97.100 家用、商用和工业用加热器具 标准查询与下载

CSA/ANSI NGV 5.1-2023 住宅加油设备 (RFA)

1 Scope 1.1 General This Standard details mechanical, physical, and electrical requirements for a newly manufactured appliance that compresses natural gas for vehicles and dispenses directly into a) the vehicle natural gas fuel storage system, referred to as a residential fuelling appliance (RFA); or b) the vehicle’s activated carbon adsorbents-based adsorbed natural gas (ANG) fuel storage system, referred to as a residential fuelling appliance (RFA). This Standard applies to appliances that incorporate compression and dispensing in the same appliance. Notes: 1) Vehicle fuelling appliances (VFA) are addressed in CSA/ANSI NGV 5.2. 2) Devices dedicated only to dispensing fuel into vehicles are addressed in CSA/ANSI NGV 4.1. 1.2 Application This Standard applies to all appliances that are intended a) for natural gas only (see Clause 1.1); b) for outdoor or indoor installation in non-living spaces (e.g., garage); c) for ambient temperature not below -40 °C (-40 °F); d) for nominal voltage not exceeding 240 V AC; e) for fill pressure not exceeding specified vehicle service pressure; f) for flow rates per Clause 5of this Standard; g) for connection to residential utility gas piping systems in accordance with the requirements of the applicable Code; h) to meet installation fire safety requirements in accordance with the requirements of the applicable Code; i) for single and dual fuelling hose gas compressor packages; and j) for installation in accordance with NFPA 52 or CSA B108.1 where not in conflict with the requirements in this Standard. These requirements apply only to ANG appliances for use with vehicles that contain activated carbon- adsorbent material with an MDP/RCP ratio less than or equal to 1.5, and that have a service pressure of 6205 kPa (900 psig). 1.3 Pressure references All references to “kPa” and “psig” throughout this Standard are to be considered gauge pressures unless otherwise specified. 1.4 Resolution of conflicts In the case of conflict between this Standard and federal, national, provincial/territorial, state, or local requirements, the requirements of the authority having jurisdiction take precedence. 1.5 Units of measure This Standard contains SI (metric) units corresponding to the inch/pound quantities, the purpose being to allow the Standard to be used in SI (metric) units. If a value for a measurement and a corresponding value in other units are stated, the first stated value is to be regarded as the requirement. The given corresponding value may be approximate. If a value for a measurement and a corresponding value in other units are both specified as a quoted marking requirement, then the first stated unit or both are to be provided. Note: IEEE/ASTM SI 10 or ISO 80000-1 is used as a guide in making metric conversion from inch/pound quantities. 1.6 Terminology In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. 1.7 Alternate construction The requirements of this Standard are not intended to constrain innovation. When considering fuels, materials, designs, or constructions not specifically dealt with in this Standard, these alternatives may be evaluated as to their ability to yield levels of safety and performance equivalent to those prescribed by this Standard.

Residential fuelling appliances (RFA)

KS C IEC 60531-2022 家用和类似用途储热式电热水器性能测定方法

Methods for measuring the performance of electric thermal storage water-heaters for household and similar purposes

NB/T 10773-2021 农村住宅多能互补供热系统通用要求

General requirements for rural residential multi-energy complementary heating systems

NB/T 10771-2021 清洁采暖炉具现场测试及评价方法

On-site testing and evaluation methods for clean heating stoves

NB/T 10775-2021 农村户用储热装置

Rural household heat storage device

QB/T 5200-2017 蒸汽挂烫机

本标准规定了蒸汽挂烫机(以下简称“挂烫机”)的术语和定义、产品分类、要求、试验方法及检验规则、标志、包装、运输和贮存等。 本标准适用于在家庭和类似场合使用，额定电压不超过250 V的蒸汽挂烫机。

Garment steamer

QB/T 5134-2017 多功能电子鞋柜

本标准规定了多功能电子鞋柜的术语和定义、分类与命名、要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于额定电压220 V、额定频率50 Hz、额定输入功率不超过2 kW的家用和类似用途多功能电子鞋柜(以下简称电子鞋柜)。

Multifunction electronic shoe-cabinet

QB/T 5135-2017 毛巾保温箱

本标准规定了毛巾保温箱的术语和定义、分类与命名、要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于单相器具额定电压不超过250 V，其他器具额定电压不超过480 V的家用和类似用途，总容积不超过200 L的毛巾保温箱(以下简称毛巾箱)。

Towel insulated cabinet

CSA B214-16:2016 循环加热系统安装规范

1.1 This Code sets out the minimum provisions for the installation, extension, alteration, and renewal of hydronic heating systems. 1.2 This Code applies to open and closed hydronic heating systems. These systems include a) hydronic space heating; b) radiant heating (wall, floor, ceiling); c) convectors; d) fan coils; e) combination potable water heating and space heating (combo) systems; f) integrated mechanical systems; g) indirect-fired domestic water heating; h) pool and spa heating; i) snow and ice melt systems; and j) other auxiliary systems. 1.3 The terms “pipe” and “piping”, as well as “tube” and tubing”, are used interchangeably in this Code, unless otherwise stated. 1.4 In this Code, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Code; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Code. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. 1.5 The values given in SI units are the units of record for the purposes of this Code. The values given in parentheses are for information and comparison only.

Installation code for hydronic heating systems

ANSI/CSA NGV 5.1-2016 住宅加油设备

1.1 General This Standard details mechanical, physical, and electrical requirements for a newly manufactured appliance that dispenses natural gas for vehicles directly into the vehicle natural gas fuel storage system, referred to as a residential fueling appliance (RFA). 1.2 Application These requirements apply to appliances: a) for natural gas only (see Clause 1.1); b) for outdoor or indoor installation in nonliving spaces (e.g., garage); c) for ambient temperature not below minus 40ºC (minus 40 ºF); d) for nominal voltage not exceeding 240 Volts AC; e) for fill pressure not exceeding specified vehicle service pressure; f) for maximum inlet flow rate not exceeding 10 SCFM (17 SCMH); g) intended for connection to residential utility gas piping system in accordance with requirements of the applicable Code; h) intended to meet the installation fire safety requirements in accordance with the requirements of the applicable Code; and i) single and dual fueling hose gas compressor packages. 1.3 Pressure references All references to "kpa" and “psi” throughout this Standard are to be considered gauge pressures, unless otherwise specified. 1.4 Resolution of conflicts In the case of conflict between this Standard and Federal, National, Provincial, State, or local requirements, the authority having jurisdiction requirements take precedence. 1.5 Units of measure This Standard contains SI (Metric) units corresponding to the inch/pound quantities, the purpose being to allow the standard to be used in SI (Metric) units. If a value for a measurement and a corresponding value in other units are stated, the first stated value is to be regarded as the requirement. The given corresponding value may be approximate. If a value for a measurement and a corresponding value in other units are both specified as a quoted marking requirement, the first stated unit, or both are to be provided. Note: IEEE/ASTM SI 10 or ISO 80000-1 is used as a guide in making metric conversion from inch/pound quantities. 1.6 Terminology In this Standard, “shall” is used to express a requirement, i.e., a provision that the user shall satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Residential fueling appliances

CSA B55.1-15:2015 测量灰水热回收系统效率和压降的试验方法

1.1 Cette norme énonce les exigences applicables à la mesure de l’efficacité de la récupération de la chaleur et la perte de charge des récupérateurs de chaleur des eaux grises (RCEG) à film tombant installés à la verticale. 1.2 Cette norme vise les RCEG : a) de tous les diamètres et de toutes les longueurs ; et b) présentant des débits de l’eau potable et de l’eau grise égaux. 1.3 Dans cette norme, le terme «doit» indique une exigence, c’est-à-dire une prescription que l’utilisateur doit respecter pour assurer la conformité à la norme ; «devrait» indique une recommandation ou ce qu’il est conseillé mais non obligatoire de faire ; et «peut» indique une possibilité ou ce qu’il est permis de faire. Les notes qui accompagnent les articles ne comprennent pas de prescriptions ni de recommandations. Elles servent à séparer du texte les explications ou les renseignements qui ne font pas proprement partie de la norme. Les notes au bas des figures et des tableaux font partie de ceux-ci et peuvent être rédigées comme des prescriptions. Les annexes sont qualifiées de normatives (obligatoires) ou d’informatives (facultatives) pour en préciser l’application.

Test method for measuring the efficiency and pressure drop of gray water heat recovery systems

CAN/ANSI/AHRI 1330-2015 燃气红外加热器辐射输出的性能评级

2.1 Scope. This standard applies to Infrared Heaters that are Gas-Fired High-intensity Infrared Heaters and Gas-Fired Low-intensity Infrared Heaters with inputs up to and including 117.5 kW per burner intended for installation in and heating of outdoor or indoor spaces. 2.1.1 Exclusions. This standard does not apply to heaters that do not radiate their energy into a single measuring plane. 3 August 2022 AHRI withdrew the CAN designation from this edition

Performance Rating for Radiant Output of Gas Fired Infrared Heaters

MH/T 5110-2015 民用机场道面现场测试规程

本标准规定了民用机场道面现场检测的试验方法。本标准适用于陆地民用机场(含军民合用机场的民用部分)的工程建设阶段和运营管理阶段对道面区(道基、基础、面层)、土面区、巡场道路和服务车道等区域的现场调查、工程质量检测以及技术状况评定。

In-situ measurement specification for pavement and subgrade of civil airports

DB44/T 1162-2013 家用和类似用途空气源热泵热水器安装规范

本标准规定了符合标准GB/T 23137的家用和类似用途空气源热泵热水器（以下简称热泵热水器）产品出厂后，为用户安装时所涉及的人身和财产安全、周围环境、实现产品预定功能以及安装要求、安装操作、检查和试运行、检验方法、安装人员资格确认等。 本标准适用于以空气为热源的家用和类似用途热泵热水器的安装和服务。 本标准不适用于商业或工业用及类似用途的热泵热水器和使用C02为制冷剂的热泵热水器产品。 家用和类似用途空气源热泵热水器使用后的再次安装（如移地安装、维护性拆装等）可参照本标准执行。

Specifications for installation of air source heat pump water heaters for household and similar purposes

DB35/T 1047-2010 即热式电热水器

本标准规定了即热式电热水器的技术要求、试验方法、检验规则和标志、使用说明、包装、运输、贮存。 本标准适用于单相交流额定电压不超过250V和三相交流额定电压不超过450V、进水水压在0. 05MPa以上、进水水温不高于50℃、用电热元件把水加热至95℃以下的家用和类似用途的即热式电热水器(以下简称“热水器”)。

instant electric water heater

SB/T 10460-2008 商用电开水器

本标准规定了商用开水器的术语和定义、产品分类、技术要求、试验方法、检验规则、标志、包装、运输与贮存。 本标准适用于非专供家庭使用的商用电开水器（以下简称开水器）。对于连接一条相线和中性线的单相器具，其额定电压不超过250V，其他器具不超过480V。 利用其他能源形式的器具，如适用，其性能要求也在本标准范围之内。 本标准所涉及的开水器，其安全性能应符合GB 4706.1《家用和类似用途电器的安全 第一部分:通用要求》、GB 4706.36《家用和类似用途电器的安全商用电开水器和液体加热器的特殊要求》。 本标准不适用于： ——专为工业用途而设计的开水器； ——具有电极加热器的开水器； ——在有腐蚀性或爆炸性气体（尘埃、蒸汽或可燃气）等特殊条件使用的电开水器。

Commercial water electric boilers

JG 232-2008 卫浴型散热器

本标准规定了卫浴型散热器的术语与定义、分类与标记、要求、试验方法、检验规则、标志与预留、包装、运输、贮存、保修与更换等。 本标准适用于民用建筑中以热水为热媒、工作热媒温度不高于95 ℃，酸碱度pH=7.0～12.0，氯根、硫酸根含量分别不大于100mg/L，溶解氧不大于0.1mg/L，根据采暖系统的供水情况其他水质指标，分别符合GB 1576和HG/T 3729标准中关于供暖水质要求的卫浴型散热器（以下简称散热器）。

Bath room radiator

JIS C 9202 AMD 1:2008 电辐射加热器(修改件1)

JIS C 9202:1990を，次のように改正する。

Electric radiant heaters (Amendment 1)

KS C 9205-2007(2012) 电烤箱

Electric radiant heaters

JG 2-2007 钢制板型散热器

本标准规定了薄钢板加工成型的钢制板型散热器（以下简称散热器）术语和定义、型号与标记、要求、试验方法、检验规则、标志、包装、运输与贮存。 本标准适用于工业、民用建筑中以热水为热媒的散热器。其热媒温度不高于 120 ℃，热水 pH 值应在 10～12 、氯离子含量不应大于 300mg/L 、溶解氧不应大于 0.lmg/L，其他水质指标应符合 GB 1576 的规定。

Steel panel radiator