81.060.20 陶瓷制品 标准查询与下载

KS L 1203-2002(2017) 测试方法抗压（压碎）强度焙烧卫生材料的

Testing method for compressive(crushing)strength of fired whiteware materials

ASTM C1161-02c 环境温度下先进陶瓷弯曲强度的标准试验方法

Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature

ASTM C1161-02b 环境温度下先进陶瓷弯曲强度的标准试验方法

Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature

ASTM C1161-02a 环境温度下先进陶瓷弯曲强度的标准试验方法

Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature

KS L 1599-2001 精细陶瓷.单块陶瓷常温、高温抗拉强度试验方法

이 규격은 파인 세라믹스 및 휘스커 강화, 또는 입자 강화 세라믹 복합체의 상온 및 고온에

Fine ceramics(advanced ceramics, advanced technical ceramics)－Test methodfor tensile strength of monolithic ceramics at room and elevated temperature

KS L 1599-2001(2021) 精细陶瓷（高级陶瓷、高级工业陶瓷）－单片陶瓷室温和高温拉伸强度试验方法

Fine ceramics(advanced ceramics, advanced technical ceramics)－Test methodfor tensile strength of monolithic ceramics at room and elevated temperature

KS L 1599-2001(2016) 精细陶瓷（高级陶瓷、高级工业陶瓷）单片陶瓷室温和高温拉伸强度试验方法

Fine ceramics(advanced ceramics, advanced technical ceramics)－Test methodfor tensile strength of monolithic ceramics at room and elevated temperature

ONORM B 8305-2001 瓷砖材料．瓷砖结构构件．要求，试验

Diese ?NORM enth?lt Anforderungen an Kachelmaterial, dessen Prüfung und Kennzeichnung.

Material for tiles - Construction elements of ceramic tiles - Requirements, tests

ONORM B 8304-2001 瓷砖材料．陶瓷炉砖．要求，测试，合格标识

Diese ?NORM enth?lt Anforderungen an keramische Ofenkacheln (in der Folge kurz Ofenkacheln genannt) und deren Prüfungen.

Material for tiles - Ceramic stove tiles - Requirements, tests, marking of conformity

ANSI/ASTM E1876:2001 利用振动的冲击激磁产生动态模量、剪切模量和泊松比的试验方法

This test method covers determination of the dynamic elastic properties of elastic materials at ambient temperatures. Specimens of these materials possess specific mechanical resonant frequencies that are determined by the elastic modulus, mass, and geometry of the test specimen. The dynamic elastic properties of a material can therefore be computed if the geometry, mass, and mechanical resonant frequencies of a suitable (rectangular or cylindrical geometry) test specimen of that material can be measured. Dynamic Young's modulus is determined using the resonant frequency in either the flexural or longitudinal mode of vibration. The dynamic shear modulus, or modulus of rigidity, is found using torsional resonant vibrations. Dynamic Young's modulus and dynamic shear modulus are used to compute Poisson's ratio. Although not specifically described herein, this test method can also be performed at cryogenic and high temperatures with suitable equipment modifications and appropriate modifications to the calculations to compensate for thermal expansion. There are material specific ASTM standards that cover the determination of resonance frequencies and elastic properties of specific materials by sonic resonance or by impulse excitation of vibration. Test Methods C 215, C 623, C 747, C 848, C 1198, and C 1259 may differ from this test method in several areas (for example; sample size, dimensional tolerances, sample preparation). The testing of these materials shall be done in compliance with these material specific standards. Where possible, the procedures, sample specifications and calculations are consistent with these test methods. The values stated in SI units are to be regarded as the standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Test Method for Dynamic Young's Modulus, Shear Modulus and Poisson's Ratio by Impulse Excitation of Vibration

ASTM C949-80(2000) 通过染色渗透法测定玻璃质白瓷中孔隙率的标准试验方法

Standard Test Method for Porosity in Vitreous Whitewares by Dye Penetration

ASTM C373-88(1999) 烧制的白色陶瓷制品的吸水率、松密度、表观孔隙率和表观比重的标准试验方法

Standard Test Method for Water Absorption, Bulk Density, Apparent Porosity, and Apparent Specific Gravity of Fired Whiteware Products

ASTM C408-88(1999) 白瓷陶瓷热导率标准测试方法

Standard Test Method for Thermal Conductivity of Whiteware Ceramics

CNS 14293-1998 实验室用参考示温锥

本标准适用于一标准系列的参考示温锥之各项特性。该系列示温锥系用以测定耐火材料在 1500 至 1800℃ 范围内示温锥耐火度之比较值。本标准规定的参考示温锥除可测定 1500 至 1800℃ 范围内的耐火度外，亦适用于 CNS 617〔耐火制品示温锥比值（耐火度）测定法〕。

Pyrometric reference cones for laboratory use

JC/T 705-1998 化工陶管及配件

Chemical ceramic pipes and accessories

ASTM C1212-98(2015) 制备包含晶粒孔隙的陶瓷参考试样的标准指南

4.1 This practice describes a method of fabricating known discontinuities in a ceramic specimen. Such specimens are needed and used in nondestructive examination to demonstrate sensitivity and resolution and to assist in establishing proper examination parameters. 1.1 This practice describes procedures for fabricating both green and sintered test bars of silicon carbide and silicon nitride containing both internal and surface voids at prescribed locations. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Fabricating Ceramic Reference Specimens Containing Seeded Voids

ASTM C1212-98(2010) 包含晶粒孔隙的陶瓷参考试样的制备

This practice describes a method of fabricating known discontinuities in a ceramic specimen. Such specimens are needed and used in nondestructive examination to demonstrate sensitivity and resolution and to assist in establishing proper examination parameters. 1.1 This practice describes procedures for fabricating both green and sintered test bars of silicon carbide and silicon nitride containing both internal and surface voids at prescribed locations. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Fabricating Ceramic Reference Specimens Containing Seeded Voids

KS L 9103-1996 瓷电极用糊料试验方法

이 규격은 자소식 전극용 페이스트의 시험 방법에 대하여 규정한다. 다만 알루미늄 전기 분

Testing method for solderberg paste

KS L 9103-1996(2021) 焊接膏的试验方法

Testing method for solderberg paste

KS L 9103-1996(2016) 测试方法SOLDERBERG PASTE

Testing method for solderberg paste