83.200 橡胶和塑料工业设备 标准查询与下载

NF E63-606:2008 塑料和橡胶加工机械.压力机.安全要求

Plastics and rubber machines - Presses - Safety requirements.

EN 12012-4:2006+A1:2008 塑料和橡胶机械.粉碎机.第4部分:凝聚剂的安全要求

This European Standard specifies the essential safety requirements applicable to the design and construction of agglomerators used to densify plastic scrap, reducing its size and/or volume. The limits of the agglomerator are as follows: the outer edge of the feed opening, or outer edge of the fixed feed device (e. g. hopper) or the interface between the feed system (e. g. conveyor) and the agglomerator chamber and the outer edge of the discharge opening of the agglomerator chamber or the interface between the agglomerator chamber and the discharge system. Only the significant hazards listed in Clause 4 and dealt with in Clause 5 are subject to this European Standard. This European Standard does not deal with hazards caused by processing materials (such as Expanded Polystyrene (EPS) and Polyurethane (PU) foam) which, when heated, may lead to a risk of fire and release of toxic gases. This European Standard does not deal with hazards caused by upstream and/or downstream equipment. This European Standard is not applicable to agglomerators manufactured before the date of its approval as EN.

Plastics and rubber machines - Size reduction machines - Part 4: Safety requirements for agglomerators

DS/EN 289+A1:2008 塑料和橡胶机械 压力机 安全要求

This document specifies the essential safety requirements for hydraulic presses, including toggle and hydromechanic ones, with a vertical closing movement more than 6 mm for the moulding of plastics and/or rubber. This document covers both compression moulding (see 3.1.1) and transfer moulding (see 3.1.2). All hazards listed in clause 4 are covered by this document. The following machines are excluded: - injection moulding machines (see EN 201); - presses for curing pneumatic tyres; - presses for curing inner tubes and curing bags; - hydraulic presses as covered by EN 693; - mechanical presses as covered by EN 692; - thermoforming machines (see EN 12409); -

Plastics and rubber machines - Presses - Safety requirements

JB/T 10899-2008 塑料挤出双壁波纹管辅机

本标准规定了塑料挤出双壁波纹管辅机（以下简称双壁管辅机）的术语、基本参数、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于与挤出机配套使用，能将挤出的熔体制成双壁波纹管的成型机械。本标准主要适用于塑料：聚烯烃（PE、PP）、硬聚氯乙烯（PVC-U）等。

Plastics double wall corrugated pipes extruder accessory

JB/T 10898-2008 塑料挤出复合膜辅机

本标准规定了塑料挤出复合膜辅机的基本参数、要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于塑料挤出复合膜辅机（以下简称复膜机）。

Plastics extrusion laminate film accessory

JB/T 5438-2008 塑料机械.术语

本标准规定了有关塑料机械的术语和定义。 本标准适用于塑料机械行业在教学、科研、设计、制造、制修订标准、编写相关技术文件和书刊、及技术交流时使用。

Plastics machinery. Terminology

JB/T 5419-2008 塑料挤出平膜扁丝辅机

本标准规定了塑料挤出平膜扁丝辅机的基本参数、要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于塑料挤出平膜扁丝辅机（以下简称辅机）。

Plastics filature fiber extrusion accessory

JB/T 5290-2008 塑料圆织机

本标准规定了塑料圆织机的基本参数、要求、试验方法、检验规则和标志、包装、运输和贮存。 本标准适用于塑料圆织机（以下简称圆织机）。

Plastics circular loom, plastics circular braider

JB/T 2627-2008 塑料挤出硬管辅机

本标准规定了塑料挤出硬管辅机的术语、基本参数、技术要求、试验方法和检验规则、标志、使用说明书、包装、运输和贮存。 本标准适用于与挤出机配套使用，能将挤出的熔体制成硬质塑料管的成型机械。

Plastics pipe extrusion accessory

DIN EN 14886:2008 塑料和橡胶机械.块状泡沫塑料用带刀切削机.安全要求

This European standard applies to machines that are designed specifically to cut, split or peel block foams to commercially required shapes, using a single or double cut. All hazards listed in clause 4 are covered by this document. Cutting of block foams may be by: -- vertical cutting; -- horizontal cutting; -- inclined cutting; -- transverse cutting; -- contour cutting; or -- a combination of the above. The material to be cut may be supported or transported by: -- a fixed table; -- a shuttle table; -- a conveyor; -- a turntable; -- rollers; -- mandrel; or -- a combination of the above. Cutting can be either manual or automatic. Cutting tools can be: -- smooth-edged or toothed bandknives; -- cutting wires. Movement of the cutting tool can be either oscillating or continuous in one direction. This European Standard does not apply to: -- laser and water jet cutting; -- hot wire cutting; -- wood, metal and food cutting machines. The safety requirements for the additional hazards arising from the interaction between bandknife cutting machines and ancillary equipment, especially loading and unloading devices, are specified. The safety requirements for the ancillary equipment itself are not specified. This European Standard covers machines used for cutting plastics and rubber having a cellular or compact structure. However, it may also be applied when these machines are used for cutting other materials, for example textiles, fibres and mineral wool, if cutting these materials does not create additional hazards. This document is not applicable to bandknife cutting machines manufactured before the date of its publication as an EN.

Plastics and rubber machines - Bandknife cutting machines for block foams - Safety requirements; English version of DIN EN 14886:2008-06

LST EN 14886-2008 塑料和橡胶机械 块状泡沫的带刀切割机 安全要求

Plastics and rubber machines - Bandknife cutting machines for block foams - Safety requirements

DS/EN 14886:2008 塑料和橡胶机械 块状泡沫的带刀切割机 安全要求

This European standard applies to machines that are designed specifically to cut, split or peel block foams to commercially required shapes, using a single or double cut. All hazards listed in clause 4 are covered by this document.Cutting of block foams may be by: - vertical cutting; - horizontal cutting; - inclined cutting;- transverse cutting; - contour cutting; or- a combination of the above.The material to be cut may be supported or transported by:- a fixed table;- a shuttle table;- a conveyor;- a turntable;- rollers;- mandrel; or- a combination of the above. Cutting can be either manual or automatic.Cutting tools can be:- smooth-edged or toothed bandkn

Plastics and rubber machines - Bandknife cutting machines for block foams - Safety requirements

BS EN 14886:2008 橡胶和塑料机械.块状塑料泡沫用带刀切削机.安全要求

This European standard applies to machines that are designed specifically to cut, split or peel block foams to commercially required shapes, using a single or double cut. All hazards listed in clause 4 are covered by this document. Cutting of block foams may be by:  vertical cutting;  horizontal cutting;  inclined cutting;  transverse cutting;  contour cutting; or  a combination of the above. The material to be cut may be supported or transported by:  a fixed table;  a shuttle table;  a conveyor;  a turntable;  rollers;  mandrel; or  a combination of the above. Cutting can be either manual or automatic. Cutting tools can be:  smooth-edged or toothed bandknives;  cutting wires. Movement of the cutting tool can be either oscillating or continuous in one direction. This European Standard does not apply to:  laser and water jet cutting;  hot wire cutting;  wood, metal and food cutting machines. The safety requirements for the additional hazards arising from the interaction between bandknife cutting machines and ancillary equipment, especially loading and unloading devices, are specified. The safety requirements for the ancillary equipment itself are not specified. This European Standard covers machines used for cutting plastics and rubber having a cellular or compact structure. However, it may also be applied when these machines are used for cutting other materials, for example textiles, fibres and mineral wool, if cutting these materials does not create additional hazards. This document is not applicable to bandknife cutting machines manufactured before the date of its publication as an EN.

Plastics and rubber machines - Bandknife cutting machines for block foams - Safety requirements

LST EN 15067-2008 塑料和橡胶机械 袋子和袋子的薄膜加工机 安全要求

Plastics and rubber machines - Film converting machines for bags and sacks - Safety requirements

DS/EN 15067:2008 塑料和橡胶机械 袋子和袋子的薄膜加工机 安全要求

This European Standard specifies the safety requirements applicable to the design and construction of film converting machines for making bags and sacks, for the significant and specific hazards listed in Clause 4.This type of machine is based on the welding process.A film converting machine for bags and sacks starts at the film unwinding unit or at the film inlet when this machine is directly fed by an upstream process and ends at the product collection or delivery unit. The bag making line may include:1) unwind units2) slit-welding units3) gussetting units 4) lane deviation units 5) perforating and welding or cutting and welding units6) blocking units7) p

Plastics and rubber machines - Film converting machines for bags and sacks - Safety requirements

DIN EN 15067:2008 塑料和橡胶设备.袋子用薄膜加工机.安全要求

This European Standard specifies the safety requirements applicable to the design and construction of film converting machines for making bags and sacks, for the significant and specific hazards listed in Clause 4. This type of machine is based on the welding process. A film converting machine for bags and sacks starts at the film unwinding unit or at the film inlet when this machine is directly fed by an upstream process and ends at the product collection or delivery unit. The bag making line may include: 1 ) unwind units 2) slit-welding units 3) gussetting units 4) lane deviation units 5) perforating and welding or cutting and welding units 6) blocking units 7) pick-up and transfer units 8) stacking units 9) punching units 10) folding units 11 ) winding units 12) labelling or taping units 13) handle and closure units 14) draw tape insertion units 15) generators of electrostatic charge 16) electrostatic discharge equipment. Printing units, high frequency welding machines and the design and construction of electrostatic generators are not covered by this standard. Ultrasonic radiation hazards resulting from ultrasonic welding devices, e.g. integrated in handle and closure units, are not covered by this standard. Film converting machines for bags and sacks generally do not create explosive atmospheres. In principle they therefore correspond with line F of Table 2 of the ATEX Guideline and consequently do not fall within the scope of Directive 94/9/EC. This document is not applicable to machines which are manufactured before the date of its publication as EN.

Plastics and rubber machines - Film converting machines for bags and sacks - Safety requirements; English version of DIN EN 15067:2008-03

EN 14886:2008 塑料和橡胶机械.块状泡沫塑料用带刀切削机.安全要求

This document applies to machines that are designed specifically to cut, split or peel block foams to commercially required shapes, using a single or double cut. All hazards listed in clause 4 are covered byThis document. Cutting of block foams may be by:vertical cutting; horizontal cutting; inclined cutting; transverse cutting; contour cutting; or a combination of the above.The material to be cut may be supported or transported by:a fixed table; a shuttle table; a conveyor; a turntable; rollers; mandrel; or a combination of the above. Cutting can be either manual or automatic. Cutting tools can be:smooth-edged or toothed bandknives; cutting wires. Movement of the cutting tool can be either oscillating or continuous in one direction.This European Standard does not apply to:laser and water jet cutting; hot wire cutting; wood, metal and food cutting machines.The safety requirements forThe additional hazards arising fromThe interaction between bandknife cutting machines and ancillary equipment, especially loading and unloading devices, are specified.The safety requirements forThe ancillary equipment itself are not specified.This European Standard covers machines used for cutting plastics and rubber having a cellular or compact structure. However, it may also be applied whenThese machines are used for cutting other materials, for example textiles, fibres and mineral wool, if cuttingThese materials does not create additional hazards.This document is not applicable to bandknife cutting machines manufactured beforeThe date of its publication as an EN.

Plastics and rubber machines - Bandknife cutting machines for block foams - Safety requirements

CEN EN 14886-2008_ 塑料和橡胶机械.块状泡沫塑料带型刀切削加工设备.安全要求

This European standard applies to machines that are designed specifically to cut, split or peel block foams to commercially required shapes, using a single or double cut. All hazards listed in clause 4 are covered by this document. Cutting of block foams may be by: ? vertical cutting; ? horizontal cutting; ? inclined cutting; ? transverse cutting; ? contour cutting; or ? a combination of the above. The material to be cut may be supported or transported by: ? a fixed table; ? a shuttle table; ? a conveyor; ? a turntable; ? rollers; ? mandrel; or ? a combination of the above. Cutting can be either manual or automatic. Cutting tools can be: ? smooth-edged or toothed bandknives; ? cutting wires. Movement of the cutting tool can be either oscillating or continuous in one direction. This European Standard does not apply to: ? laser and water jet cutting; ? hot wire cutting; ? wood, metal and food cutting machines. The safety requirements for the additional hazards arising from the interaction between bandknife cutting machines and ancillary equipment, especially loading and unloading devices, are specified. The safety requirements for the ancillary equipment itself are not specified. This European Standard covers machines used for cutting plastics and rubber having a cellular or compact structure. However, it may also be applied when these machines are used for cutting other materials, for example textiles, fibres and mineral wool, if cutting these materials does not create additional hazards. This document is not applicable to bandknife cutting machines manufactured before the date of its publication as an EN.

Plastics and rubber machines — Bandknife cutting machines for block foams — Safety requirements

BS EN 15067:2007 塑料和橡胶机械.袋子用薄膜吹炉冶炼机.安全要求

This European Standard specifies the safety requirements applicable to the design and construction of film converting machines for making bags and sacks, for the significant and specific hazards listed in Clause 4. This type of machine is based on the welding process. A film converting machine for bags and sacks starts at the film unwinding unit or at the film inlet when this machine is directly fed by an upstream process and ends at the product collection or delivery unit. The bag making line may include: 1) unwind units 2) slit-welding units 3) gussetting units 4) lane deviation units 5) perforating and welding or cutting and welding units 6) blocking units 7) pick-up and transfer units 8) stacking units 9) punching units 10) folding units 11) winding units 12) labelling or taping units 13) handle and closure units 14) draw tape insertion units 15) generators of electrostatic charge 16) electrostatic discharge equipment. Printing units, high frequency welding machines and the design and construction of electrostatic generators are not covered by this standard. Ultrasonic radiation hazards resulting from ultrasonic welding devices, e.g. integrated in handle and closure units, are not covered by this standard. Film converting machines for bags and sacks generally do not create explosive atmospheres. In principle they therefore correspond with line F of Table 2 of the ATEX Guideline and consequently do not fall within the scope of Directive 94/9/EC. This document is not applicable to machines which are manufactured before the date of its

Plastics and rubber machines - Film converting machines for bags and sacks - Safety requirements

EN 12409:2008 塑料和橡胶机械.加热成形机.安全要求

This European Standard deals with all significant hazards, hazardous situations and events relevant to thermoforming machines for continuous sheet and single sheets of thermoplastics materials, when they are used as intended and under conditions of misuse which are foreseeable by the manufacturer (see Clause 4). A thermoforming machine may consist of a forming unit or a forming unit linked to one or more additional units.This standard covers the following units: continuous sheet unwind unit; single sheet feed unit; material intake; conveying equipment; heating unit; preheating unit; edge heating unit; component feeding/inserting unit; forming station; finishing station; stacking station; discharge station; residual sheet winding unit; sheet cutting unit.This European Standard does not apply to units mounted upstream or downstream of the thermoforming machine: which have a separate control system; and/or are located separately. NOTE 1This European Standard specifies requirements for machines supplied as a single forming unit or a number of units designed to operate as a single machine. Additional units that may be introduced at a later stage should be considered separately applying relevant standards and taking into account any hazards arising through their interaction with the thermoforming machine.This European Standard does not apply to units which are integrated into form, fill and seal machines. These are covered in EN 415-3:1999.This European Standard does not apply to units which incorporate heating systems which are fuelled by gas. NOTE 2 Thermoforming machines generally do not create explosive atmospheres. In principle they therefore correspond with line F of Table 2 of the ATEX Guideline and consequently do not fall within the scope of Directive 94/9/EC.This European Standard is not applicable to thermoforming machines which are manufactured before the date of its publication as EN.

Plastics and rubber machines - Thermoforming machines - Safety requirements (Incorporates Amendment A1: 2011)