83.180 粘合剂和胶粘产品 标准查询与下载

HG/T 6100-2022 金属压铸件用丙烯酸酯 基热固化浸渗密封胶

Acrylate-based heat-curing impregnation sealant for metal die castings

HG/T 6099-2022 标签用胶粘剂

Adhesives for labels

HG/T 6101-2022 电子元器件包装用上下 胶粘带

Upper and lower adhesive tapes for packaging electronic components

HG/T 6102-2022 通用型双向拉伸聚丙烯 膜压敏胶粘带

General purpose biaxially oriented polypropylene film pressure sensitive adhesive tape

T/GD1AIA 001-2022 粘接型导热灌封胶

本文件规定了粘接型导热灌封胶的术语和定义、分类、要求、试验方法、检验规则以及标志、包装、运输与贮存。 本文件适用于以聚硅氧烷为基胶，兼具粘结和导热能力的有机硅灌封胶。

Adhesive thermally conductive potting sealant

T/SHPTA 025-2022 纺织品用反应型聚氨酯热熔胶

本标准给出了纺织品用反应型聚氨酯热熔胶的术语和定义、技术要求、试验方法、检验规则、包装、贮运和标志

Polyurethane Reactive Hotmelt Adhesive for Textiles

T/BMCA 002-2022 各向同性导电胶粘剂试验技术规程

1、术语和定义：对各向同性导电胶粘剂、体积电阻率、导热系数给出了相应的定义。 2、规定了试验的通用要求，包括试验环境条件、状态调节、试验条件的容许误差、试验设施和仪器、受试产品的相关要求； 3、明确了试验项目和内容，将试验项目分为型式检验、出厂检验和入厂复验，并在表中列出了16个需要检验的项目； 4、规定“每一种导电胶粘剂应分别进行固化前导电胶粘剂性能试验与固化后导电胶粘剂性能试验。”并且详细规定了外观检查、粘度、触变指数等各个试验项目的试验程序； 5、规定试验报告应包括以下内容： a) 标准编号；b) 导电胶粘剂的名称及其它数据，包括主体材料的种类、填料、制造商代码、生产批号等； c) 试样的类型和制备方法； d) 试样的数量； e) 试验日期； f) 试验内容以及试验条件； g) 试验数据； h) 试验结果。

Technical specification for test of isotropic electrically conductive adhesive

ASTM D2235-22 丙烯腈-丁二烯-苯乙烯（ABS）塑料管和配件用溶剂水泥的标准规范

1.1 This specification covers solvent cement for joining acrylonitrile-butadiene styrene (ABS) plastic pipe and fittings for pressure and nonpressure systems. 1.2 Recommendation for using solvent cement for joining acrylonitrile-butadiene-styrene (ABS) plastic pipe and fittings is given in Appendix X1. Satisfactory joining of pipe and fittings cannot be made in the presence of water, as water destroys the bonding ability of solvent cement; therefore, all materials must be dry for satisfactory joining. 1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

ASTM D3359-22 用胶带试验评定附着力的标准试验方法

1.1 These test methods cover procedures for assessing the adhesion of relatively ductile coating films to metallic substrates by applying and removing pressure-sensitive tape over cuts made in the film. 1.2 Test Method A is primarily intended for use in the field while Test Method B is more suitable for use in laboratory or shop environments. Also, Test Method B is not considered suitable for films thicker than 125 µm (5 mils) unless wider spaced cuts are employed and there is an explicit agreement between the purchaser and seller. 1.3 These test methods are used to evaluate whether the adhesion of a coating to a substrate is adequate for the user’s application. They do not distinguish between higher levels of adhesion for which more sophisticated methods of measurement are required. 1.4 This test method is similar in content (but not technically equivalent) to ISO 2409. 1.5 In multicoat systems adhesion failure may occur between coats so that the adhesion of the coating system to the substrate is not determined. 1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Rating Adhesion by Tape Test

T/ZSPRINT 001-2022 覆膜铁用双组份聚氨酯干式复合胶粘剂

该标准规定了覆膜铁用双组份聚氨酯干式复合胶粘剂的技术要求、实验方法、检验规则、包装运输和贮存等，为该产业的生产、检测和监管等提供标准化技术支撑，填补了相关标准空白。具有前瞻性、可持续性、规范性和先进性，对规范和引导国内覆膜铁用双组份聚氨酯干式复合胶粘剂的各项要求具有积极的引领作用。

Specially used for the laminated Steel two-component polyurethane adhesive

BS ISO 21368:2022 粘合剂 胶粘结构的制造指南和适合此类结构风险评估的报告程序

1   Scope This document provides guidelines describing the adhesive bonding quality requirements suitable for use by adhesive user-companies utilizing adhesive bonding as a means of fabrication. In particular, the guidelines define various approaches to meeting quality requirements for fabrication and reporting procedures, both in workshops and on site. These guidelines aim to convey the importance of maintaining quality standards in fabrication and reporting procedures, keeping records and thus enabling documentation to provide the basis for risk evaluation of adhesively bonded structures in service and in use. These guidelines have been prepared such that: a) they are independent of the type of adhesively bonded structure ; b) they are independent of adhesive user-companies ’ and suppliers’ product recommendations; c) they define the quality requirements for adhesive bonding in terms of fabrication and reporting procedures, both in workshops and on site; d) they can be used as the basis for risk evaluation of adhesively bonded structures in service and in use;

Adhesives. Guidelines for the fabrication of adhesively bonded structures and reporting procedures suitable for the risk evaluation of such structures

T/SZBX 059-2022 超薄压敏胶粘带

本文件规定了超薄压敏胶粘带（以下简称超薄胶带）的产品分类、要求、试验方法、检验规则、标志、包装、运输和贮存

Double sided pressure sensitive adhesive tapes

KS M ISO 7387-1-2022 PVC U管件组装用溶剂粘合剂 特性 第1部分：基本试验方法

Adhesives with solvents for assembly of PVC－U pipe elements－Characterization－Part 1：Basic test methods

ASTM E1794-22a 粘合泡沫芯夹层板（200°F高湿度环境）II型板用粘合剂的标准规范

1.1 This specification covers two-part adhesives for bonding foam core sandwich panels. The adhesive may be used for new production or depot maintenance. The adhesive should be suitable for forming bonds that can withstand long-term exposure to temperatures from −55 °C to 93 °C (−67 °F to 200 °F) and also withstand combinations of stress, temperature, and humidity expected to be encountered in service. The adhesives shall be used for bonding aluminum alloy facing to foam core, inserts, internal aluminum framing members, and other components of a foam cored sandwich panel. 1.2 The values stated in SI units are to be regarded as the standard where only SI units are given or where SI units are given first followed by inch-pound units; where inch-pound units are given first followed by SI units, the inch-pound units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Adhesive for Bonding Foam Cored Sandwich Panels (200 °F Elevated Humidity Service), Type II Panels

ASTM D5570/D5570M-10(2022) 箱盖用胶带和粘合剂耐水性的标准试验方法

1.1 This test method covers a procedure to determine the water resistance of an adhesive or tape as measured by the amount of tape or adhesive dissolved or dispersed in water. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Water Resistance of Tape and Adhesives Used as Box Closure

BS EN ISO 11339:2022 粘合剂 柔性对柔性粘合组件的 T 型剥离测试

What is ISO 11339 - T-peel test for flexible to flexible bonded assemblies about?    ISO 11339 is an international organisation for standardization that specifies a Tpeel test for the determination of the peel resistance of an adhesive by measuring the peeling force of a Tshaped bonded assembly of two flexible adherends.   This test procedure does not provide design information.   Note 1: The method in ISO 11339 was originally developed for use with metal adherends but other, flexible, adherends can also be used.  Note 2: Persons using ISO 11339 should be familiar with normal laboratory practice, if applicable. ISO 11339 does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility...

Adhesives. T-peel test for flexible-to-flexible bonded assemblies

BS EN ISO 10365:2022 粘合剂 主要失效模式的指定

What is ISO 10365 - Designation of main failure patterns in adhesives about?    ISO 10365 is an international organisation for standardization that specifies the designations for the main types of failure patterns of bonded assemblies and illustrates, through diagrams, their respective appearances.   ISO 10365 applies to all mechanical tests performed on a bonded assembly, regardless of the nature of the adherents and adhesive which make up the assembly.   Who is ISO 10365 - Designation of main f...

Adhesives. Designation of main failure patterns

ASTM E1794-22 粘合泡沫芯夹层板（200°F高湿度环境）II型板用粘合剂的标准规范

Standard Specification for Adhesive for Bonding Foam Cored Sandwich Panels (200 °F Elevated Humidity Service), Type II Panels

ISO 21368:2022 粘合剂.粘合结构的制造指南和适用于此类结构风险评估的报告程序

This document provides guidelines describing the adhesive bonding quality requirements suitable for use by adhesive user-companies utilizing adhesive bonding as a means of fabrication. In particular, the guidelines define various approaches to meeting quality requirements for fabrication and reporting procedures, both in workshops and on site. These guidelines aim to convey the importance of maintaining quality standards in fabrication and reporting procedures, keeping records and thus enabling documentation to provide the basis for risk evaluation of adhesively bonded structures in service and in use. These guidelines have been prepared such that: a) they are independent of the type of adhesively bonded structure; b) they are independent of adhesive user-companies’ and suppliers’ product recommendations; c) they define the quality requirements for adhesive bonding in terms of fabrication and reporting procedures, both in workshops and on site; d) they can be used as the basis for risk evaluation of adhesively bonded structures in service and in use; e) they can be used as a basis for assessing a fabricator's capability to produce adhesively bonded structures fulfilling specified quality requirements when they are detailed in one or more of the following: — a contract between the parties involved; — an application standard; — a regulatory statement. The guidelines contained within this document can be adopted in full or selectively chosen by the adhesive user to suit the structure concerned. The guidelines provide a flexible framework for the control of adhesive bonding activities in the following cases. Case 1 The provision of specific requirements for adhesive bonding in contracts that require the adhesive user to have a quality system other than ISO 9001. Case 2 The provision of specific requirements for adhesive bonding as guidance to an adhesive user developing a quality system. Case 3 The provision of specific requirements for references in application standards that uses adhesive bonding as part of its requirements or in a contract between relevant parties. 1 Case 4 The provision of a framework for fabrication and reporting procedures to a quality standard, suitable in particular as a basis for the risk evaluation of adhesively bonded structures.

Adhesives — Guidelines for the fabrication of adhesively bonded structures and reporting procedures suitable for the risk evaluation of such structures

BS ISO 17194:2022 结构粘合剂 标准属性数据库

What is ISO 17194 - Properties of structural adhesives about? ISO 17194 is one of a series of standards on structural adhesives. ISO 17194 specifies a set of basic properties commonly required for the selection and use of structural adhesives in different applications. ISO standard test methods and test conditions are also reviewed for the measurement of these data to facilitate traceability of recorded values Who is ISO 17194 - Properties of structural adhesives for ? ISO 17194 on structural adhesives is useful for: Manufacturers of structural adhesives Suppliers and dealers of structural adhesives Civil engineers Architects Repair and maintenance personnel Testing and inspection personnel Why should you use ISO 17194 -

Structural adhesives. Standard database of properties