87.020 涂料涂覆工艺 标准查询与下载

LST EN ISO 16276-1:2007 通过防护漆系统对钢结构的腐蚀防护 涂层附着力/内聚力（断裂强度）的评估和验收标准 第1部分：拉拔测试（ISO 16276-1:2007）

Corrosion protection of steel structures by protective paint systems - Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating - Part 1: Pull-off testing (ISO 16276-1:2007)

DS/EN ISO 16276-1:2007 通过防护漆系统对钢结构的腐蚀保护 涂层的附着力/内聚力（断裂强度）的评估和验收标准 第1部分：拉脱测试

This part of ISO 16276 specifies procedures for assessing the fracture strength of a protective paint coating of any thickness on a steel substrate of thickness not less than 10 mm. The procedures given in this part of ISO 16276 are based on methods used with different types of pull-off test equipment. The results obtained using such different types of equipment are not comparable.NOTE 1 Substrates of less than 10 mm in thickness can be tested if they are strengthened by the sandwich technique (see ISO 4624) or by the nature of the structure (e.g. I-beam or backing-plate). Otherwise, test panels with a thickness of at least 10 mm coated in the same way as t

Corrosion protection of steel structures by protective paint systems - Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating - Part 1: Pull-off testing

EN ISO 12944-5:2007 涂料和清漆.防护涂料系统对钢结构的腐蚀防护.第5部分:防护涂料系统

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 5: Protective paint systems (ISO 12944-5:2007)

SANS 10305-2:2005 建筑物的刷涂．第2部分：涂料施涂和缺陷

Covers the preparation of surfaces before repainting and good practice in applying paint.

Painting of buildings Part 2: Paint application and defects

SANS 10305-4:2005 建筑物的刷涂．第4部分：墙壁，天花板和包层的刷涂

Covers the individual characteristics and preparation (before painting) of plaster, concrete, brick and stone surfaces of walls, ceilings and cladding, and the choice and application of paint to these surfaces.

Painting of buildings Part 4: Painting of walls, ceilings and cladding

SANS 10305-6:2005 建筑物的刷涂．第6部分：木材的刷涂

Covers the nature and preparation, for purposes of painting, of wood surfaces, and the choice and application of paint to such surfaces.

Painting of buildings Part 6: Painting of wood

SANS 10305-5:2005 建筑物的刷涂．第5部分：屋顶和钢结构的刷涂

Covers the nature and preparation, before painting, of roofs and steel structures, the choice of paint for these surfaces and its application.

Painting of buildings Part 5: Painting of roofs and steel structures

SANS 5044:2005 色漆和清漆．色漆的喷涂性能

Specifies a method for assessing spray application properties and the flow characteristics of paints when the paints are applied over relatively large areas. It can also be used to assess other properties such as recoating, lapping and retraction from sh

Paints and varnishes - Spraying properties of paints

KS F 9001-2004 混凝土用环氧树脂防水、防潮涂料涂覆施工标准

이 규격은 콘크리트 구조물의 방수ㆍ방식을 목적으로 콘크리트 내외면에 도포하는 에폭시 수

Standard coating method of epoxy resin paints for waterproof and anticorrosion of concrete structures

ISO 19840:2004 色漆和清漆.用防护漆系统对钢结构的腐蚀防护.粗面上干膜厚度的测量和验收标准

This International Standard specifies a procedure for the verification of dry film thickness against nominal dry film thickness on rough surfaces, including the adjustment of the instruments used, the definition of inspection areas, sampling plans, measurement methods and acceptance/rejection criteria. For the purposes of this standard, any specified thickness is taken to be nominal as defined in ISO 12944-5 and the dry film thickness is the typical thickness above the peaks of the surface profile. The procedure described in this International Standard is based on the use of instruments of the permanent magnet and inductive magnet type. Instruments are adjusted to zero and a known thickness on a smooth surface. Measurements taken on a coating on a roughened steel substrate will therefore be higher than the actual value above the peaks of the profile. The thickness of the dry film above the peaks of the profile is defined as the instrument reading minus an appropriate correction value. The dry film thickness is obtained by using the appropriate correction value applied to readings based on adjustment on a smooth, flat, steel surface. Where individual readings, based on adjustment on a smooth, flat steel surface without the use of correction values, are specified or agreed, it is important to recognise that this method does not conform with this International Standard. This standard is applicable if the nominal dry film thickness is 40 μm or greater. NOTE If the nominal thickness is less than the surface roughness of the substrate the uncertainty of the measurement will increase.

Paints and varnishes - Anticorrosion of steel structures by painting systems - Measurement and acceptance criteria of the thickness of a dry film on rough surfaces (Second edition)

ASTM D4537-04 在核设施中进行涂层工作检验的人员资格鉴定和认证程序的制定指南

1.1 This guide delineates the requirements for development of procedures for the qualification of personnel who perform inspection of coating work. These activities are accomplished to verify conformance to specified requirements for nuclear facility coating work whose satisfactory performance is required in order not to compromise safety-related coating systems.1.2 This guide provides a uniform interpretation of the intent of the requirements in ANSI/ASME N45.2.6 for the inspection of coating work in nuclear facilities.1.3 This guide meets the intent of ANSI/ASME NQA-1.1.4 It is the intent of this guide to provide a recommended basis for qualification, not to mandate a singular basis for all qualifications. Variations or simplifications of the qualifications described in this guide may be appropriate for special coating work other than safety-related coating systems. Similarly, the qualification and certification process might be abbreviated for work of minor scope such as touch-up. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Establishing Procedures to Qualify and Certify Personnel Performing Coating Work Inspection in Nuclear Facilities

ASTM D6491-99(2003) 在干热试验中预应力预浸金属的耐老化性评价标准实践

Standard Practice for Evaluation of Aging Resistance of Prestressed Prepainted Metal In a Dry Heat Test

ISO 20340:2003 色漆和清漆.用于近海建筑及相关结构的保护性涂料系统的性能要求

1 This International Standard specifies the performance requirements for the protection, by protective paint systems, of new offshore and related structures exposed to the offshore atmosphere, as well as those immersed in sea or brackish water. Such structures are exposed to environments of corrosivity category C5-M and immersion category Im2 as defined in ISO 12944-2:1998, with special stresses as given in 4.3 and Annex B of ISO 12944-2:1998. It can also be used for other structures, provided that the selected paints or protective paint systems comply with this International Standard. Only new work and any repairs necessary before start-up are included. This International Standard places emphasis on high-durability paint systems, with the aim of minimizing maintenance, and hence reducing safety considerations and environmental impact. 2 This International Standard includes the following: — the test methods to be used to determine the composition of the separate components of the protective paint system; — the laboratory performance test methods for the assessment of the likely durability of the protective paint system; — the criteria to be used to evaluate the results of performance tests. The fields of application are specified in Clause 4. For reference purposes, some typical examples of protective paint systems which have been used successfully offshore are included in Table 3.

Paints and varnishes - Performance requirements for protective paint systems for offshore and related structures

SANS 6280:2003 油漆和清漆．应用浸渍

Describes a method for obtaining a uniform film by means of dipping. Dipping properties of a coating can also be determined.

Paints and varnishes - Application by dipping

SANS 5037:2003 色漆和清漆．刮漆刀的使用

Describes a method for obtaining a uniform film by means of a hand-held or a motor-driven applicator blade.

Paints and varnishes - Application by applicator blade

ASTM D5531-94(2003) 涂料颜色和几何外观物理产品标准的制备 维护和分配标准指南

Standard Guide for Preparation, Maintenance, and Distribution of Physical Product Standards for Color and Geometric Appearance of Coatings

NP EN ISO 8502-9:2003 在使用油漆以及类似物质之前来制作钢制衬底．表面清洗测试．第9部分：水中可溶性盐的测量方法（ISO 8502-9-1998）

Esta parte da Norma descreve um método de campo para avalia??o da densidade total de vários sais solúveis em água (na sua maioria cloretos e sulfatos) nas superfícies de a?o, antes e/ou depois da prepara??o da superfície. As densidades individuais dos cloretos, sulfatos, etc, na superfície, n?o podem ser determinadas por este método. Este método avalia apenas os contaminantes iónicos. Estes representam a maior parte da contamina??o.

Preparation of steel substrates before application of paints and related products Tests for assessment of surface cleanliness Part 9:Field method for the conductometric determination of water-soluble salts (ISO 8502-9-1998)

LST EN ISO 8502-9:2002 涂漆和相关产品前钢基材的准备 表面清洁度评估试验 第9部分：水溶性盐电导测定的现场方法（ISO 8502-9:1998）

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 9: Field method for the conductometric determination of water-soluble salts (ISO 8502-9:1998)

LST EN ISO 8501-2:2002 涂漆和相关产品前钢基材的预处理 表面清洁度的目视评估 第2部分：局部去除先前涂层后先前涂覆的钢基材的制备等级（ISO 8501-2:1994）

Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 2: preparation grades of previously coated steel substrates after localized removal of previous coatings (ISO 8501-2:1994)

LST EN ISO 11126-7:2002 涂漆和相关产品前钢基材的准备 非金属喷砂清理磨料的规范 第7部分：熔融氧化铝（ISO 11126-7:1995）

Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 7: Fused aluminium oxide (ISO 11126-7:1995)