77.150 有色金属产品 标准查询与下载

YS/T 632-2007 黑铜

本标准规定了黑铜的技术要求、试验方法、检验规则、标志、包装、运输、订货单（或合同）内容。 本标准适用于经熔炼处理的废杂铜或铜的氧化物而产生的黑铜。

Low grade blister

ASTM B349/B349M-01 用于核应用的海绵锆和原生金属的其他形式用标准规范

1.1 This specification covers virgin zirconium metal commonly designated as sponge because of its porous, sponge-like texture, but it may also take other forms such as chunklets.1.2 One grade is described which is designated as Reactor Grade R60001, suitable for use in nuclear application. The most important characteristic of the reactor grade is its low nuclear cross section as achieved by removal of hafnium and by careful quality control in manufacturing procedures to prevent contamination with other high cross-section materials.1.3 Unless a single unit is used, for example corrosion mass gain in mg.dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.1.4 The following precautionary caveat pertains only to the test method portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Zirconium Sponge and Other Forms of Virgin Metal for Nuclear Application

YB/T 432-2000 铝塑复合板用铝带

Aluminium strip for aluminium-plastic composite panel

CB/T 102-1996 锡基合金轴瓦铸造技术条件

本标准规定了锡基轴承合金的技术要求、轴瓦基壳的要求、轴瓦的铸造工艺技术要求，以及轴瓦铸造质量的检验。 本标准适用于船用柴油机及船舶轴系衬套等锡荃合金轴瓦的铸造。

Tin-based alloy bearing bush casting technical conditions

YS 72-1994 镉锭

Cadmium ingot

CB 862.2-1988 有色金属锻件技术条件 铜合金模锻件和自由锻件

本标准规定了锻件分类、技术要求、试验方法和验收规则。 本标准适用于军品用铜合金模锻件和自由锻件，民品亦应参照使用。

Technical conditions for non-ferrous metal forgings Copper alloy die forgings and free forgings

CB 862.1-1988 有色金属锻件技术条件 铝合金模锻件和自由锻件

本标准规定了锻件分类、技术要求、试验方法和验收规则。 本标准适用于军品用铝合金模锻件和自由锻件，民品亦应参照使用。

Technical conditions for non-ferrous metal forgings Aluminum alloy die forgings and free forgings

YB 699-1980 铝.锑.镁-钢双金属板

Aluminum. Antimony. Magnesium-steel bimetal plate

YB/T 048-93 钢锭模中稀土棒吊挂方法

Method for hanging rare earth rods in steel ingot mold

YB 699-80 铝.锑.镁-钢双金属板

Aluminum. Antimony. Magnesium-steel bimetal plate

YB/T 036.5-92 冶金设备制造通用技术条件铜合金铸件

General technical conditions for metallurgical equipment manufacturing copper alloy castings

YB/T 036.6-92 冶金设备制造通用技术条件铝合金铸件

General technical conditions for metallurgical equipment manufacturing aluminum alloy castings

YB 523-82 冶金用二氧化钛技术条件

Technical conditions of titanium dioxide for metallurgy

CB/T 3696-1995 有色金属产品物资分类与代码

Classification and codes of non-ferrous metal products