97.150 铺地非织物 标准查询与下载

ASTM F1331-22 电气和电子空间中便携式板上乙烯基甲板覆盖物安装程序的标准实施规程

1.1 This practice covers the acceptable method for installing insulated deck covering on portable deck plates. 1.2 This deck covering shall be installed, in way of the electrical and electronic spaces, for marine use. 1.3 The values stated in SI (metric) units are to be regarded as the standard. The values in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Installation Procedures of Vinyl Deck Coverings on Portable Plates in Electrical and Electronic Spaces

ASTM D7330-22 使用标准参考比例尺评估桩地板覆盖物表面外观变化的标准试验方法

1.1 This test method covers the assessment of changes of surface appearance of pile floor coverings after exposure to actual or simulated foot traffic. This test method applies to pile yarn floor coverings that are, or have been, installed; laboratory floor-trafficked samples; or textiles floor coverings trafficked by mechanical traffic simulators. The subjective assessment is facilitated by use of reference scales that are based on digital images of representative pile yarn floor covering styles and constructions. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Assessment of Surface Appearance Change in Pile Floor Coverings Using Standard Reference Scales

ASTM F373-13(2022) 弹性地板覆盖物压花深度的标准试验方法

1.1 Two important characteristics involved in the manufacture of resilient flooring relate to the smoothness of the wear surface and the hardness of the layers under the wear surface. The surfaces may vary from completely textured areas to portions that are flat but separated by textured areas. This test method covers flooring with these interrupted wear surfaces which are not supported by soft, cushioned layers. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Embossed Depth of Resilient Floor Coverings

ASTM F386-17(2022) 平面弹性地板材料厚度的标准试验方法

1.1 This test method covers the determination of thickness of resilient nontextile floor coverings including tile and sheet having flat surfaces. This test method should not be used on materials having a foamed layer. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Thickness of Resilient Flooring Materials Having Flat Surfaces

ASTM F387-17(2022) 测量有泡沫层的弹性地板覆盖物厚度的标准试验方法

1.1 This test method covers the determination of the thickness of resilient non-textile floor coverings containing a foam layer as part of the construction. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measuring Thickness of Resilient Floor Covering With Foam Layer

ASTM D5793-18(2022) 绒线地板覆盖物单位长度或宽度的粘合位置的标准试验方法

1.1 This test method describes the measurement of the number of binding sites per unit length or width of machinemade, woven, knitted, and tufted pile yarn floor covering both before and after adhesive backing application. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Binding Sites per Unit Length or Width of Pile Yarn Floor Coverings

ISO 4760:2022 强化木地板.表面防潮.组装接头

This document specifies a test method to evaluate moisture resistance to surface water exposure of a joined, floating, laminate flooring assembly/element. This document also establishes criteria for rating and assessing performance.

Laminate flooring — Topical moisture resistance — Assembled joint

GSO ASTM D3676:2022 用于地毯或地毯垫层的橡胶蜂窝垫的标准规范

This specification covers material and dimensional requirements for high-density rubber cellular cushion adhered to carpet, rugs, or various substrates intended for use as a separate underlay. However, this specification does not include requirements for burning characteristics. Material covered in this specification comprises Class A and Class B flexible, cellular, high-density rubber. Tests for compression set, compression resistance or compression force deflection, delaminations strength, tensile strength, and accelerated aging shall be performed and shall conform to the requirements specified.

Standard Specification for Rubber Cellular Cushion Used for Carpet or Rug Underlay

BS ISO 24338:2022 层压地板覆盖物 耐磨性的测定

1   Scope This document specifies two methods (A and B) for measuring abrasion of laminate floor covering elements. The tests described measure the ability of the surface layer to resist abrasive wear-through. Abrasion according to method A is achieved by rotating a test specimen in contact with a pair of loaded cylindrical wheels covered with specified abrasive paper. The resistance to wear according to method B is evaluated by abrading the face of test pieces with a specified abrasive applied by means of two loaded wheels. The number of revolutions of the test specimen required to cause a defined degree of abrasion is measured by both methods. NOTE The precision of the methods is not known. When inter-laboratory data become available, a precision statement will be added.

Laminate floor coverings. Determination of abrasion resistance

ISO 24338:2022 层压地板覆盖物.耐磨性的测定

This document specifies two methods (A and B) for measuring abrasion of laminate floor covering elements. The tests described measure the ability of the surface layer to resist abrasive wear-through. Abrasion according to method A is achieved by rotating a test specimen in contact with a pair of loaded cylindrical wheels covered with specified abrasive paper. The resistance to wear according to method B is evaluated by abrading the face of test pieces with a specified abrasive applied by means of two loaded wheels. The number of revolutions of the test specimen required to cause a defined degree of abrasion is measured by both methods. NOTE The precision of the methods is not known. When inter-laboratory data become available, a precision statement will be added.

Laminate floor coverings — Determination of abrasion resistance

ASTM D7983-17(2022) 地毯背衬织物收缩率的标准试验方法

1.1 This test method covers the procedure for evaluating shrinkage, in both wet and dry conditions, of woven, knitted and nonwoven backing fabrics designed for use in the manufacture of pile yarn floor coverings. Determination of carpet backing shrinkage was previously contained within Test Methods D2646. For consistency, Subcommittee D13.21 extracted this portion and created a separate test method. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Shrinkage of Carpet Backing Fabrics

ASTM D6540-22 绒线地板覆盖物加速弄脏的标准试验方法

1.1 This test method describes the equipment, and the test method for assessing the propensity of pile yarn floor coverings to soiling in the absence of abrasive wear and texture changes, using a standard synthetic soil composition. 1.2 This test method is applicable for use in testing unused pile yarn floor covering of all types. It is not applicable for use in testing used pile yarn floor covering. 1.3 This test method can be used to compare the soiling propensity of two or more carpets; or it can be used to soil carpets as a preliminary step to other test procedures. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Accelerated Soiling of Pile Yarn Floor Covering

ASTM D6719-22e1 评估绒线地板覆盖物的标准试验方法和实践指南

1.1 This guide provides users with an index of procedures in the form of test methods, practices, and related documents that are currently used in industry for determination of properties of pile yarn floor covering. This guide is not considered as all-inclusive for testing procedures related to pile yarn floor covering. 1.1.1 It is the responsibility of the user to choose from this guide those procedures that provide test information on properties of interest for pile yarn floor covering that relate to its physical and esthetic properties and performance. 1.1.2 Procedures for properties appear in the following sections: Property Section Surface Appearance Change 8.1, 8.2, 8.3, 8.4, 8.31, and 8.35 Antimicrobial 8.5 Binding Sites 8.6 Backing Characteristics 8.7 Colorfastness to Light, Crocking, Ozone, Water, and Oxides of Nitrogen 8.8 – 8.12 Carpets, Cleaning 8.13 and 8.14 Conditioning 7 Delamination Resistance 8.15 Fiber Analysis 8.16 Flammability 8.17 – 8.20 Pile Thickness 8.21 Mass per Unit Area 8.22 Soiling 8.23 – 8.25 Stain Resistance 8.26 Static 8.27 Tuft Bind 8.28 Tuft Height 8.29 Tuft Element Length 8.30 Durability 8.32 Edge Ravel 8.33 Dimensional Stability 8.34 Fluorine Content 8.36 Colorfastness to Sodium 8.37 Installation of Commercial Carpet 8.38 Installation of Residential Carpet 8.39 Maintenance and Cleaning of Commercial Carpet 8.40 Maintenance and Cleaning of Residential Carpet 8.41 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are nonrationalized mathematical conversions to SI units that are provided for information only and are not considered standard. 1.2.1 Some of the listed procedures may cite other units as standard. In this event, language of the procedure is controlling. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Standard Test Methods and Practices for Evaluating Pile Yarn Floor Covering

22/30445553 DC BS EN 14499 纺织地板覆盖物 地毯衬垫的分类

BS EN 14499. Textile floor coverings. Classification of carpet underlays

KS K ISO 25620:2021 层压地板覆盖物.机械组装面板长边摩擦的测定

Laminate floor coverings — Determination of long-side friction for mechanically assembled panels

KS K ISO 12951-2021 铺地织物.用Lisson-Tretrad机器测定质量损失、纤维粘合和楼梯前缘外观变化

Textile floor coverings — Determination of mass loss, fibre bind and stair nosing appearance change using the Lisson Tretrad machine

KS K ISO 10874-2021 弹性织物和层压地板覆盖物.分类

Resilient, textile and laminate floor coverings — Classification

KS K ISO 12951:2021 铺地织物.用Lisson-Tretrad机器测定质量损失、纤维粘合和楼梯前缘外观变化

Textile floor coverings — Determination of mass loss, fibre bind and stair nosing appearance change using the Lisson Tretrad machine

KS K ISO 11858-2021 铺地织物.附着泡沫易碎性的测定

Textile floor coverings — Determination of friability of attached foams

KS K ISO 10874:2021 弹性织物和层压地板覆盖物.分类

Resilient, textile and laminate floor coverings — Classification