D53 建材原料矿 标准查询与下载

QB/T 1635-1992 日用陶瓷用高岭土

本标准规定了日用陶瓷用高岭土的产品分类、技术要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于由高岭石、多水高岭石等为主要矿物组成，用来制造日用陶瓷的高岭土产品。

Kaolin for daily ceramics

QB/T 1636-1992 日用陶瓷用长石

本标准规定了日用陶瓷用长石的产品分类、技术要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于日用陶瓷用长石产品。

Feldspar for daily ceramics

QB/T 1641-1992 陶瓷用石膏化学分析方法

本标准规定了石膏吸附水、结晶水、酸不溶物、三氧化硫、氧化钙、氧化镁、二氧化硅、三氧化二铝、三氧化二铁、二氧化钛、氧化钾、氧化钠成分的分析方法。 本标准适用于含二水硫酸钙为主要成分的天然石膏和含半水硫酸钙为主要成分的陶瓷模用石膏粉的定量化学分析。

Chemical analysis method of gypsum for ceramics

QB/T 1640-1992 陶瓷模用石膏粉物理性能测试方法

本标准规定了陶瓷模用石膏份的筛余量、标准稠度、凝结时间、抗折强度、抗压强度的测试条件及测试方法。 本标准适用于陶瓷注模用半水石膏粉。

Test methods for physical properties of gypsum powder for ceramic molds

QB/T 1637-1992 日用陶瓷用石英

本标准规定了日用陶瓷用石英的产品分类、技术要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于日用陶瓷用石英产品。

Quartz for daily ceramics

ASTM D3639-92(2002) 用魁北克试验对石棉分类的试验方法

1.1 This test method covers a procedure for dry classification of chrysotile asbestos fiber by length distribution. 1.2 The values stated in inch-pound units are to be regarded as the standard. The equivalent SI units may be approximate. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the respoinsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 7.2 for a specific warning statement.

Standard Test Method for Classification of Asbestos by Quebec Standard Test

ASTM D3639-92(2002)e2 用魁北克试验对石棉分类的试验方法

1.1 This test method covers a procedure for dry classification of chrysotile asbestos fiber by length distribution.1.2 The values stated in inch-pound units are to be regarded as the standard. The equivalent SI units may be approximate.1.3 Warning- Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysoltile asbestos, refer to "Safe Use of Chrysotile Asbestos: A Manual on Preventive and Control Measures."This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See for a specific hazard warning.

Standard Test Method for Classification of Asbestos by Quebec Standard Test

ASTM D3639-92(2006) 用魁北克试验对石棉分类的试验方法

The Quebec Standard Testing Machine classifies milled chrysotile asbestos grades according to the mass fractions retained on each screen. Specimens that are not properly conditioned prior to testing or that have excessive moisture content (above 3 % in accordance with Method D 2987), or both, may give erratic and false results. Some amphibole asbestos fibers may be classified by this test method but a standard classification for these has not been established. 1.1 This test method covers a procedure for dry classification of chrysotile asbestos fiber by length distribution.1.2 The values stated in inch-pound units are to be regarded as the standard. The equivalent SI units may be approximate.1.3 Warning - Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysoltile asbestos, refer to "Safe Use of Chrysotile Asbestos: A Manual on Preventive and Control Measures."This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See for a specific hazard warning.

Standard Test Method for Classification of Asbestos by Quebec Standard Test

ASTM D3639-92(2006)e1 用魁北克试验对石棉分类的标准试验方法

The Quebec Standard Testing Machine classifies milled chrysotile asbestos grades according to the mass fractions retained on each screen. Specimens that are not properly conditioned prior to testing or that have excessive moisture content (above 3 % in accordance with Method D 2987), or both, may give erratic and false results. Some amphibole asbestos fibers may be classified by this test method but a standard classification for these has not been established. 1.1 This test method covers a procedure for dry classification of chrysotile asbestos fiber by length distribution. 1.2 The values stated in inch-pound units are to be regarded as the standard. The equivalent SI units may be approximate. 1.3 Warning8212;Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysoltile asbestos, refer to “Safe Use of Chrysotile Asbestos: A Manual on Preventive and Control Measures.” 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 1.3 for a specific hazard warning.

Standard Test Method for Classification of Asbestos by Quebec Standard Test

JIS M 8855:1991 蜡石的化学分析方法

Methods for chemical analysis of roseki

JIS M 8016:1991 纸张填料和涂层的试验方法

この規格は，製紙用(てん料・塗工用)に使用されるろう石クレー(以下，クレーという。)の試験方法について規定する。

Testing methods of filler and coating clay for paper

NF B10-513:1991 采石场产品.天然石.抗冻裂试验

Quarry products. Natural stones. Frost resistance test.

YB/T 4032-1991 蓝晶石 硅线石 红柱石

kyanite sillimanite andalusite

ASTM D3879-91(2004)e1 角闪石石棉取样的标准试验方法

Sampling and conditioning are equally as important as testing. The reliability of the test results depends primarily upon how well the specimens tested represent the true character and condition of the lot of asbestos fiber. Much care and effort are required to be sure that all the sampling operations are systematic or at random, and are representative. Failure to provide a test specimen that accurately represents the lot from which it is drawn will produce misleading test results regardless of the accuracy and the precision of the test method.1.1 This test method describes the procedure for taking a composite sample or a master composite sample (at the mine, at the factory, or from a consignment) from a lot of commercial milled amphibole fibers, conditioning the sample, and reducing it in quantity so as to provide a series of relatively small test specimens of loose asbestos fiber, each of which may be regarded as representative of the lot. (See for sampling strategy.) 1.2 This test method is suitable for taking test specimens of amphibole asbestos for the following test methods: C 1119, C 1120, C 1121, C 1122, C 1123, C 1124, C 1125, C 1162, D 1118, D 2589, D 2752, D 2947, D 2985, D 2987, D 3639, D 3752, and D 3880.1.3 For sampling chrysotile asbestos, use Method D 2590.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.5 Warning-Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysoltile asbestos, refer to "Safe Use of Chrysotile Asbestos: A Manual on Preventive and Control Measures."This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See for a specific hazard warning.

Standard Test Method for Sampling Amphibole Asbestos

STAS 11828/4-1990 农用机械．播种单元．主要参数

Prezentul standard stabile?te parametrii principali ai agregatelor pentru sem?nat, care concomitent cu sem?natul efectueaz? ?i alte lucr?ri;: m?run?irea ?i af?narea solului distribuirea de ?ngr???minte chimice, insecticide, erbicide ?i fungicide etc.

Agricultural machines. Sowing units. Main parameters

ASTM D2589-88(2006) 石棉纤维的麦克涅特湿法分类的标准试验方法

Normally, results obtained by this test method are reproducible under comparable laboratory conditions. However, it must not be expected that results obtained by different operators at various laboratories and times will be in exact agreement due to some seemingly minor procedural change. Moreover, results for longer fiber grades are influenced to a greater extent by differences in fiber length distribution and characteristics than those of shorter grades.1.1 This test method covers the determination of the length distribution and fines content of milled asbestos fiber by wet classification employing the McNett fiber classifier.1.2 The values stated in SI units are the standard. The inch-pound units shown in parentheses are provided for information only.1.3 Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysotile asbestos, refer to "Safe Use of Chrysotile: A Manual on Preventive and Control Measures."This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for McNett Wet Classification of Dual Asbestos Fiber

ASTM D2947-88(2002)e1 石棉纤维筛选分析的试验方法

1.1 This test method covers a dry screen analysis for asbestos fiber by means of a mechanical sieve shaker.1.2 This test method is limited in its application to Group 4 and shorter chrysotile asbestos fiber samples as defined in Test Method D 3639. However, some short amphibole asbestos fibers may be suitable for evaluation by this method.1.3 The values stated in SI units are standard. The inch-pound (customary) units in brackets are presented for information only.1.4 Warning-Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysoltile asbestos, refer to "Safe Use of Chrysotile Asbestos: A Manual on Preventive and Control Measures."This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific safety hazard, see .

Standard Test Method for Screen Analysis of Asbestos Fibers

ASTM D2589-88(2006)e1 石棉纤维的麦克涅特湿法分类的标准试验方法

Normally, results obtained by this test method are reproducible under comparable laboratory conditions. However, it must not be expected that results obtained by different operators at various laboratories and times will be in exact agreement due to some seemingly minor procedural change. Moreover, results for longer fiber grades are influenced to a greater extent by differences in fiber length distribution and characteristics than those of shorter grades.1.1 This test method covers the determination of the length distribution and fines content of milled asbestos fiber by wet classification employing the McNett fiber classifier. 1.2 The values stated in SI units are the standard. The inch-pound units shown in parentheses are provided for information only. 1.3 Warning8212;Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysotile asbestos, refer to “Safe Use of Chrysotile: A Manual on Preventive and Control Measures.” 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for McNett Wet Classification of Dual Asbestos Fiber

ASTM D2947-88(2006) 石棉纤维筛选分析的试验方法

Test results give some indication of the apparent fiber length distribution in the sample tested. Sieves are ideally suited to measure particle size and particle size distribution when all three axes of the particle are equidimensional or the particle is of spherical shape. Asbestos fibers differ considerably from these ideal conditions and, therefore, results depart from a true measure of fiber length and length distribution. Characteristics that influence screening efficiency influence test results. Among these are moisture content, degree of fiberization, harshness, and the tendency for fibers to cling together, and of short fibers and fines to cling to longer fibers. In spite of its shortcomings, this test method is particularly useful because of its simplicity and speed and satisfactory reproducibility. The test is suitable for specification acceptance and manufacturing control.1.1 This test method covers a dry screen analysis for asbestos fiber by means of a mechanical sieve shaker.1.2 This test method is limited in its application to Group 4 and shorter chrysotile asbestos fiber samples as defined in Test Method D 3639. However, some short amphibole asbestos fibers may be suitable for evaluation by this method.1.3 The values stated in SI units are standard. The inch-pound (customary) units in brackets are presented for information only.1.4 Warning-Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysoltile asbestos, refer to "Safe Use of Chrysotile Asbestos: A Manual on Preventive and Control Measures."This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific safety hazard, see 1.4.

Standard Test Method for Screen Analysis of Asbestos Fibers

ASTM D2589-88(2002)e2 石棉纤维的麦克涅特湿法分类的标准试验方法

1.1 This test method covers the determination of the length distribution and fines content of milled asbestos fiber by wet classification employing the McNett fiber classifier.1.2 The values stated in SI units are the standard. The inch-pound units shown in parentheses are provided for information only.1.3 Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysotile asbestos, refer to "Safe Use of Chrysotile: A Manual on Preventive and Control Measures."This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for McNett Wet Classification of Dual Asbestos Fiber