A20 综合技术 标准查询与下载

JIS Z 8402-6 ERRATUM 1:2007 勘误表

ERRATUM

SJ/T 11080-2007 阴极射线管参考线量规尺寸

本标准规定了阴极射线管参考线量规（以下简称参考线量规）的代号、名称和尺寸。 本标准适用于确定阴极射线管及其玻壳的参考线位置。

Dimensions of reference line gauge for cathode-ray tubes

KS A 3112-2007 故障信息报告、分析及纠正措施系统

이 규격은 체계나 설비의 설계, 개발, 제조, 시험 및 시스템의 운영, 그리고 장비와 연계

Failure Reporting, Analysis and Corrective Action System(FRACAS)

ISO 7870-1:2007 控制图表.第1部分:一般指南

This part of ISO 7870 presents key elements and philosophy of the control chart approach, and identifies a wide variety of control charts (including those related to the Shewhart control chart and those stressing process acceptance or on-line process adjustment). It presents an overview of the basic principles and concepts and illustrates the relationship among various control chart approaches to aid in the selection of the most appropriate standard for given circumstances. It does not specify statistical control methods using control charts. These methods will be specified in future parts of ISO 7870.

Control charts - Part 1: General guidelines

SB/T 10437-2007 美容美发行业经营管理技术规范

本标准规定了美容美发行业的定义、专业条件和经营管理应具备的专业要求。 本标准适用于美容院、美发厅、美体中心、美甲店、综合性美容美发中心等经营机构。

Management and technical standards for beauty enterprises

JIS Z 8402-5 ERRATUM 1:2007 勘误表

ERRATUM

DB65/T 2782-2007 喀纳斯景区旅游纪念品质量要求

Standard quality of tourist souvenir of Kanasi

DIN-Fachbericht 150:2007 破坏性测试的检验人员资格鉴定

Qualification of personnel for destructive testing

JIS C 9911:2007 回收的计算和显示方法及电气或电子设备的再利用指标

この規格は，電気?電子機器(以下，“機器”という。)の設計?製造段階における資源の有効利用の取組みの成果を評価するため，機器及び部品の設計?製造段階において，資源が再利用される割合を設計段階で示す指標の算定及び表示方法について規定する。

Calculation and display methods of recycled and reuse indicator of electric or electronic equipment

ASTM E1804-07 项目设计阶段的执行和报告成本分析用标准实施规程

This practice increases the level of communication, provides an organized approach to cost control during the design of a project, and also provides a means of identifying extraordinary cost items and changes in assumptions between estimates. The users of this practice include owners, developers, contractors, cost professionals, estimators, architects, engineers, specification writers, quantity surveyors, and anyone charged with the responsibility of successfully managing the design of a building within a specified budget. Use this reporting format during the following: 5.3.1 Contracting for design cost analysis services, 5.3.2 Comparing the current design costs to a previous estimate, and 5.3.3 Responding to each design phase. This practice provides a tool for analyzing design options and examining strategies to maintain the building budget.1.1 This practice covers an arranged method for providing cost analysis during the design phase of buildings.1.2 The use of this practice increases the level of communication between the design professional, owner, and the cost professional providing the cost consulting services.1.3 The practice establishes a structured method to support design decisions.1.4 The practice provides design and cost professionals with a framework for historically tabulating information to be used on relevant future projects.

Standard Practice for Performing and Reporting Cost Analysis During the Design Phase of a Project

ASTM E2480-07 对带多值被测对象试验方法的精度测定进行的多实验室间研究用标准实施规程

ASTM regulations require precision statements for all test methods in terms of repeatability and reproducibility. This practice may be used in obtaining the information needed to prepare a precision statement in accordance with Practice E 177 and the “Blue Book.”1.1 This practice describes the techniques for planning, conducting, and analyzing the results of an interlaboratory study (ILS) conducted for certain test methods within Committee E12.1.2 This practice does not concern itself with the development of the test method but rather with the gathering of the information needed for the precision and bias statement after the completion of development of the test method. The data obtained in the ILS may indicate, however, that further effort is needed to improve the test method.1.3 This practice is concerned exclusively with test methods that derive a multi-valued measurand, such as, but not limited to, spectral reflectance, transmittance function, tristimulus values, or RGB values. Variation in measurements of such multi-valued measurands are usually analyzed by reducing the data to a single-valued parameter, such as color difference, E.1.4 This practice covers methods of dealing with the non-normal distribution of the variation of sets of color-differences. This is done so that the user may derive valid statistics from such non-normal distributions.1.5 This practice does not cover test methods, even in Committee E12, whose measurands are single-valued, or whose variations are known to be normally distributed. Task groups involved with such test methods are referred to Practice E 691 which contains preferable methods of analyzing data with those properties.1.6 This practice is not intended to establish a method for estimating possible color-difference tolerances.1.7 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method with Multi-Valued Measurands

CGA M-6-2007 分析方法确认用指南.第1版

This publication describes the minimum requirements for validating noncompendial analytical test methods. It also describes a method for establishing the equivalency of alternate test methods. This publication is intended to meet the requirements of: - Title 21 of the U.S.Code of Federal Regulations(21CFR) Part 211.165(e), 211.194(a)(2), and 820.72(a)(2); and - Chapter 1225(Validation of Compendial Methods) and portions of Chapter 621(Gas Chromatography) in the USP-NF[1].

GUIDELINE FOR ANALYTICAL METHOD VALIDATION FIRST EDITION

DIN 32937:2006 检验、测量和试验设备的控制.检验、测量和试验设备的计划、管理和使用

This standard specifies requirements for the surveillance of measuring, testing and inspection equipment and describes the implementation of a surveillance system for the planning, management and use of such equipment. By meeting the requirements of the present standard users will also meet the relevant requirements for the surveillance of measuring, testing and inspection equipment required by management systems, e.g. as specified in DIN EN ISO 9001.

Control of inspection, measuring and test equipment - Plan, manage and use of inspection, measuring and test equipments

NAVY DI-SESS-81525 B VALID NOTICE 1-2006 测试包

DI-SESS-81525B, dated 30 August 2001, has been reviewed and determined to be valid for use in acquisition.

TEST PACKAGE

AIR FORCE A-A-50718 A-2006 燃油系统测试装置

This Commercial Item Description, (CID), describes an AC Fuel Quantity Test Set based on Bridge Capacitance/Resistance Test Set (BC/RFGTS) technology herein referred to as test set. This CID describes a minimum requirement for the test set in which only

TEST SET, FUEL SYSTEM

ASTM G190-06 制定和选择磨损试验的标准指南

The guidance and methodology provided by this guide is applicable for any wear situation and is not limited to material or lubrication. This guide is intended to provide general information and guidance regarding the selection and development of a wear test and does not provide specifics about any one wear test or intended application. In general the variability and correlation that is obtained with any wear test is determined by the degree to which the various elements of the wear test methodology described in this guide are followed.1.1 This guide covers general information for the development and selection of a wear test for an intended application.

Standard Guide for Developing and Selecting Wear Tests

AIR FORCE A-A-59480-2004 便携式液压压力表测试仪(数字或重负)

This CID describes a pressure gage tester and calibrator. The pressure gage tester is for testing direct pressure gages, relief valves, servos, pressure operated devices such as pressure switches, and static testing pressure lines.

TESTER, PRESSURE GAGE, HYDRAULIC, PORTABLE (DIGITAL OR DEADWEIGHT)

AIR FORCE A-A-59604-2004 射频功率测试装置(50MHZ至40GHZ)

This commercial item description describes the minimum requirements for a Radio Frequency Power Test Set, which consists of a dual channel radiofrequency (RF) power meter,sensors, and applicable accessories. The equipment, as described in this CID,has a

TEST SET, RADIO FREQUENCY POWER (50 MHZ TO 40 GHZ)

AIR FORCE A-A-59577-2004 美国材料试验协会D93闪点测试仪 方法A及方法B

This Commercial Item Description (CID), describes Tester, Flash Point Closed Cup,ASTM D93 Method A and B. The flash point tester is used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under contr

TESTER, FLASH POINT ASTM D93 METHOD A AND B

AIR FORCE A-A-59579-2004 AC/DC质量燃料控制系统测试装置

The equipment shall be capable of operation and be bid sample tested within the accuracies, limits, and specifications herein. Equipment covered by this CID shall be commercially available equipment and may be modified to the extent necessary to meet th

TEST SET, FUEL CONTROL SYSTEM - AC/DC QUANTITY