97.160 家用织物、亚麻织物 标准查询与下载

FZ/T 62013-2019 再生纤维素纤维凉席

regenerated cellulose fiber mat

T/TZJF 005-2019 乳胶凉感床上用品

本标准规定了乳胶凉感床上用品的术语和定义、技术要求、试验方法、检验规则、包装、贮运和标志。 本标准适用于以乳胶为填充物制作而成的具有接触凉感的乳胶凉感床上用品。包括凉感乳胶凉席、凉感乳胶枕及其组合而成的成套床上用品。

Latex cool bedding

T/TZJF 006-2019 针织面料床上用品

本标准规定了针织面料床上用品的技术要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于以各类针织面料为主要原料制成的床上用品，包括机织面料与针织面料拼接的床上用品（机织面料不超过产品总面积的30%）。

Knitwear bedding

T/HOMETEX 6-2019 成品窗帘

3　规格 成品窗帘的规格由以厘米为单位的窗帘单幅宽度和高度表示：高度应与建筑物层高匹配，以不低于250 cm为宜；宽度为窗帘自然展开后的覆盖宽度，按合同或协议设计。单幅宽度以135 cm为基准，每15 cm递增，推荐系列如下：135、150、165、180、195、210。 4　技术要求 4.1　成品窗帘内在质量要求见表1。 表 1 内在质量 序号　项  目　要  求 1　纤维含量允差/ %　符合GB/T 29862要求 2　甲醛含量/（mg/kg）                              ≤　300 3　pH值　4.0～9.0 4　可分解致癌芳香胺染料/（mg/kg）                  ≤　20 5　异味　无 6　断裂强力（机织类）/N                            ≥　250（窗纱180） 7　撕破强力（机织类）/N                            ≥　10 8　胀破强度（针织类）/kPa                          ≥　200 9　水洗尺寸变化率a)/%               　-3～+3 10　干洗尺寸变化率b)/% 　-3～+3 11　染色牢度c)/级         ≥　耐水（变色、沾色）　3-4 　　耐摩擦（干摩）　3-4 　　耐摩擦（湿摩）　3 　　耐皂洗（变色、沾色）　3-4 　　耐干洗（变色、沾色）　3-4 　　耐光　4 12　燃烧性能d)          ≤　损毁长度/mm　150 　　续燃时间/s　5 　　阴燃时间/s　5 a   水洗尺寸变化率、耐皂洗色牢度考核可水洗产品； b   干洗尺寸变化率、耐干洗色牢度考核可干洗的产品； c   除耐光外,本白和漂白产品不考核色牢度； d   明示阻燃产品的考核燃烧性能。 4.2　成品窗帘的外观质量要求见表2。 表2 外观质量 序号　项  目　要  求 1　规格尺寸偏差　宽度　－1 cm 　　高度　－3 cm～+3 cm 2　色差        　同窗　不低于4-5级 　　同批　不低于3-4级  3　布面疵点　破损　不允许 　　针眼　不明显，长度小于20 cm。 　　色、污渍　4级沾污，允许1处/件 　　线状疵点　轻微允许2处/件 　　条块状疵点　轻微允许2处/件 　　印花不良　不影响整体外观 4　缝纫质量　侧边包边　不小于2 cm，宽度均匀 　　褶间距　各褶间距离均匀 　　卷边拼缝　平服齐直，宽狭一致，不露毛 　　针迹密度　平缝不小于9针/3 cm，包缝不小于9针/3 cm 　　缝迹　轨迹匀、直、牢固，无跳针、浮针、漏针和脱线，偏针不超过0.5 cm/20 cm，接针套正，边口处必须打回针 6　窗帘勾带质量　穿扣顺畅，能维持成品窗帘悬挂 7　窗帘勾子质量　表面光滑、穿扣顺畅、不易生锈 注：外观疵点及程度说明参见附录A。

Curtains

T/HOMETEX 11-2019 纺织浴帘

5.1 基本安全要求 基本安全要求符合GB18401。 5,2 产品内在质量 产品的内在质量要求见表2。   5.3 产品的外观质量 产品的外观质量要求见表3。

Textile shower curtain

T/HOMETEX 10-2019 家居布拖鞋

4.1　鞋号和型号 布拖鞋的鞋号按脚的长度和对应尺码标注，参照按照GB/T3293.1 执行，型号由制造者自行设计。 4.2　帮面、衬里和内底用织物 帮面、衬里和内底用织物应符合表1的要求，婴幼儿拖鞋不采用涂层或涂料印花织物。 4.3　外底 外底应符合表2的要求。 4.4　成品质量 拖鞋的成品应符合表3的要求。

Fabric house slippers

T/HOMETEX 8-2019 旅游饭店用精品纺织品

5.1  产品的内在质量要求 5.1.1  客房床上用品内在质量应符合表1的要求。 5.1.2 卫浴巾类产品内在质量应符合表2的要求。 5.2 产品的外观质量要求。 5.2.1  客房床上用品外观质量应符合表3的要求。 5.2.2  卫浴巾类产品外观质量应符合表4的要求。 5.3  产品应符合GB18401要求，婴童产品应符合GB31701规定的要求。 5.4 选用合适缝线、纽扣、拉链等附件，且质量符合相关标准要求。 5.5 产品上不允许残留对人体有伤害的金属针等锐利物。 5.6  特殊要求按双方合同协议的规定执行。

High-quality textiles for tourist hotels

T/HOMETEX 7-2019 绣花床上用品

3.1  产品质量等级分为优等品、一等品、合格品。                           3.2  产品主要规格按FZ/T60032选择。 3.3  产品质量包括绣花质量、缝制质量、外观质量和内在质量。 3.4  绣花质量要求见表1。 3.5  缝制质量要求见表2。 3.6   外观质量要求见表3。 3.7  内在质量按要求见表4。 3.8  选用适合的缝线、绣花线、纽扣、拉链等附件，质量应符合相关标准要求。 3.9   产品上不允许残留金属针等锐利物。 3.10  产品应符合GB18401要求，婴童产品应符合GB31701规定的要求。

Embroidered bedding

T/HOMETEX 9-2019 一次性纯棉洗脸巾

3.1　卫生要求应符合GB 15979《一次性使用卫生用品卫生标准》规定，其中微生物学指标应符合产品种类“纸巾”的规定要求。 3.2　产品的基本安全技术要求应符合GB 18401规定，婴幼儿及儿童产品应符合GB 31701规定要求。 3.3  产品内在质量要求见表1。 3.4 产品外观质量要求见表2。

Disposable cotton facial towel

T/XFBZ 011-2019 学生床上用品

本标准规定了中小学生床上用品的术语和定义、要求、检验方法、 抽样、检验规则、产品使用说明、包装、运输和贮存。 本标准适用于以纺织机织物为主要面料生产的中小学生床上用品。 其他学生床上用品可以参照执行。

student bedding

T/ZZB 1332-2019 慢回弹枕、垫类产品

本标准规定了慢回弹枕、垫类产品的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、使用说明、包装和质量承诺。 本标准适用于以慢回弹软质聚氨酯泡沫塑料为主要原料制作枕芯或垫芯，以针织面料制作外套的、不使用絮状纤维的床上用枕、垫类产品。 本标准不适用于（0～36）个月的儿童用枕、垫类产品，不适用于床垫。

Memory pillow and cushion

T/ZZB 1344-2019 全棉生态床品套件

本标准规定了全棉生态床品套件的基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺等。 本标准适用于全棉生态机织面料制成的床品套件。

Ecological cotton bedding set

T/ZZB 1278-2019 防钻绒羽绒被

本标准规定了防钻绒羽绒被的基本要求、技术要求、试验方法、检验规则、包装、标志、运输及贮存和质量承诺。 本标准适用于以标称绒子含量90%及以上的羽绒为主要填充物，以全棉或棉与桑蚕丝混纺或交织的防钻绒面料为被壳并采用密封缝制工艺的羽绒被.

Down-proof quilt

T/ZZB 1146-2019 防螨抗菌被子

本标准规定了防螨抗菌被子的基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。本标准适用于具有防螨抗菌性能的被子。 本标准不适用于婴幼儿及儿童（14岁及以下）用产品。

Anti-mite and antibacterial quilt

DB35/T 1825-2019 皮革材质鉴别试验方法

本标准规定了牛、羊、猪、马等皮革及制品鉴别试验方法的原理、仪器设备和化学试剂、试样的准备、试验步骤、结果表示和试验报告。 本标准适用于牛、羊、猪、马等皮革及制品的鉴别。 本标准不适用于再生皮革的鉴别。

Leather material identification test method

ASTM D4111-12(2019) 织布和桌布织物的标准性能规范:家庭和机构

1.1 This performance specification covers woven fabrics comprised of any textile fiber or mixture of fibers to be used in napery and tablecloths (household and institutional). 1.2 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Performance Specification for Woven Napery and Tablecloth Fabrics: Household and Institutional

ASTM D4113-02(2019) 机织套袖织物的标准性能规范

1.1 This performance specification covers woven fabrics comprised of any textile fiber or mixture of fibers to be used in slipcovers. 1.2 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Performance Specification for Woven Slipcover Fabrics

ASTM D5433-12(2019) 公共和家用毛巾产品的标准性能规范

1.1 This specification covers the evaluation of specific performance characteristics of importance in woven and knitted kitchen towel, dishcloth, crash towel, huck towel, washcloth, hand towel, bath towel, and bath sheet products for use in institutional and household environments. 1.2 This specification may be used by mutual agreement between the purchaser and the supplier to establish purchasing specification requirements. 1.3 The requirements in Tables 1 and 2 apply to the length and width directions for those properties where fabric direction is pertinent. 1.4 This specification is not applicable for coated and laminated products, nonwoven products, or terry fabrics used for apparel. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Performance Specification for Towel Products for Institutional and Household Use

ASTM D5431-08(2019) 机构和家用机织和针织薄板产品的标准性能规范

1.1 This specification covers the evaluation of specific performance characteristics of importance in woven and knit flat, fitted, and waterbed sheet products for use in institutional and household environments. 1.2 This specification may be used by mutual agreement between the purchaser and the supplier to establish purchasing specification requirements. 1.3 The requirements in Table 1 apply to the length and width directions for those properties where fabric direction is pertinent. 1.4 This specification is not applicable to woven and knit products used for sheet blankets or to woven and knitted sheet products used for apparel. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Performance Specification for Woven and Knitted Sheeting Products for Institutional and Household Use

ASTM D6663-08(2019) 机构和家用机织和针织棉被及附属产品的标准规范

1.1 This specification covers the evaluation of specific performance characteristics of importance in woven and knit comforter and accessory products, except for pillows and window treatments, for use in institutional and household environments. 1.2 The following safety hazards caveat pertains only to the test methods described in this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Woven and Knitted Comforter and Accessory Products for Institutional and Household Use