83.180 粘合剂和胶粘产品 标准查询与下载

T/CASMES 172-2023 动力电池用聚氨酯导热结构胶粘剂

本文件规定了动力电池用聚氨酯导热结构胶粘剂的术语和定义、基本参数、要求、试验方法、检验规则、包装、运输与贮存。 本文件适用于动力电池用聚氨酯导热结构胶粘剂（以下简称“胶粘剂”）的生产制造和检验检测。

Polyurethane thermally conductive structural adhesive for power batteries

T/CIET 172-2023 动力电池用有机硅导热灌封胶

本文件规定了动力电池用有机硅导热灌封胶(以下简称动力电池灌封胶)的术语产品分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于以聚硅氧烷为基胶,加入功能填料以及助剂配制而成的动力电池用有机硅导热灌封胶。

Power battery with silicone thermal conductivity sealing glue

T/SHPTA 046-2023 木工封边用反应型聚氨酯热熔胶

本文件给出了木工封边用反应型聚氨酯热熔胶的术语和定义、技术要求、试验方法、检验规则、包装、贮运和标志

Polyurethane Reactive Hotmelt Adhesive for Woodworking Edge Banding

T/CASME 564-2023 板材平贴用无溶剂湿固化反应型 聚氨酯热熔胶

本文件规定了板材平贴用无溶剂湿固化反应型聚氨酯热熔胶的要求、试验方法、检验规则、标志、包装、运输和贮存。

Solvent-free wet-curing reactive polyurethane hot melt adhesive for flat lamination of panels

T/CASME 560-2023 汽车内外饰零部件的水性胶喷胶技术规范

本标准规定了汽车内外饰零部件的水性胶喷胶基本要求、单组份水性喷胶、双组份水性喷胶、运行维护等内容。

Technical specification for waterborne glue spray for automotive interior and exterior trim parts

ASTM D6753/D6753M-02(2023) 煤焦油粘合剂标准规范

Standard Specification for Coal Tar Adhesive

BS EN ISO 6076:2023 粘合剂 安装地板覆盖物、木地板、找平剂和瓷砖 镘刀切口尺寸规格

1   Scope This document specifies the individual measurements of notches. It assigns specific codes used to label notched tools according to the measurements and tolerances specified in this document.

Adhesives. Installation of floor coverings, wood flooring, levelling compounds and tiles. Specification of trowel notch sizes

T/ZZB 3092-2023 电子产品用中黏度α-氰基丙烯酸乙酯瞬间胶粘剂

本文件规定了电子产品用中黏度α-氰基丙烯酸乙酯瞬间胶粘剂的基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本文件适用于电子元器件固定及粘接用的中黏度α-氰基丙烯酸乙酯瞬间胶粘剂（以下简称“瞬间胶”）。

Medium viscosity α- Ethyl cyanoacrylate instant adhesive for electronic products

BS EN 302-8:2023 用于承重木结构的粘合剂 测试方法 多粘合线试样的压缩剪切静载荷试验

1   Scope This document specifies a method of determining the ability of adhesive bonds to resist static load. It is applicable to adhesives used in load bearing timber structures. It is applicable for the following applications: a) for assessing the compliance of adhesives according to EN 301, EN 15425, EN 16254, EN 17334 and EN 17418; b) for assessing the suitability and quality of adhesives for load-bearing timber structures; c) for assessing the effect on the bond strength resulting from constant load at different climate conditions. This method is intended primarily to obtain performance data for the classification of adhesives for load bearing timber structures according to their suitability for use in defined climatic environments. This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

Adhesives for load-bearing timber structures. Test methods. Static load test of multiple bond line specimens in compression shear

T/QGCML 849-2023 水性热封胶涂层技术规范要求

本标准规定了水性热封胶涂层技术规范要求的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于水性热封胶涂层的生产及检验。

Technical specifications for water-based heat sealant coatings

T/CIET 117-2023 绿色设计产品评价技术规范 清洗剂

本文件规定了清洗剂绿色设计产品的术语和定义、评价原则和方法、评价要求和生命周期评价报告编制方法。 本文件适用于清洗剂绿色设计产品的评价。

Green Design Product Evaluation Technical Specification Cleaning Agent

ASTM D3931-08(2023) 通过压缩载荷测定间隙填充粘合剂强度的标准试验方法

1.1  This test method covers the determination of comparative shear properties of gap-filling adhesives in wood-to-wood joints at specified thicknesses of bondline in the dry condition, when tested on standard specimens under specified conditions of preparation, conditioning, and loading in compression. This test method is intended as an evaluation of gap-filling adhesives such as those used to bond plywood to lumber, lumber to lumber, and other similar materials in building constructions. 1.2  This test method also may be used to determine shear properties of gap-filling adhesives in species of wood and in thicknesses of bondline other than those specified for the comparative tests of shear properties within this test method. All procedures specified herein are applicable, excepting requirements for wood species and specific gravity, and thicknesses of bondlines. 1.3  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Strength of Gap-Filling Adhesive Bonds in Shear by Compression Loading

T/CASME 393-2023 锂电池专用抗起翘极耳胶带

本文件规定了锂电池专用抗起翘极耳胶带（以下简称胶带）的分类、要求、试验方法、检验规则、标志、包装、运输和贮存。

Anti-warping ear tape for lithium battery

ASTM D3930-08(2023) 活动房屋建筑用木基材料粘合剂的标准规范

1.1  This specification provides the means to measure and evaluate the performance of adhesives for structural or semi-structural bonding of wood-to-wood in manufactured homes. Wood as used in this specification includes lumber, plywood, particleboard, gypsum board, and all materials having wood-based surfaces at the bondline. This specification does not cover other adhesives used in manufactured homes such as adhesives for carpet, floor tile, ceramic fixtures, plastic laminates, trim and millwork, and similar nonstructural applications. 1.1.1  The performance of the adhesives is measured in the following tests: Number Test Section  1 Low Temperature 16  2 Dry Lumber 17  3 Gap-Filling 18  4 High Temperature 19  5 Type 3 Qualification 20  6 Type 2 Qualification 21  7 Aging, Film Oxidation 22  8 Aging, Bond Oxidation 23  9 Resistance to Deformation, Creep 24 10 Mold 25 11 Type 1 Qualification 26 1.2  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Adhesives for Wood-Based Materials for Construction of Manufactured Homes

ASTM D1876-08(2023) 粘合剂剥离阻力的标准测试方法（T 型剥离测试）

1.1  This test method is primarily intended for determining the relative peel resistance of adhesive bonds between flexible adherends by means of a T-type specimen. 1.2  The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. 1.3  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Peel Resistance of Adhesives (T-Peel Test)

ASTM D2095-96(2023) 用条棒试样测定粘合剂抗拉强度的标准试验方法

1.1  This test method covers the determination of the relative tensile strength of adhesives by the use of bar- and rod-shaped butt-joined specimens under defined conditions of preparation, conditioning, and testing. This test method is applicable to the testing of adhesives with various adherend materials in either similar or dissimilar combinations. Note 1:  An alternative test method for determining the tensile strength of adhesives is Test Method D897 . 1.2  The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Tensile Strength of Adhesives by Means of Bar and Rod Specimens

ASTM D2851-15(2023) 液体光学粘合剂的标准规范

1.1  This specification covers liquid optical adhesive for use in bonding glass to glass or other transparent adherends. 1.2  The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information purposes only. 1.3  The following precautionary caveat pertains only to the test method portion, Section 6 , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 6.1.1 . 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Liquid Optical Adhesive

ASTM D1582-98(2023) 液体苯酚、间苯二酚和三聚氰胺粘合剂不挥发物含量的标准测试方法

1.1  This test method covers the determination of nonvolatile content or total solids of liquid phenol, resorcinol, and melamine adhesives with or without hardener (Note 1 ) added and containing high-boiling and low-boiling volatile organic solvents or water, or both. Note 1:  Some low molecular weight materials in the adhesive may be lost if hardener is not used. When a hardener is used, it must be mixed in accordance with the manufacturer's instructions. 1.2  The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautions, see 5.2 . 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Nonvolatile Content of Liquid Phenol, Resorcinol, and Melamine Adhesives

ASTM D1062-08(2023) 金属对金属粘合剂的断裂强度的标准测试方法

1.1  This test method covers the determination of the comparative cleavage properties of adhesive bonds when tested on standard shape metal specimens under specified conditions of preparation and testing. It may be used also to compare adhesives used with other metallic materials having any specified surface treatment. 1.2  The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Cleavage Strength of Metal-to-Metal Adhesive Bonds

ASTM E866-23 蜂窝遮蔽板中粘合的铝合金用防腐粘合底漆的标准规范

1.1 This specification covers sprayable, pigmented liquid primers for use on aluminum alloys that are to be adhesively bonded in the fabrication of honeycomb sandwich panels for tactical shelters. When applied to a properly cleaned surface of aluminum alloy, the primer imparts corrosion resistance and forms a surface suitable for structural bonding using adhesives complying with Specification E865 and for coating with shelter paint finishes. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Corrosion-Inhibiting Adhesive Primer for Aluminum Alloys to Be Adhesively Bonded in Honeycomb Shelter Panels