87.080 墨水、油墨 标准查询与下载

ASTM D6688-20 用三明治技术测定印刷品对液体化学物质相对电阻的标准实施规程

1.1 This practice covers the evaluation of the relative resistance of printed matter to liquid chemicals, as evidenced by lack of discoloration, bleeding, or loss of gloss. 1.2 This practice utilizes a sandwich procedure similar in principle to ISO/TC 130 N 589. Spotting or immersion procedures are covered in Test Methods D1308, D1647, and D2248. 1.3 This practice is applicable to prints on any flat substrate including paper, paperboard, metallic foil, metal plate, and plastic films, and produced by any printing process including letterpress, offset lithography, flexography, gravure, silk screen, and non-impact. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Relative Resistance of Printed Matter to Liquid Chemicals by a Sandwich Technique

ASTM D4942-20 实验室混合器中平版印刷油墨和载体吸水率的标准试验方法

1.1 These test methods cover two procedures for determining the amount of water picked up by lithographic printing inks in a laboratory mixer. 1.2 Test Method A covers single-point water pickup; Test Method B covers the rate of water pickup. Both test methods are applicable to any printing ink and vehicle intended for the lithographic printing process. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Water Pickup of Lithographic Printing Inks and Vehicles in a Laboratory Mixer

ASTM D8020-15(2020) 水性油墨和油墨车辆的冻融粘度稳定性的标准测试方法

1.1 This test method covers a procedure for evaluating the effect of freeze-thaw cycling on the properties of water-based inks and ink vehicles. 1.2 This test is based on a similar standard test for coatings; Test Method D2243. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Freeze-Thaw Viscosity Stability of Water-Based Inks and Ink Vehicles

ASTM D4713-12(2020) 热固和液体印刷油墨系统非挥发物含量的标准测试方法

1.1 These test methods cover the determination of weight content of nonvolatile matter in two types of printing inks. 1.2 Test Method A is applicable to heatset-type printing inks and resin solutions; solvents in such systems typically have initial boiling points in the range from 240 to 275°C (470 to 535°F) and vapor pressures less than 0.2 mm Hg. 1.3 Test Method B is applicable to liquid-type printing inks and vehicles based on aqueous or organic solvents that evaporate readily at ordinary room temperatures. NOTE 1—Test Method A (for heatset systems) specifies a specimen film thickness that is much thinner than those produced by related test methods; one exception is Test Method B in Test Methods D1259, which is recommended as a referee test. NOTE 2—Test Method B (for liquid ink systems) is similar to Test Method D2369 except that a solvent is not required for spreading the test specimen. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Nonvolatile Content of Heatset and Liquid Printing Ink Systems

ASTM D5909-20 用角鲨烯抗性测定氧化干燥印刷油墨干燥时间的标准试验方法

1.1 This test method covers the procedure for determining the drying time of oxidative-drying printing inks (also referred to as “sheetfed inks”) by squalene resistance of printed ink films. 1.2 This test method is applicable to all paste inks that dry primarily by oxidation regardless of the substrate on which they are printed. With appropriate changes in the test fluid, it may also be used with paste inks that dry by other mechanisms, such as heatset or ultraviolet light. 1.3 This test method utilizes a modified rub tester and is intended to serve as a “referee” procedure when laboratories, using less rigorous test procedures (see Appendix X1), cannot agree on their results. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Drying Time of Oxidative-Drying Printing Inks by Squalene Resistance

QB/T 5487-2020 胶印油墨乳化的测定方法

Determination method for emulsification of offset printing ink

QB/T 5477-2020 装饰纸水性印刷油墨

Decorative paper water-based printing ink

QB/T 5489-2020 喷墨墨水储存稳定性的检验方法

Testing method for storage stability of inkjet ink

QB/T 5474-2020 柔版塑料薄膜复合油墨

Flexographic plastic film composite ink

QB/T 5488-2020 液体油墨复合强度的测定方法

Method for determination of composite strength of liquid ink

QB/T 5478-2020 紫外发光二极管光固化胶印油墨

UV light-emitting diode light-curing offset printing ink

T/ZZB 1552-2020 环保型植物油基胶印油墨

本标准规定了环保型植物油基胶印油墨的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。本标准适用于以植物油、颜料、树脂等原材料加工制成的胶印油墨。

Environmentally vegetable oil-based offset printing ink

T/CSSGA 1026-2019 丙烯画颜料

本标准规定了丙烯画颜料的术语定义、分类、要求、试验方法、检验规则和标志、包装、运输、贮存。

Acrylic colour

T/CWIA 1006-2019 记号笔通用测试液

记号笔通用测试液主要技术内容包括外观、黏度、表面张力、pH、密度和粒度等6项性能指标。附录A提供了测试液配制方法。

General testing fluid for marking pens

IEC 62899-204:2019 印刷电子.第204部分:材料.绝缘体油墨.绝缘体油墨和印刷绝缘层性能的测量方法

Printed electronics - Part 204: Materials - Insulator ink - Measurement methods of properties of insulator inks and printed insulating layers

IEC 62899-202-3:2019 印刷电子.第202-3部分:材料.导电油墨.导电膜片电阻的测量.非接触法

This part of IEC 62899 defines terms and specifies a standard method for the measurement of the sheet resistance of printed conductive films using a contactless eddy-current method.

Printed electronics - Part 202-3: Materials - Conductive ink - Measurement of sheet resistance of conductive films - Contactless method

T/CTES 1015-2019 热转移印花用分散染料水性墨

本标准规定了转移印花用分散染料水性墨的要求、试验方法、检验规则、标志、标签、包装、运输和贮存。 本标准适用于在转移纸凹版印刷机上使用的热升华分散染料水性墨。

Disperse dye water-based ink for thermal transfer printing

ASTM D6487-10(2019) 用手动实验室平板印刷机制备糊状印刷油墨印刷品的标准实施规程

1.1 This practice covers the procedure for preparing prints of paste inks using a hand operated flat-bed laboratory proof press. The initial method was developed by the National Printing Ink Research Institute.2 1.2 This practice is applicable to the preparation of singlecolor solid-area prints by the dry offset process (also known as Letterset) on a flat substrate such as paper or metal. It can readily be adapted to print by direct letterpress.3 NOTE 1—The proofing press described in this practice can also be used with printing gages in accordance with Practice D6846. 1.3 This practice is applicable primarily to lithographic and letterpress inks that dry by oxidation or penetration. With the addition of appropriate drying or curing equipment, it is also applicable to other systems such as heat-set or energy-curable. 1.4 The instructions in this practice are intended to minimize the within-print and among-operator variability inherent in hand operations. 1.5 This practice does not measure the actual film thickness on the print, but evaluates film thickness equivalence by visual or instrumental comparisons of reflection density. 1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the users of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautions are given in Section 7. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparing Prints of Paste Printing Inks Using a Hand Operated Laboratory Flat-Bed Press

ASTM D4040-10(2019) 颚式粘度计粘贴印刷和车辆流变特性的标准试验方法

1.1 This test method covers the procedure for determining the falling-rod viscosity and degree of non-Newtonian behavior of printing inks, vehicles, and similar liquids that are essentially nonvolatile and unreactive under ordinary room conditions. 1.2 For printing inks, which are typically non-Newtonian, this test method is applicable in the apparent viscosity range from about 10 to 300 P at a shear rate of 2500 s−1 . For Newtonian liquids, the applicable viscosity range is about 10 to 1000 P (1 P = 0.1 Pa·s). 1.3 This test method uses a falling-rod viscometer in which shear conditions are altered by manually adding weight to the rod. A fully automatic instrument is described in Test Method D6606. 1.4 This test method, as does Test Method D6606, bases calculations on the power law model of viscosity. ISO 12644 covers not only the power law but also the Casson and Bingham models. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 8. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Rheological Properties of Paste Printing and Vehicles by the Falling-Rod Viscometer

ASTM D7680-10(2019) 通过电机驱动的打印测试仪准备粘贴印刷油墨的标准实践

Standard Practice for Preparing Prints of Paste Printing Inks by a Motor-Driven Printability Tester