91.100.50 粘合料、密封材料 标准查询与下载

ASTM D5710/D5710M-22 特立尼达湖改性沥青标准规范

1.1 This specification covers Trinidad Lake modified asphalt for use in the construction of pavements. 1.2 This specification covers the following penetration grades: 40–55 60–75 80–100 120–150 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Trinidad Lake Modified Asphalt

ASTM D4402/D4402M-15(2022) 用旋转粘度计在高温下测定沥青粘度的标准试验方法

1.1 This test method outlines a procedure for measuring the apparent viscosity of asphalt from 38 to 260 °C [100 to 500 °F] using a rotational viscometer and a temperature-controlled thermal chamber for maintaining the test temperature. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See 10.6 for specific precautionary information. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Viscosity Determination of Asphalt at Elevated Temperatures Using a Rotational Viscometer

ASTM D3746/D3746M-85(2022) 沥青屋面系统抗冲击性的标准试验方法

1.1 This test method covers the determination of the resistance of bituminous roofing systems to impact loads at any desired temperature, with a missile of the weight, size, and shape specified herein. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 6. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Impact Resistance of Bituminous Roofing Systems

ASTM D2872-22 热和空气对沥青粘合剂移动膜影响的标准试验方法（滚动薄膜烘箱试验）

1.1 This test method is intended to measure the effect of heat and air on a moving film of semi-solid asphaltic materials. The effects of this treatment are determined from measurements of the selected properties of the asphalt before and after the test. 1.2 The values stated in inch-pound units are to be regarded as the standard. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt Binder (Rolling Thin-Film Oven Test)

ASTM D7906-22 用甲苯和旋转蒸发器从溶液中回收沥青粘合剂的标准实施规程

1.1 This practice is intended to be used to recover asphalt from a solvent using the rotary evaporator to ensure that changes in the asphalt properties during the recovery process are minimized. 1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Recovery of Asphalt Binder from Solution Using Toluene and the Rotary Evaporator

ASTM D4074/D4074M-11(2022) 屋顶样品沥青集料混合物中沥青和集料含量的标准试验方法

1.1 This test method covers the determination of the bitumen content of adhered aggregate surfacing on a roof, and the approximate mass per unit area of the flood coat and adhered aggregate. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Bitumen and Aggregate Content of Bitumen-Aggregate Mixtures From Roofing Samples

T/CECS 10185-2022 装配式建筑用密封胶

本文件规定了装配式建筑用密封胶的术语和定义，分类和标记，要求，试验方法，检验规则，标志、包装、运输和贮存等。

Sealant for prefabricated buildings

T/ZZB 2617-2022 普通型糊状壁纸（布）胶粘剂

本文件规定了普通型糊状壁纸（布）胶粘剂的术语和定义、分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存以及质量承诺。 本文件适用于室内壁纸、壁布胶粘用普通型水性糊状胶粘剂（以下简称壁纸（布）胶）和配套用基膜（以下简称基膜）。

Ordinary paste wallcovering adhesive

ISO 4781:2022 建筑和土木工程密封剂.使用寿命的测定

Building and civil engineering sealants — Determination of application life

ASTM D4068-17(2022) 隐蔽式水密封膜用氯化聚乙烯（CPE）薄板的标准规范

1.1 This specification covers flexible chlorinated polyethylene (CPE) sheeting which is used without mastic, bedding, or coating for construction of concealed water-containment membranes in applications where there is potential for costly secondary damage from leakage, and where very long-term reliable performance is essential. Examples are fountains, pools, planters, shower and safe pans, tile tubs, and similar installations where the membrane is inaccessible once construction is complete. Included are requirements for composition, strength and toughness, test methods, workmanship criteria, and methods of marking. 1.2 Manufacturers have the option to use recycled materials in this product. Recycled materials must be in accordance with the requirements in Section 4. 1.3 The test methods used to characterize the sheeting are intended to ensure quality and performance and are not necessarily adequate for design purposes. Test methods have been selected to be conducted primarily with liquids that simulate the environments to which the membrane will be subjected during actual installation and use. 1.4 This specification does not cover water-containment membranes exposed in use to ultraviolet light or direct sunlight. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. NOTE 1—There is no known ISO equivalent to this standard. 1.6 The following safety hazards caveat pertains only to the test method portion, Section 14, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane

BS ISO 4784:2022 建筑和土木工程密封剂 表面固化时间的测定

What is ISO 4784 - surface cure time of sealants about? ISO 4784 is an International Standard that discusses building and civil engineering sealants. ISO 4784 provides technical terms for sealants to develop a better understanding. ISO 4784 specifies a method for the determination of the surface cure of one- and multi-component sealants. Who is ISO 4784 - surface cure time of sealants for? ISO 4784 on the determination of surface cure time of sealants is useful for: The construction industry Builders / real estate developers / architects Civil / building / construction engineers Sealant manufacturers Government and private entities

Building and civil engineering sealants. Determination of surface cure time

T/QGCML 260-2022 UPVC型材共挤用PVC复合胶条及其制备方法

本文件规定了UPVC型材共挤用PVC复合胶条及其制备方法的术语和定义、构成、制备方法、要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于UPVC型材共挤用PVC复合胶条的生产和制备。

PVC composite rubber strip for co-extrusion of UPVC profiles and preparation method thereof

ISO 11617:2022 建筑和土木工程密封剂.静态固化试样暴露于人工风化和机械循环后弹性防风雨密封剂的内聚性和外观变化的测定

This documentspecifies laboratoryexposure procedures for determining the effects of cyclic movement and artificial weathering on cured, elastic weatherproofing joint sealants (one- or multi-component).

Building and civil engineering sealants — Determination of changes in cohesion and appearance of elastic weatherproofing sealants after exposure of statically cured specimens to artificial weathering

ASTM C719-22 在循环运动（霍克曼循环）下弹性接缝密封剂的附着力和内聚性的标准试验方法

1.1 This test method is an accelerated laboratory procedure for evaluating the performance of a building sealant in a test configuration that is subjected to water immersion, cyclic movement, and temperature change.3 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)

ISO 4784:2022 建筑和土木工程密封剂.表面固化时间的测定

Building and civil engineering sealants — Determination of surface cure time

T/CBMF 166-2022 室内装饰装修用美缝剂

本文件规定了室内装饰装修用美缝剂(简称美缝剂)的分类、代号与标记、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于陶瓷砖、石材、马赛克等室内铺贴装饰预留缝隙具有填充和装饰效果的嵌缝材料。

Reaction resin grout for indoor decorating

ASTM C731-15(2022) 乳胶密封剂包装老化后可挤压性的标准试验方法

1.1 This test method covers a laboratory procedure for the determination of extrudability of latex sealants after freezethaw and heat cycling. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—Currently there is no ISO standard similar to this test method. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Extrudability, After Package Aging, of Latex Sealants

ASTM C1246-17(2022) 热老化对固化后弹性密封剂的重量损失、开裂和粉化影响的标准试验方法

1.1 This test method covers a laboratory procedure for determining the effects of heat aging on weight loss, cracking and chalking of elastomeric joint sealants (single and multicomponent) for use in building construction. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 The committee having jurisdiction for this specification is not aware of any similar ISO standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants After Cure

ASTM C736-12(2022) 乳胶密封剂的延伸恢复率和附着力的标准试验方法

1.1 This test method covers a laboratory procedure for the determination of the extension-recovery and adhesion of latex sealants. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—A related ISO standard is ISO 7389. Users should compare to determine how the ISO standard differs from this test method. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Extension-Recovery and Adhesion of Latex Sealants

ASTM C510-16(2022) 单组分或多组分接缝密封剂染色和颜色变化的标准试验方法

1.1 This test method covers an accelerated laboratory procedure to determine if a sample of a joint sealant will stain the substrate when in contract with masonry, concrete, or stone (such as marble, limestone, sandstone, and granite). This test method also is intended to determine whether the sealant itself will change in color when exposed to the weather. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants