93.030 外部污水排放系统 标准查询与下载

DIN EN 1123-2:2007 废水系统用带龙头和套管的纵向焊接热浸镀锌钢管的管道和配件.第2部分:尺寸

This European Standard applies to pipes and fittings of lingitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems. It specifies dimensions and tolerances for pipes, fittings, pipe connectors and seals and establishes a system of designations for the different pipe and fitting types that conform to the stated requirements. This standard is only valid in connection with EN 1123-1. This standard does not apply to the marking of products. EN 1123-1 applies to the marking.

Pipes and fittings of longitudinally welded hot-dip galvanized steel tube with spigot and socket for waste water systems - Part 2: Dimensions; German version EN 1123-2:2006+A1:2007

DS/CEN/TS 14758-2:2007 非压力地下排水和污水处理用塑料管道系统 含矿物改性剂的聚丙烯（PP-MD） 第2部分：合格评定指南

This European Technical Specification gives guidance for the assessment of conformity to be included in the manufacturer's quality plan as part of the quality system.This Technical Specification includes: a) requirements for materials, components, joints and assemblies given in EN 14758-1;b) requirements for the manufacturer's quality system; NOTE 1: It is recommended that the quality system conforms to EN ISO 9001 [1].c) definitions and procedures to be applied if third party certification is involved.NOTE 2: If third party certification is involved, it is recommended that the certification body is accredited to EN 45011 [2] or EN 45012 [3], as applicable.

Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifier(s) (PP-MD) - Part 2: Guidance for the assessment of conformity

NF P16-353-1:2007 非压力地下排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)结构壁管道系统.第1部分:一般要求和性能特征

Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1 : general requirements and performance characteris

NF P16-353-2:2007 非压力地下排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)结构壁管道系统.第2部分:A型带光滑内外表面的管道和配件用规范

Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2 : specifications for pipes and fittings with smoot

LST EN 13566-7-2007 地下无压排水和污水管网改造用塑料管道系统 第7部分：螺旋缠绕管内衬

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 7: Lining with spirally-wound pipes

DIN EN 13476-1:2007 无压地下排水和污水用塑料管系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)的结构壁管系统.第1部分:一般要求和性能特征

This European Standard, together with EN 13476-2 and EN 13476-3, specifies the definitions and general requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene(PP) and polyethylene(PE) structured-wall piping system that are to be used for non-pressure underground drainage and sewerage systems. This standard is applicable to: a) strutured-wall pipes and fittings, which are to be used buried in the ground outside a building structure only; reflected by the marking of products by"U"; b) structured-wall pipes and fittings, which are to be used buried in the ground both outside(application area code"U") and within a building structure(application area code"D"); reflected in the marking of products by"UD". In cojunction with EN 13476-2 and EN 13476-3 it is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints, as well as welded and fused joints. This part specifies general aspects and gives guidance concerning a national selection of requirement levels and classes where part 2 and part 3 of this standard provide options. EN 13476-2 and 13476-3 specify material characteristics, dimensions and tolerances, test methods, test parameters and requirements for pipes with smooth internal and external surfaces, Type A, and pipes with smooth internal and profiled external surfaces, Type B. This standard, together with EN 13476-2 and EN 13476-3, covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes and tolerance classes and offers recommendation concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. NOTE 2 Pipes,n fittings and other components conforming to any plastic product standards referred to in clause 2 can be used with pipes and fittings conforming to this standard, when they conform to the requirements for joint dimensions given in part 2 and part 3 of this standard and to the performance requirements given in Clause 9. NOTE 3 For dimension larger than DN 1200 OD/ID this document may serve as general guideline regarding appearance, colour, physical and mechanical characteristics as well as performance requirements.

Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: General requirements and performance characterist

DIN EN 13476-2:2007 无压地下排水和污水用塑料管系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)结构壁管系统.第2部分:A型、有平滑内外表面的管和配件及系统用规范

This part of EN 13476, together with EN 13476-1, specifies the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene(PP) and polyethylene(PE) structured-wall piping system that are intended to be used for non-pressure underground drainage and sewerage systems. This part is applicable to pipes and fittings with smooth internal and external surfaces, designated as Type A. It specifies test methods and test parameters as well as requirements. This part is applicalbe to: a) strutured-wall pipes and fittings, which are intended to be used buried underground outside the building structure;reflected in the marking of products by"U"; b) structured-wall pipes and fittings, which are intended to be used buried underground both outside(application area code"U") and within a building structure(application area code"D"); reflected in the marking of products by"UD". This part is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints. This part covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes, application classes, and tolerance classes and gives recommendations concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. NOTE 2 For dimension larger than DN 1200 OD/ID this document may be applied regarding appearance, colour, physical and mechanical characteristics as well as performance requirements.

Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth

DIN EN 13476-3:2007 无压地下排水和污水塑料管系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)结构壁管系统.第3部分:B型、有平滑内外表面的管和配件及系统规范

This part of EN 13476, together with EN 13476-1, specifies the definitions and requirements for pipes, fittings and the system based in unplasticized poly(vinyl chloride)(PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are intended to be used for non-pressure underground drainage and sewerage systems. This part is applicable to pipes and fittings with smooth internal and profiled external surfaces, designated as Type B. It specifies test methods and test parameters as well as requirements. This part is applicable to: a) structured-wall pipes and fittings, which are intended to be used buried underground outside the building structure, reflected in the marking of products by "U"; b) structured-wall pipes and fittings, which are intended to be used buried underground both outside (application area code "U") and within the building structure (application area code "D"), reflected in the marking of products by "UD". This part is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joins as well as welded and fused joints. This part covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes, application classes, and tolerance classes and gives recommendations concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections form these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. NOTE 2 For dimensions larger than DN 1200 OD/ID this document may be applied regarding appearance, colour, physical and mechanical characteristics as well as performance requirements.

Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Specifications for pipes and fittings with smooth

BS EN 13476-2:2007 无压地下排水和污水塑料管系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)结构壁管系统.A型、有平滑内外表面的管和配件及系统用规范

This part of EN 13476, together with EN 13476-1, specifies the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are intended to be used for non-pressure underground drainage and sewerage systems. This part is applicable to pipes and fittings with smooth internal and external surfaces, designated as Type A. It specifies test methods and test parameters as well as requirements. This part is applicable to: a) structured-wall pipes and fittings, which are intended to be used buried underground outside the building structure; reflected in the marking of products by “U”; b) structured-wall pipes and fittings, which are intended to be used buried underground both outside (application area code “U”) and within the building structure (application area code “D”); reflected in the marking of products by “UD”. This part is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints. This part covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes, application classes, and tolerance classes and gives recommendations concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. NOTE 2 For dimensions larger than DN 1200 OD/ID this document may be applied regarding appearance, colour, physical and mechanical characteristics as well as performance requirements.

Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Specifications for pipes and fittings with smooth interna

BS EN 13476-1:2007 无压地下排水和污水塑料管系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)结构壁管系统.一般要求和性能特性

This European Standard, together with EN 13476-2 and EN 13476-3, specifies the definitions and general requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are to be used for non-pressure underground drainage and sewerage systems. This standard is applicable to: a) structured-wall pipes and fittings, which are to be used buried in the ground outside a building structure only; reflected by the marking of products by “U”; b) structured-wall pipes and fittings, which are to be used buried in ground both outside (application area code “U”) and within a building structure (application area code “D”); reflected in the marking of products by “UD”. In conjunction with EN 13476-2 and EN 13476-3 it is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints, as well as welded and fused joints. This part specifies general aspects and gives guidance concerning a national selection of requirement levels and classes where part 2 and part 3 of this standard provide options. EN 13476-2 and EN 13476-3 specify material characteristics, dimensions and tolerances, test methods, test parameters and requirements for pipes with smooth internal and external surfaces, Type A, and pipes with smooth internal and profiled external surfaces, Type B. This standard, together with EN 13476-2 and EN 13476-3, covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes and tolerance classes and offers recommendations concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. NOTE 2 Pipes, fittings and other components conforming to any plastic product standards referred to in clause 2 can be used with pipes and fittings conforming to this standard, when they conform to the requirements for joint dimensions given in part 2 and part 3 of this standard and to the performance requirements given in Clause 9. NOTE 3 For dimensions larger than DN 1200 OD/ID this document may serve as general guideline regarding appearance, colour, physical and mechanical characteristics as well as performance requirements.

Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - General requirements and performance characteristics

DIN EN 13508-2 Corrigendum 1:2007 建筑物外部排水和排污系统的条件. 第2部分: 目视检验编码系统. 英文版本DIN EN 13508-2: 2003-09勘误表1

Conditions of drain and sewer systems outside buildings-Part 2:Visual inspection coding system Corrigendum 1 to English version of DIN EN 13508-2:2003-09

DIN EN 13566-7:2007 地下非压力排水和排污网的修缮用塑料管道系统.第7部分:螺旋缠绕管内衬

This part of EN 13566,read in conjunction with EN 13566-1,specifies requirements and test methods for pipes that are formed on site bu spirally winding and jointing a pre-manufactured profoled plastics strip using a dedicated winding machine in front of the open end of an existing pipeline(e.g.in a manhole).The pipes thus formed are simultaneously insered into the existing pipeline by the winding forces. lt covers spirally-wound pipes of a fixed diameter made of profilek plastics strips of unplasticized poly(vinylchloride)(PVE-U) with an integral locking mechanism .These spirally-wound pipes are used ofr renovatingnon-pressure drainage and sewerage networks and are fixed in place by grouting the annular space. NOTE The grouting procedure is outside the scope of this standard.

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 7: Lining with spirally-wound pipes English version of DIN EN 13566-7:2007-06

DIN EN 13508-2 Berichtigung 1:2007 建筑物外部排水和排污系统条件.第2部分:目视检验编码系统.DIN EN 13508-2-2003技术勘误

Conditions of drain and sewer systems outside buildings - Part 2: Visual inspection coding system; German version EN 13508-2:2003, Corrigenda to DIN EN 13508-2:2003-09; German version EN 13508-2:2003/AC:2007

LST EN 13476-3-2007 非压力地下排水和污水处理用塑料管道系统 未增塑聚（氯乙烯）（PVC-U）、聚丙烯（PP）和聚乙烯（PE）的结构壁管道系统 第3部分：光滑管道和管件规范

Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Specifications for pipes and fittings with smooth

LST EN 13476-2-2007 非压力地下排水和污水处理用塑料管道系统 未增塑聚（氯乙烯）（PVC-U）、聚丙烯（PP）和聚乙烯（PE）的结构壁管道系统 第2部分：光滑管道和管件规范

Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth

LST EN 13476-1-2007 非压力地下排水和污水处理用塑料管道系统 未增塑聚氯乙烯（PVC-U）、聚丙烯（PP）和聚乙烯（PE）的结构壁管道系统 第1部分：一般要求和性能特征

Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: General requirements and performance characterist

BS EN 13566-7:2007 无压地下排水管网和污水管网翻新用塑料管道系统.螺旋卷式管内衬

This part of EN 13566, read in conjunction with EN 13566-1, specifies requirements and test methods for pipes that are formed on site by spirally winding and jointing a pre-manufactured profiled plastics strip using a dedicated winding machine in front of the open end of an existing pipeline (e.g. in a manhole). The pipes thus formed are simultaneously inserted into the existing pipeline by the winding forces. It covers spirally-wound pipes of a fixed diameter made of profiled plastics strips of unplasticized poly(vinyl chloride) (PVC-U) with an integral locking mechanism. These spirally-wound pipes are used for renovating non-pressure drainage and sewerage networks and are fixed in place by grouting the annular space. NOTE The grouting procedure is outside the scope of this standard.

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Lining with spirally-wound pipes

DS/EN 14830:2007 热塑性塑料检查室和检修孔底座 抗屈曲试验方法

This European Standard specifies methods of test for the resistance of the base of thermoplastics inspection chambers and manholes to external soil and ground-water pressure after installation.NOTE This is intended as a test of the durability and structural integrity of manhole and inspection chamber bases supporting product standards prEN 13598-2 [1] and prEN 15229 [2].

Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance

BS EN 1123-2:2006+A1:2007 废水系统用带套管和座孔的径向焊接热浸镀锌钢管的管道和配件.第2部分:尺寸

This European Standard applies to pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems. It specifies dimensions and tolerances for pipes, fittings, pipe connectors and seals and establishes a system of designations for the different pipe and fitting types that conform to the stated requirements. This standard is only valid in connection with EN 1123-1. This standard does not apply to the marking of products. EN 1123-1 applies to the marking.

Pipes and fittings of longitudinally welded hot-dip galvanized steel tube with spigot and socket for waste water systems - Part 2: Dimensions

BS EN 1123-2:2006 废水系统用带龙头和插接套管的纵向焊接热浸镀锌钢管的管道和管件.第2部分:尺寸

This European Standard applies to pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems. It specifies dimensions and tolerances for pipes, fittings, pipe connectors and seals and establishes a system of designations for the different pipe and fitting types that conform to the stated requirements. This standard is only valid in connection with EN 1123-1. This standard does not apply to the marking of products. EN 1123-1 applies to the marking.

Pipes and fittings of longitudinally welded hot-dip galvanized steel tube with spigot and socket for waste water systems — Part 2: Dimensions