77.020 金属生产 标准查询与下载

T/CWAN 0001-2016 无镀铜焊丝

4.1 焊丝化学成分检验 4.2 熔敷金属力学性能 4.3 焊缝射线探伤 4.4 焊丝尺寸及允许偏差 4.5 焊丝表面质量 4.6焊丝松弛直径和翘距 4.7 熔敷金属扩散氢含量

Non copper-plating welding electrodes and rods

YS/T 1108-2016 锡冶炼安全生产规范

Safety production regulations for tin smelting

DB44/T 1858-2016 城镇排水检查井盖技术规程

安装在绿化带、人行道、非机动车道、机动车道、停车场、码头、机场等地面井盖净开孔(co)不大于900mm的排水管道检查井盖。其他专业（通信、电力等）井盖可参考使用

Technical specification for urban drainage inspection manhole covers

ASTM D6559-00A(2016)e1 烘烤碳阳极和阴极块的热重（TGA）空气反应性测定的标准测试方法

1.1 This test method covers the thermogravimetric (TGA) determination of air reactivity and dusting of shaped carbon anodes and cathode blocks used in the aluminum reduction industry. The apparatus selection covers a significant variety of types with various thermal conditions, sample size capability, materials of construction, and procedures for determining the mass loss and subsequent rate of reaction. This test method standardizes the variables of sample dimensions, reaction temperature, gas velocity over the exposed surfaces, and reaction time such that results obtained on different apparatuses are correlatable. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Thermogravimetric (TGA) Air Reactivity of Baked Carbon Anodes and Cathode Blocks

ASTM D5061-16 冶金焦炭结构部件显微测定的标准试验方法

5.1 The determination of the volume percent of the textural components in coke is useful to characterize the optical properties of coke as it relates to utilization. Specifically, the technique has been used as an aid in determining coal blend proportions, and recognition of features present in the coke that can be responsible for coke quality or production problems such as reduced coke strength or difficulty in removing coke from commercial coke ovens, or both. The study of coke textures is also useful in promoting a better understanding of coke reactivity, and the relationship between coal petrography and its conversion to coke.4 5.2 This test method is used in scientific and industrial research, but not for compliance or referee tests. 1.1 This test method covers the equipment and procedures used for determining the types and amounts of coke carbon forms and associated recognizable coal- and process-derived textural components in metallurgical coke in terms of volume percent. This test method does not include coke structural components such as coke pores, coke wall dimensions, or other structural associations. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Microscopical Determination of the Textural Components of Metallurgical Coke

SAE AS6279-2014 金属材料的生产, 分布以及采购的标准实施规程

This SAE Aerospace Standard (AS) establishes requirements applicable to metal stock that is ordered and produced in accordance with an Aerospace Material Specification (AMS). Topics include producer requirements, distributor requirements, size and grain orientation nomenclature, and purchaser ordering information to distributors. Requirements of this document have been developed to address titanium and titanium alloys.

Standard Practice for Production, Distribution, and Procurement of Metal Stock

KS D ISO 3134-5:2013 轻金属及其合金 术语和定义 第5部分：加工和处理方法

Light metals and their alloys－Terms and definitions－Part 5 : Methods of processing and treatment

YS/T 883-2013 锌精矿焙砂

本标准规定了锌精矿焙砂的要求、试验方法、检验规则、包装、运输和质量预报单以及合同(或订货单)内容、本标准适用于以硫化锌精矿为原料,经焙烧产出的主要供炼锌用锌精矿焙砂、

Zinc concentrate roasting

DB37/T 2266-2013 高炉渣干法处理技术规范

本标准规定了山东省钢铁厂高炉渣干法处理的术语、分类、技术要求、实验方法的技术规范。 本标准适用于对山东省境内的现有钢铁企业及对新建、改建、扩建钢铁企业的高炉渣干法处理工程。

Technical specification for dry treatment of blast furnace slag

SAE J1086-2012 金属和合金编号

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice describes a unified numbering system (UNS) for metals and alloys which have a "commercial standing" and covers the procedure by which such numbers are assigned. Section 2 describes the system of alphanumeric designations or "numbers" established for each family of metals and alloys. Section 3 outlines the organization established for administering the system. Section 4 describes the procedure fo

Numbering Metals and Alloys

DB51/T 1429-2012 铸铁锅生产技术规范

Technical specifications for the production of cast iron pans

YS/T 784-2012 铝电解槽技术参数测量方法

本标准规定了铝电解槽技术参数的测量方法。 本标准适用于预焙阳极电解槽技术参数的测量。

Measurement of technical parameter for aluminium cell

ASTM D6354-12(2017) 铝生产用炭阴极块的取样计划和芯取样的标准指南

4.1 Core sampling is an acceptable way of obtaining a test specimen without destroying the usefulness of a cathode block. 4.1.1 Test specimens obtained by this guide can be used by producers and users of cathode blocks for the purpose of conducting the tests in Note 1 to obtain comparative physical properties. 4.2 Sampling shall not weaken the cathode block or increase the likelihood of premature failure. Extreme care shall be exercised when taking vertically drilled samples. 1.1 This guide covers sampling of carbon cathode blocks used in the production of aluminum, and details procedures for taking samples from single cathode blocks. It covers equipment and procedures for obtaining samples from cathode blocks in a manner that does not destroy the cathode block or prevent its subsequent use as originally intended. However, the user must determine the subsequent use of the sampled cathode blocks. Preferred locations for taking samples from single units of cathode blocks are covered in this guide. 1.1.1 Information for sampling of shaped refractory products, in general, is given in ISO8201;5022. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot. Cathode blocks used in the production of aluminum have specific requirements of sampling, and while the statistical basis for sampling given in ISO8201;5022 applies, further or modified requirements may also apply. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 1: The following ASTM standards are noted as sources of useful information: Test Methods C559, C611, C651, C747, C1025, C1039, and C1225. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Sampling Plan and Core Sampling of Carbon Cathode Blocks Used in Aluminum Production

YS/T 758-2011 铝用炭素回转窑直线度测量方法

本标准规定了铝用碳素回转窑日常生产过程中直线度的测量方法。 本标准适用于铝用碳酸回转窑直线度的测量。回转窑直径≥2.2m,长度≥45m,支撑点在两组以上。

Straightness measuring method of rotary kiln for aluminium-carbon

DB43/T 578-2010 锑冶炼砷碱渣无害化处理技术规范

Technical specification for harmless treatment of arsenic-alkali slag from antimony smelting

DB43/T 579-2010 铋冶炼污染控制技术规范

Technical specification for pollution control of bismuth smelting

ASTM D5061-07 冶金焦炭结构成分显微镜测定的标准测试方法

The determination of the volume percent of the textural components in coke is useful to characterize the optical properties of coke as it relates to utilization. Specifically, the technique has been used as an aid in determining coal blend proportions (after correcting for coke yield), and recognition of features present in the coke that can be responsible for coke quality or production problems such as reduced coke strength or difficulty in removing coke from commercial coke ovens, or both. The study of coke textures is also useful in promoting a better understanding of coke reactivity, and the relationship between coal petrography and its conversion to coke.4 This test method is used in scientific and industrial research, but not for compliance or referee tests.1.1 This test method covers the equipment and procedures used for determining the types and amounts of coke carbon forms and associated recognizable coal- and process-derived textural components in metallurgical coke in terms of volume percent. This test method does not include coke structural components such as coke pores, coke wall dimensions, or other structural associations.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Microscopical Determination of the Textural Components of Metallurgical Coke

ASTM D6353-06(2017)e1 铝生产用预焙阳极的取样计划和芯取样的标准指南

4.1 Core sampling is an acceptable way of obtaining a test specimen without destroying the usefulness of an anode block. 4.1.1 Test specimen obtained by this guide can be used by producers and users of carbon anodes for the purpose of conducting the tests in Note 1 to obtain comparative physical properties. 4.2 Sampling shall not weaken the anode or increase the likelihood of premature failure. 1.1 This guide covers sampling for prebaked carbon anodes used in the production of aluminum, and details procedures for taking test samples from anode blocks. It covers equipment and procedures for obtaining samples from anode blocks in a manner that does not destroy the block or prevent its subsequent use as originally intended. However, the user must determine the subsequent use of the sampled anode blocks. Preferred locations for taking samples from single units of anodes are covered in this guide. 1.1.1 Information for sampling of shaped refractory products, in general, is given in ISO8201;5022. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot. Anodes used in the production of aluminum have specific requirements for sampling and while the statistical basis for sampling given in ISO8201;5022 applies, further or modified requirements may also apply. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1: The following ASTM standards are noted as sources of useful information: Test Methods C559, C611, C651, C747, C1025, C1039, and E1225.

Standard Guide for Sampling Plan and Core Sampling for Prebaked Anodes Used in Aluminum Production

ASME B32.100-2005 扁平、圆形、正方形、矩形和六角形金属制品的首选米制尺寸

This Standard establishes a preferred series of metric thicknesses, widths, and lengths for flat metal products of rectangular cross-section. The thicknesses and widths shown in this Standard are also applicable to base metals that may be coated in later operations. This Standard also establishes a preferred series of metric sizes for round, square, rectangular, and hexagonal metal products.

Preferred Metric Sizes for Flat, Round, Square, Rectangular, and Hexagonal Metal Products

ANSI B32.100-2005 平板、圆形、方形、矩形和六角形金属制品的最佳米制尺寸

Establishes a preferred series of metric thicknesses, a preferred series of metric widths, and a preferred series of metric lengths for flat metal products of rectangular cross section. The thicknesses and widths shown in this Standard are also applicabl

Preferred Metric Sizes for Flat, Round, Square, Rectangle, and Hexagon Metal Products