77.060 金属的腐蚀 标准查询与下载

GB/T 13671-1992 不锈钢缝隙腐蚀电化学试验方法

本标准规定了不锈钢缝隙腐蚀电化学试验方法的原理、试验仪器、试样制备、试验条件、试验步骤和试验报告内容等。 本标准适用于评价不锈钢在氯化物环境中的抗缝隙腐蚀性能，特别适用于不同钢种或不同状态的比较。本标准也适用于评价人体外科植入金属材料的抗缝隙腐蚀性能。

Stainless steels.Method of electrochemical test for crevice corrosion

GB/T 10119-1988 黄铜耐脱锌腐蚀性能的测定

本标准规定了黄铜材料在淡水或海水中耐脱锌腐蚀性能的测定方法。 本标准适用于黄铜材料在淡水或海水中耐脱锌腐蚀性能的测定。 本标准可用于控制和研究的目的，但对使用范围不作规定。

Copper-zinc alloys--Determination of dezincification corrosion resistance

GB 7998-1987 铝合金晶间腐蚀测定方法

The method for determining the intergranular corrosion of aluminium alloy

GB/T 5776-1986 金属材料在表面海水中常规暴露腐蚀试验方法

本标准适用于金属材料（包括黑色、有色金属）在表面海水（海水深度在10m之内）中全浸、潮差及飞溅条件下的腐蚀试验。为海水腐蚀试验应遵循的一般程序，以统一试验条件和评价指标。

Method for surface seawater exposure corrosion tests of metallic materials

ISO 9227:2022/Amd 1:2024

Corrosion tests in artificial atmospheres. Salt spray tests

ISO 10062:2022/Amd.1:2024

Corrosion tests in artificial atmosphere at very low concentrations of polluting gas(es)

ASTM C1617-24 定量加速实验室评价热绝缘材料中浸出离子萃取溶液对碳钢水腐蚀的标准试验方法

1.1  This test method covers procedures for a quantitative accelerated laboratory evaluation of the influence of extraction solutions containing ions leached from thermal insulation on the aqueous corrosion of carbon steel. The primary intent of the practice is for use with thermal insulation and associated materials that contribute to, or alternatively inhibit, the aqueous corrosion of carbon steel due to soluble ions that are leached by water from within the insulation. The quantitative evaluation criteria are Mass Loss Corrosion Rate (MLCR) expressed in mils per year determined from the weight loss due to corrosion of exposed metal coupons after they are cleaned. 1.2  This test method cannot cover all possible field conditions that contribute to aqueous corrosion. The intent is to provide an accelerated means to obtain a non-subjective numeric value for judging the potential contribution to the corrosion of carbon steel that can come from ions contained in thermal insulation materials or other experimental solutions. The calculated numeric value is the mass loss corrosion rate. This calculation is based on general corrosion spread equally over the test duration and the exposed area of the experimental cells created for the test. Corrosion found in field situations and this accelerated test also involves pitting, edge effects, and the rate changes over time. 1.3  The insulation extraction solutions prepared for use in the test can be altered by the addition of corrosive ions to the solutions to simulate contamination from an external source. Ions expected to provide corrosion inhibition can be added to investigate their inhibitory effect. 1.4  Prepared laboratory ionic solutions are used as reference solutions and controls, to provide a means of calibration and comparison.2 1.5  Other liquids can be tested for their potential corrosiveness including cooling tower water, boiler feed, and chemical stocks. Added chemical inhibitors or protective coatings applied to the metal can also be evaluated using the general guidelines of the practice. 1.6  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Quantitative Accelerated Laboratory Evaluation of Extraction Solutions Containing Ions Leached from Thermal Insulation on Aqueous Corrosion of Carbon Steel

24/30462658 DC 人造气氛中的腐蚀试验 加速腐蚀试验包括交替暴露于腐蚀促进气体、中性盐雾和干燥

BS EN ISO 21207 Corrosion tests in artificial atmospheres. Accelerated corrosion tests involving alternate exposure to corrosion-promoting gases, neutral salt-spray and drying

BS EN ISO 11782-2:2008+A1:2024 金属和合金的腐蚀 腐蚀疲劳试验 使用预裂样品进行裂纹扩展试验

Corrosion of metals and alloys. Corrosion fatigue testing - Crack propagation testing using precracked specimens

BS EN ISO 7539-6:2018+A1:2024 金属和合金的腐蚀 应力腐蚀试验 恒定载荷或恒定位移试验中预裂试样的制备和使用

Corrosion of metals and alloys. Stress corrosion testing - Preparation and use of precracked specimens for tests under constant load or constant displacement

ISO 11782-2:1998/Amd 1:2024 金属和合金的腐蚀 腐蚀疲劳试验 使用预裂样品进行裂纹扩展试验

Corrosion of metals and alloys. Corrosion fatigue testing - Crack propagation testing using precracked specimens

ASTM G3-14(2024) 腐蚀试验中适用于电化学测量的惯例的标准实施规程

Standard Practice for Conventions Applicable to Electrochemical Measurements in Corrosion Testing

ASTM G61-86(2024) 铁、镍或钴基合金局部腐蚀敏感性的循环电位极化测量的标准试验方法

Standard Test Method for Conducting Cyclic Potentiodynamic Polarization Measurements for Localized Corrosion Susceptibility of Iron-, Nickel-, or Cobalt-Based Alloys

ASTM D849-15(2024) 工业芳烃对铜带腐蚀的标准试验方法

Standard Test Method for Copper Strip Corrosion by Industrial Aromatic Hydrocarbons

ASTM G71-81(2024) 电解质中进行和评价镀锌腐蚀试验的标准指南

Standard Guide for Conducting and Evaluating Galvanic Corrosion Tests in Electrolytes

GSO ASTM G52:2024 表面海水中金属和合金的暴露和评估标准规范

1.1 This practice covers conditions for the exposure of metals, alloys, and other materials in natural surface seawater such as those typically found in bays, harbors, channels, and so forth,2 as contrasted with deep ocean testing.3 This practice covers full immersion, tidal zone and related splash, and spray zone exposures.2,4 1.2 This practice sets forth general procedures that should be followed in conducting seawater exposure tests so that meaningful comparisons may be made from one location to another. 1.3 This practice identifies recommended procedures for evaluating the effects of natural surface seawater on the materials exposed. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Exposing and Evaluating Metals and Alloys in Surface Seawater

GSO ISO 21207:2024 人工气氛中的腐蚀试验 加速腐蚀试验 包括交替暴露于促进腐蚀的气体、中性盐雾和干燥

ISO 21207:2015 defines two accelerated corrosion test methods to be used in assessing the corrosion resistance of products with metals in environments where there is a significant influence of chloride ions, mainly as sodium chloride from a marine source or by winter road de-icing salt, and of corrosion-promoting gases from industrial or traffic air pollution. ISO 21207:2015 specifies both the test apparatus and test procedures to be used in executing the accelerated corrosion tests. The methods are especially suitable for assessing the corrosion resistance of sensitive products with metals, e.g. electronic components, used in traffic and industrial environments.

Corrosion tests in artificial atmospheres — Accelerated corrosion tests involving alternate exposure to corrosion-promoting gases, neutral salt-spray and drying

T/QGCML 3938-2024 高温抗氧化防脱碳隔离剂

本文件规定了高温抗氧化防脱碳隔离剂的要求、试验方法、检验规则、包装、标志、贮存与运输的内容。 本文件适用于钢材加工过程使用的高温抗氧化防脱碳隔离剂。

High temperature antioxidant and anti-decarburization isolating agent

24/30486175 DC BS EN ISO 8407 AMD 1. 金属和合金的腐蚀 从腐蚀试验样本中去除腐蚀产物

BS EN ISO 8407 AMD 1. Corrosion of metals and alloys. Removal of corrosion products from corrosion test specimens

CAN/CGSB-3.0 No.60.32-2024 石油和相关产品的试验方法用银棉测定汽油、中间馏分燃料和含氧燃料对银的腐蚀性的标准试验方法：快速超声波法

Scope This method provides a means of determining the degree of corrosiveness of gasoline and middle distillate fuels to silver or silver alloys used in fuel system components. This method also applies to oxygenated gasoline and diesel blends, intermediate streams or blending components such as alkylate, reformate, and isomerate. Units of measure — Quantities and dimensions in this standard are given in SI units with imperial equivalents, mostly obtained through soft conversion, given in parentheses. The SI units are regarded as being official in the event of dispute or unforeseen difficulty arising from the conversion. The testing and evaluation of a product against this method may require the use of materials and/or equipment that could be hazardous. This document does not purport to address all the safety aspects associated with its use. Anyone using this method has the responsibility to consult the appropriate authorities and to establish appropriate health and safety practices in conjunction with any applicable regulatory requirements prior to its use.

Methods of testing petroleum and associated products Standard test method for determination of the corrosiveness to silver of gasoline, middle distillate fuels and oxygenated fuels using silver wool: Rapid ultrasonic method