83.180 粘合剂和胶粘产品 标准查询与下载

ASTM D5868-01(2023) 纤维增强塑料（FRP）粘结的搭接剪切附着力的标准试验方法

1.1 This test method describes a lap shear test for use in measuring the bonding characteristics of adhesives for joining fiber reinforced plastics to themselves and to metals. The method is applicable to random and fiber oriented FRP. 1.2 This test method is intended to complement Test Method D1002 and extend the application to single-lap shear adhesive joints of fiber-reinforced plastic (FRP) adherends. This test method is useful for generating comparative apparent shear strength data for joints made from a number of FRP materials, providing a means by which FRP surface treatments may be compared. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Lap Shear Adhesion for Fiber Reinforced Plastic (FRP) Bonding

ASTM D3482-07a(2023) 用粘合剂测定铜的电解腐蚀的标准实施规程

1.1 This practice covers the determination of whether an adhesive has any corrosive effect on copper. It is ordinarily intended to distinguish materials that might cause corrosion in electrical and electronic equipment. This procedure is a subjective test for which precision and accuracy have not been established. It is not recommended for adhesives on backing. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Determining Electrolytic Corrosion of Copper by Adhesives

ASTM D3310-00(2023) 测定粘性材料腐蚀性的标准试验方法

1.1 This test method is intended to determine whether an adhesive material, cured or uncured, is corrosive to a metal. It is a general test method intended to screen out those materials that give a visible sign of corrosion. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Corrosivity of Adhesive Materials

ASTM D4501-01(2023) 用块剪切法测定刚性基材之间粘结强度的标准试验方法

1.1 This test method describes a procedure and fixture used to determine shear strengths of adhesives used to bond materials with moduli higher than the modulus of the adhesive. The size and shape of the specimens are variable within the physical restraints of the fixture. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Shear Strength of Adhesive Bonds Between Rigid Substrates by the Block-Shear Method

ASTM D2919-01(2023) 通过拉伸载荷测定剪切应力粘合接头耐久性的标准试验方法

1.1 This test method covers data for assessing the durability of adhesive lap-shear joints while stressed in contact with air, air in equilibrium with certain solutions, water, aqueous solutions, or other environments at various temperatures. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 7.4. 1.3 The values stated in SI units are considered to be the standard. The values in parentheses are for information only. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Durability of Adhesive Joints Stressed in Shear by Tension Loading

ASTM D3163-01(2023) 通过拉伸载荷测定剪切中粘性粘结刚性塑料搭接剪切接头强度的标准试验方法

1.1 This test method is intended to complement Test Method D1002 and extend its application to single-lap shear adhesive joints of rigid plastic adherends. The test method is useful for generating comparative shear strength data for joints made from a number of plastics. It can also provide a means by which several plastic surface treatments can be compared. 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Strength of Adhesively Bonded Rigid Plastic Lap-Shear Joints in Shear by Tension Loading

ASTM D2094-00(2023) 附着力试验用棒材和棒材试样的制备

1.1 This practice describes barand rod-type butt-joined adhesion test specimens and procedures for preparing and bonding them. The specimens are intended to be used with various adherend materials in like or unlike combinations for determining the strength properties of adhesives in accordance with Test Method D2095. 1.2 The values stated in SI units are considered to be the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Bar and Rod Specimens for Adhesion Tests

ASTM D1879-06(2023) 粘合剂样品暴露于电离辐射的标准实施规程

1.1 The purpose of this practice is to define conditions for the exposure of polymeric adhesives in bonded specimens to ionizing radiation prior to determination of radiation-induced changes in physical or chemical properties. This recommended practice specifically covers the following kinds of radiation: gamma or X-ray radiation, electron or beta radiation, neutrons, and mixtures of these such as reactor radiation. 1.2 This practice specifies only the conditions of irradiation but does not cover the preparation of test specimens, testing conditions, or the evaluation of test. These are covered in the various ASTM methods or specifications for specific materials. 1.3 This practice covers procedures for the following five types of exposure: Procedure A—Exposure at ambient conditions. Procedure B—Exposure at controlled temperature. Procedure C—Exposure in a medium other than air. Procedure D—Exposure under load. Procedure E—Exposure combining two or more of the variables listed in Procedures A to D. NOTE 1—The problems of measuring the properties of materials during irradiation involve shielding and remote control facilities and are, therefore, not considered in this practice. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5.1 Electrical Hazard: Warning—The users of this practice must be aware that there are inherent dangers associated with the use of electrical instrumentation and that this practice cannot and will not substitute for a practical knowledge of the instrument used for a particular procedure. 1.5.2 Radio Frequency: Warning—Persons with pacemakers may be affected by the radio frequency. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Exposure of Adhesive Specimens to Ionizing Radiation

ASTM D5657-07(2023) 螺纹紧固件用胶粘剂流体密封性的标准试验方法

1.1 This test method covers the determination of the ability of adhesives used for locking and sealing threaded fasteners, to make leak-tight assemblies. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Fluid Tightness Ability of Adhesives Used on Threaded Fasteners

T/ZZB 2823-2022 车灯用聚氨酯热熔胶

本文件规定了车灯用聚氨酯热熔胶（以下简称热熔胶）的基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本文件适用于以聚醚多元醇、聚酯多元醇和异氰酸酯经聚合反应制得的车灯用聚氨酯热熔胶。

Hot melt polyurethane adhesive for automotive lighting

T/ZZB 2884-2022 鞋用聚氨酯胶粘剂

本文件规定了鞋用聚氨酯胶粘剂的基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存及质量承诺。 本文件适用于鞋底和鞋面材料粘接的聚氨酯树脂型胶粘剂。 本文件不适用于鞋底和鞋面材料粘接时应用的特殊功能性表面处理剂。

Polyurethane adhesive for shoes

22/30435792 DC BS EN ISO 10364 结构粘合剂 多组分粘合剂适用期（工作寿命）的测定

BS EN ISO 10364. Structural adhesives. Determination of the pot life (working life) of multi-component adhesives

22/30456620 DC BS ISO 34257 粘合剂 木材粘合剂 高温下搭接接头拉伸强度的测定 (WATT '91)

BS ISO 34257. Adhesives. Wood adhesives. Determination of tensile strength of lap joints at elevated temperature (WATT '91)

22/30456617 DC BS ISO 34256 用于非结构木材应用的粘合剂 耐静载荷试验方法及要求

BS ISO 34256. Adhesives for non-structural wood applications. Test method and requirements for resistance to static load

T/GD1AIA 002-2022 膏药贴用热熔胶粘剂

本文件规定了膏药贴用热熔胶粘剂的基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本文件适用于膏药贴用热熔胶粘剂

Hot-melt adhesive for plaster

T/CASME 66-2022 耐高温彩色压敏胶标签

本文件规定了耐高温彩色压敏胶标签的术语和定义、技术要求、试验方法、检验规则和标志、包装、运输及贮存。

High temperature resistant color pressure sensitive adhesive label

T/CASME 49-2022 汽车用丙烯酸泡棉胶带

本文件规定了汽车用丙烯酸泡棉胶带的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。

Acrylic foam tape for automotive

T/QGCML 392-2022 不干胶标贴

本文件规定了不干胶标贴的术语和定义、产品分类、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于不干胶标贴的设计和制造。

self-adhesive label

ASTM D6195-22 线圈粘性的标准试验方法

1.1 These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface. Tack force may be measured as the force required to separate the adhesive from the adherend at the interface shortly after they have been brought into contact under a load equal only to the weight of the pressure-sensitive article (for example, tape, label, sticker, etc.) on a 1 in.2 contact area. 1.2 The following test methods are included: 1.2.1 Test Method A (using Tensile Tester), and 1.2.2 Test Method B (using Loop Tack Tester). 1.3 The values stated in inch-pound units are to be regarded as the standard because the industry standard width for pressure-sensitive tape is 1 inch. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Loop Tack

HG/T 6099-2022 标签用胶粘剂

Adhesives for labels