83.200 橡胶和塑料工业设备 标准查询与下载

LST EN 12409-2008+A1-2012 塑料和橡胶机械 热成型机 安全要求

Plastics and rubber machines - Thermoforming machines - Safety requirements

DIN EN 1114-1:2012 塑料和橡胶机械.挤压机和挤塑生产流水线.第1部分:挤压机安全要求.德文版 EN 1114-1-2011

Plastics and rubber machines - Extruders and extrusion lines - Part 1: Safety requirements for extruders; German version EN 1114-1:2011

ASTM D957-12 塑料用模具表面温度测定的标准实施规程

1.1 This practice is intended for determining the temperature at a specified point or points on the surface of the cavity and base of a mold for plastics. By determining the temperature at as many points as deemed necessary, the overall temperature condition of the surface can be determined. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 1???There is no known ISO equivalent to this standard.

Standard Practice for Determining Surface Temperature of Molds for Plastics

DS/EN 12409+A1:2011 塑料和橡胶机械 热成型机 安全要求

This European Standard deals with all significant hazards, hazardous situations and events relevant to thermoforming machines for continuous sheet and single sheets of thermoplastics materials, when they are used as intended and under conditions of misuse which are foreseeable by the manufacturer (see Clause 4).A thermoforming machine may consist of a forming unit or a forming unit linked to one or more additional units. This standard covers the following units:- continuous sheet unwind unit;- single sheet feed unit;- material intake;- conveying equipment;- heating unit;- preheating unit;- edge heating unit;- component feeding/inserting unit;- forming stati

Plastics and rubber machines - Thermoforming machines - Safety requirements

NF E63-607-1*NF EN 1114-1:2011 橡胶和塑料机械.挤压机和挤压生产线.第1部分:挤压机的安全要求

Plastics and rubber machines - Extruders and extrusion lines - Part 1 : safety requirements for extruders.

DIN EN 12409:2011 塑料和橡胶机械.热成型机械.安全要求.德文版 EN 12409-2008+A1-2011

This European Standard deals with all significant hazards, hazardous situations and events relevant to thermoforming machines for continuous sheet and single sheets of thermoplastics materials,when they are used as intended and under conditions of misuse which are foresseable by the manufacturer(see Clause 4).

Plastics and rubber machines - Thermoforming machines - Safety requirements; German version EN 12409:2008+A1:2011

BS EN 1114-1:2011 橡胶和塑料制造机器.挤压机和挤压工作线.第1部分:挤压设备的安全性要求

Plastics and rubber machines. Extruders and extrusion lines. Safety requirements for extruders

GSO EN 12409:2011 橡胶和塑料机械 热成型机 安全要求

This European Standard deals with all significant hazards, hazardous situations and events relevant to thermoforming machines for continuous sheet and single sheets of thermoplastics materials, when they are used as intended and under conditions of misuse which are foreseeable by the manufacturer (see Clause 4). A thermoforming machine may consist of a forming unit or a forming unit linked to one or more additional units. This standard covers the following units: - continuous sheet unwind unit; - single sheet feed unit; - material intake; - conveying equipment; - heating unit; - preheating unit; - edge heating unit; - component feeding/inserting unit; - forming station; - finishing station; - stacking station; - discharge station; - residual sheet winding unit; - sheet cutting unit. This European standard does not apply to units mounted upstream or downstream of the thermoforming machine: - which have a separate control system; and/or - are located separately. NOTE 1 This European Standard specifies requirements for machines supplied as a single forming unit or a number of units designed to operate as a single machine. Additional units that may be introduced at a later stage should be considered separately applying relevant standards and taking into account any hazards arising through their interaction with the thermoforming machine. This European Standard does not apply to units which are integrated into form, fill and seal machines. These are covered in EN 415-3:1999. This European standard does not apply to units which incorporate heating systems which are fuelled by gas. NOTE 2 Thermoforming machines generally do not create explosive atmospheres. In principle they therefore correspond with line F of Table 2 of the ATEX Guideline and consequently do not fall within the scope of Directive 94/9/EC. This European Standard is not applicable to thermoforming machines which are manufactured before the date of its publication as EN.

Rubber and plastics machines - Thermoforming machines - Safety requirements

GSO EN 13418:2011 橡胶和塑料机械 箔或片材卷绕机 安全要求

This European Standard specifies the safety requirements for the design and construction of winding, unwinding and rewinding machines for film or sheet manufactured from rubber, plastics and composite materials in respect of the significant hazards listed in clause 4. A winding machine begins at the intake of the film or sheet into the winding machine and ends at the discharge position of the reel(s). An unwinding machine begins at the take-up position of the reel(s) and ends at the film or sheet take-off point. A rewinding machine begins at the take-up position of the reel(s) and ends at the discharge position of the reel(s). In some machines the winding, unwinding and rewinding functions may be combined. The following functional groups are covered by this European Standard: - fixed point roll; - film or sheet tension control; - winding zone; - reel change device; - reel loading and unloading devices; and the following additional equipment integrated into the winding machine: - spreader roll device; - longitudinal cutting unit; - slitting device; - film or sheet alignment device; - static eliminator. Technical safety requirements for the design and construction of aids for lifting and handling, e.g. of winding cores or reels, are not covered by this standard. Technical safety requirements for the design and construction of thickness monitoring devices are not covered by this standard. Hazards due to electro-magnetic radiation, e.g. from the use of thickness monitoring devices, are not covered by this standard. Toxic or chemical hazards and hazards due to dusts, fumes or gases, which could occur from the materials being wound are not covered by this standard. NOTE Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard is not intended to provide means of complying with the essen

Rubber and plastics machines - Winding machines for film or sheet - Safety requirements

GSO EN 15067:2011 塑料和橡胶机器 用于制造袋子和袋子的塑料箔转换机器 安全要求

This European Standard specifies the safety requirements applicable to the design and construction of film converting machines for making bags and sacks, for the significant and specific hazards listed in Clause 4. This type of machine is based on the welding process. A film converting machine for bags and sacks starts at the film unwinding unit or at the film inlet when this machine is directly fed by an upstream process and ends at the product collection or delivery unit. The bag making line may include: 1) unwind units 2) slit-welding units 3) gussetting units 4) lane deviation units 5) perforating and welding or cutting and welding units 6) blocking units 7) pick-up and transfer units 8) stacking units 9) punching units 10) folding units 11) winding units 12) labelling or taping units 13) handle and closure units 14) draw tape insertion units 15) generators of electrostatic charge 16) electrostatic discharge equipment. Printing units, high frequency welding machines and the design and construction of electrostatic generators are not covered by this standard. Ultrasonic radiation hazards resulting from ultrasonic welding devices, e.g. integrated in handle and closure units, are not covered by this standard. Film converting machines for bags and sacks generally do not create explosive atmospheres. In principle they therefore correspond with line F of Table 2 of the ATEX Guideline and consequently do not fall within the scope of Directive 94/9/EC. This document is not applicable to machines which are manufactured before the date of its publication as EN.

Plastics and rubber machines - Film converting machines for bags and sacks - Safety requirements

EN 12409:2008+A1:2011 塑料和橡胶机械.加热成形机.安全要求 包含修改件A1,2011

This European Standard deals with all significant hazards, hazardous situations and events relevant to thermoforming machines for continuous sheet and single sheets of thermoplastics materials, when they are used as intended and under conditions of misuse which are foreseeable by the manufacturer (see Clause 4). A thermoforming machine may consist of a forming unit or a forming unit linked to one or more additional units. This standard covers the following units: - continuous sheet unwind unit; - single sheet feed unit; - material intake; - conveying equipment; - heating unit; - preheating unit; - edge heating unit; - component feeding/inserting unit; - forming station; - finishing station; - stacking station; - discharge station; - residual sheet winding unit; - sheet cutting unit. This European standard does not apply to units mounted upstream or downstream of the thermoforming machine: - which have a separate control system; and/or - are located separately. NOTE 1 This European Standard specifies requirements for machines supplied as a single forming unit or a number of units designed to operate as a single machine. Additional units that may be introduced at a later stage should be considered separately applying relevant standards and taking into account any hazards arising through their interaction with the thermoforming machine. This European Standard does not apply to units which are integrated into form, fill and seal machines. These are covered in EN 415-3:1999. This European standard does not apply to units which incorporate heating systems which are fuelled by gas. NOTE 2 Thermoforming machines generally do not create explosive atmospheres. In principle they therefore correspond with line F of Table 2 of the ATEX Guideline and consequently do not fall within the scope of Directive 94/9/EC. This European Standard is not applicable to thermoforming machines which are manufactured before the date of its publication as EN.

Plastics and rubber machines - Thermoforming machines - Safety requirements

GSO EN 12012-1:2011 塑料和橡胶机械 粉碎机 第1部分：刀片造粒机的安全要求

This document specifies the essential safety requirements applicable to the design and construction of blade granulators used to reduce objects and materials made from plastics and rubber into granules. The machine begins with the outer edge of the feed opening, or feeding device if it is an integral part of the machine, and ends with the discharge area. Only the significant hazards listed in clause 4 and dealt with in clause 5 are subject to this document. This document does not deal with hazards caused by processing harmful materials. This document is not applicable to machines which are manufactured before the date of its publication as an EN.

Plastics and rubber machines - Size reduction machines - Part 1: Safety requirements for blade granulators

GSO EN 1114-1:2011 橡胶和塑料机械 挤出机和挤出生产线 第1部分：挤出机的安全要求

This European Standard specifies all significant hazards, hazardous situations and events relevant to all types of screw extruders for plastics and rubber, when they are used as intended and under conditions of misuse which are foreseeable by the manufacturer (see Clause 4). This European Standard additionally covers the following feeding systems: - hoppers; - single roller feed; - double roller feed; - crammer feeder; and the following ancillary equipment which form part of or are attached to the extruder: - screen changers; - melt/gear pumps; - melt pipes and adaptors; - static mixers; - extruder head that give initial shape to the extruded material. NOTE Metering devices are not covered by this standard. This European Standard does not deal with hazards caused by the processing of materials and which may lead to a risk of fire or release of health hazardous materials. An extruder conforming to this document is not regarded as a pressure vessel as defined in the Pressure Equipment Directive 97/23/EC. Extruders usually do not produce explosive atmospheres. Where materials are processed, which may cause an explosive atmosphere, the Directive 94/9/EC on the Equipment intended for use in Potentially Explosive Atmospheres (ATEX) should be applied. Explosion hazards are not dealt with in this document. This European Standard is not applicable to extruders which are manufactured before the date of its publication as EN.

Rubber and plastics machines - Extruders and extrusion lines - Part 1: Safety requirements for extruders

GSO EN 12012-4:2011 塑料和橡胶机械 粉碎机 第4部分：造粒机的安全要求

This European Standard specifies the essential safety requirements applicable to the design and construction of agglomerators used to densify plastic scrap, reducing its size and/or volume. The limits of the agglomerator are as follows: - the outer edge of the feed opening, or outer edge of the fixed feed device (e.g. hopper) or the interface between the feed system (e.g. conveyor) and the agglomerator chamber and - the outer edge of the discharge opening of the agglomerator chamber or the interface between the agglomerator chamber and the discharge system. Only the significant hazards listed in Clause 4 and dealt with in Clause 5 are subject to this European Standard. This European Standard does not deal with hazards caused by processing materials (such as Expanded Polystyrene (EPS) and Polyurethane (PU) foam) which, when heated, may lead to a risk of fire and release of toxic gases. This European Standard does not deal with hazards caused by upstream and/or downstream equipment. This European Standard is not applicable to agglomerators manufactured before the date of its approval as EN

Plastics and rubber machines - Size reduction machines - Part 4: Safety requirements for agglomerators

GSO EN 14886:2011 塑料和橡胶机 用于泡沫块的带刀切割机 安全要求

This European standard applies to machines that are designed specifically to cut, split or peel block foams to commercially required shapes, using a single or double cut. All hazards listed in clause 4 are covered by this document. Cutting of block foams may be by: ? vertical cutting; ? horizontal cutting; ? inclined cutting; ? transverse cutting; ? contour cutting; or ? a combination of the above. The material to be cut may be supported or transported by: ? a fixed table; ? a shuttle table; ? a conveyor; ? a turntable; ? rollers; ? mandrel; or ? a combination of the above. Cutting can be either manual or automatic. Cutting tools can be: ? smooth-edged or toothed bandknives; ? cutting wires. Movement of the cutting tool can be either oscillating or continuous in one direction. This European Standard does not apply to: ? laser and water jet cutting; ? hot wire cutting; ? wood, metal and food cutting machines. The safety requirements for the additional hazards arising from the interaction between bandknife cutting machines and ancillary equipment, especially loading and unloading devices, are specified. The safety requirements for the ancillary equipment itself are not specified. This European Standard covers machines used for cutting plastics and rubber having a cellular or compact structure. However, it may also be applied when these machines are used for cutting other materials, for example textiles, fibres and mineral wool, if cutting these materials does not create additional hazards. This document is not applicable to bandknife cutting machines manufactured before the date of its publication as an EN.

Plastics and rubber machines - Bandknife cutting machines for block foams - Safety requirements

EN 1114-1:2011 塑料和橡胶机,挤出机和挤出线-第1部分:安全要求挤出机

This European Standard specifies all significant hazards, hazardous situations and events relevant to all types of screw extruders for plastics and rubber, when they are used as intended and under conditions of misuse which are foreseeable by the manufacturer (see Clause 4).This European Standard additionally covers the following feeding systems: hoppers; single roller feed; double roller feed; crammer feeder; and the following ancillary equipment which form part of or are attached to the extruder: screen changers; melt/gear pumps; melt pipes and adaptors; static mixers; extruder head that give initial shape to the extruded material. NOTE Metering devices are not covered byThis standard.This European Standard does not deal with hazards caused by the processing of materials and which may lead to a risk of fire or release of health hazardous materials. An extruder conforming toThis document is not regarded as a pressure vessel as defined in the Pressure Equipment Directive 97/23/EC. Extruders usually do not produce explosive atmospheres. Where materials are processed, which may cause an explosive atmosphere, the Directive 94/9/EC on the Equipment intended for use in Potentially Explosive Atmospheres (ATEX) should be applied. Explosion hazards are not dealt with inThis document.This European Standard is not applicable to extruders which are manufactured before the date of its publication as EN.

Plastics and rubber machines - Extruders and extrusion lines - Part 1: Safety requirements for extruders

DIN EN 12012-2:2010 橡胶和塑料机.粉碎机.第2部分:绞线成球机的安全性要求.德文版本EN 12012-2-2001+A2-2008

This standard specifies the essential safety requirements applicable to the design and construction of strand pelletisers used for plastics and rubber and fed continuously by an extruder or a reactor.

Plastics and rubber machines - Size reduction machines - Part 2: Safety requirements for strand pelletisers; German version EN 12012-2:2001+A2:2008

DIN EN 12301:2010 橡胶和塑料机械.压延机.安全性要求.德文版本EN 12301-2000+A1-2008

This Eropean Standard specifies safety requirements relating to the design and construction of multi-roll calenders intended for the processing of rubber or plastics. This standard concerns the calender alone including all components fixed to its frame. The following machines are excluded: - Two-roll calenders forming an integral unit with an extruder (roller head) - Two- or three-roll polishing, laminating or embossing units ( which are not calenders) installed downstream of extruders in film processing lines.

Plastics and rubber machines - Calenders - Safety requirements; German version EN 12301:2000+A1:2008

ISO 28238:2010 压缩模具和注射模具.浇注系统部件

This International Standard specifies the characteristics of components of gating systems used in injection moulds for the processing of thermoplastics, thermosetting plastics and elastomers. These are gating systems for solidifying sprues for externally heated gating systems, internally heated gating systems and cold runner gating systems. The purpose of this International Standard is to establish coherent terms for the different gating systems in professional terminology.

Compression and injection moulds - Components for gating systems

DIN EN 12012-1:2010 塑料和橡胶机械.粉碎机.第1部分:叶片式造粒机的安全要求.德文版本EN 12012-1-2007+A1-2008

This standard specifies the essential safety requirements applicable to the design and construction of blade granulators used to reduce objects and materials made from plastics and rubber into granules.

Plastics and rubber machines - Size reduction machines - Part 1: Safety requirements for blade granulators; German version EN 12012-1:2007+A1:2008