书

Aluminium alloy extruded profiles used for decoration excluding architecture

T/CSCP 0001-2022 钢筋混凝土用钢-耐蚀热轧带肋钢筋

本标准规定了钢筋混凝土用钢-耐蚀热轧带肋钢筋耐蚀性能的术语和定义、分类、牌号、订货内容、尺寸、外形、重量及允许偏差、技术要求、试验方法、检验规则、包装、标志和质量证书等。本标准适用于评价符合 GB/T 1499.2-2018 的各牌号钢在内陆自然环境和海洋环境下服役的耐蚀性能。

Steel for reinforced concrete - Corrosion-resistant hot-rolled ribbed steel bar

T/CNS 50.3-2021 核电厂用奥氏体不锈钢构筑成形工艺技术要求　第3部分：锻造加热

本文件规定了采用金属构筑成形工艺生产的316H奥氏体不锈钢构筑坯锻造加热技术要求。

Additive forging technique applied to austenitic stainless steel used in nuclear power plant - part 3: Heating for forging

T/CNIA 0105-2021 氧化铝生产过程中草酸根离子含量的测定 离子色谱法

本文件规定了氧化铝生产过程中草酸根离子含量的测定方法。 本文件适用于氧化铝生产过程中草酸根离子含量的测定。液体试料测定范围为：0.50?g/L～15.00?g/L，固体试料测定范围为：0.050%～3.00%。

Determination of Oxalate Ion Content in Alumina Production Process by Ion Chromatography

T/CRIA 26002-2021 钢帘线粘合试验用标准胶

4.胶料配方 5.胶料混炼工艺 6.要求 6.1胶料要求 6.2 原料要求 7.胶料的运输和储存 8.胶料的使用

Standard glue for steel cord adhesion test

YB/T 4803-2020 4000立方米及以上高炉入炉原燃料技术要求

Technical requirements for raw fuel input into blast furnaces of 4,000 cubic meters and above

T/CSRE 19001-2020 金属镱靶材

本文件规定了金属镱靶材的要求、试验方法、检验规则和标志、包装、运输、贮存质量证明书。 本文件适用于真空熔炼法生产的金属镱靶材。主要作为有机发光材料（OLED）金属镀层的蒸发材料。

Metal Ytterbium Target

T/CFA 030501-2020 铸造企业生产能力核算方法

本文件规定了铸造企业生产能力核算的术语和定义、核算原则、核算项目、核算方法。  

Accounting method of production capacity for foundry

T/GAMA 12-2020 增材制造 金属粉末床熔融成型工艺过程控制与要求

规定了金属粉末床熔融成型成型工艺原材料和粉末批次、人员需求、系统软件和数据配置的控制、辅助工具和污染、外部环境控制、生产计划、成型前的检查、定期保养和机器、工艺和零件鉴定，适用于激光束和电子束粉末床熔融成型的零件和机械性能测试样品的制备。

Process control and requirements of metal powder bed fusion forming process for additive manufacturing

T/CSM 8-2020 钢铁行业绿色生产管理评价 第7部分：冷轧

本标准包含钢带宽度≥900mm，厚度≥3mm的冷轧钢带及热浸镀（锌及其他合金）产品的冷轧加工工序（含酸轧、退火、热镀锌加工工序），不含彩涂板、不锈钢、电工钢、电镀锌、电镀锡。本标准不包含锻压、挤压及后续加工工序。

Evaluation of Green Production Management in Iron and Steel Industry Part 7: Cold Rolling