共找到 431 条与 合成橡胶 相关的标准,共 29 页
Implants for surgery - Validation requirements for cleaning process of orthopaedic implants before final packaging
Rubber, raw natural. Determination of the gel content of technically specified rubber (TSR)
Rubber. Guide to the calibration of test equipment
Materials for surgical implants - Determination of surface finish of coatings used for biomedical applications
Rubber. Determination of 5-ethylidenenorbornene (ENB) or dicyclopentadiene (DCPD) in ethylenepropylene-diene (EPDM) terpolymers
Implants for surgery - Ceramic materials based on yttria-stabilized tetragonal zirconia (Y-TZP)
Non-active surgical implants - General requirements
Rubber. Identification. Infrared spectrometric methods
3.1 The purpose of this specification is to provide meaningful tests for rubber cellular cushion used for carpet or rug underlay. 1.1 This specification covers high-density cellular rubber adhered to carpet, rugs, or various substrates for use as separate underlay. It is also acceptable to use this standard as a specification for separately blown sponge used as carpet underlay. 1.2 This specification provides material and dimensional requirements and test methods for specific properties of compression set, compression resistance or compression force deflection, delamination strength, and accelerated aging. Note 1—This specification does not include requirements for burning characteristics. It shall be noted that Flammable Fabrics Act Regulations FF1-70, Standard for the Surface Flammability of Carpets and Rugs, and FF2-70, Standard for the Surface Flammability of Small Carpets and Rugs,2 may be applicable for carpets and rugs with integral backing of rubber cellular cushion. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 2—There is no known ISO equivalent to this standard.
Standard Specification for Rubber Cellular Cushion Used for Carpet or Rug Underlay
4.1 The failure of a building sealant in a joint that experiences movement is manifested by cohesive failure in the sealant or adhesive failure between the sealant and substrate, or both. This test method evaluates the performance of one-part elastomeric solvent release sealants in joints subjected to movement and temperature aging. 1.1 This test method is a laboratory procedure that determines the adhesion and cohesion performance of one-part elastomeric, solvent release sealants at high and low temperatures by the extension and compression of test specimens. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The subcommittee with jurisdiction is not aware of any similar ISO standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement, see Note 2.
Standard Test Method for Adhesion and Cohesion of One-Part Elastomeric Solvent Release Sealants
Rubber, vulcanized. Determination of creep in compression or shear
이 표준은 연질 발포 고분자 재료로 된 시험편이 절단될 때까지 일정한 속도로 신장시켰을 때
Flexible cellular polymeric materials-Determination of tensile strength and elongation at break
Rubber. Determination of viscosity and stress relaxation using a rotorless sealed shear rheometer
이 표준은 합성 고무 라텍스의 고속 기계적 안정성을 측정하기 위한 방법을 규정한다. 이 방
Rubber latex, synthetic-Determination of mechanical stability-Part 1:High-speed method
이 표준은 범용 합성 고무 베일을 저장하거나 포장할 때 서로 붙지 않도록 하기 위하여 사용
Film for wrapping rubber bales-Part 3:Ethylene-propylene-diene rubber (EPDM), acrylonitrile-butadiene rubber (NBR), hydrogenated nitrile-butadiene rubber (HNBR), acrylic-ethylene rubber (AEM) and acrylic rubber (ACM)
이 표준은 범용 합성 고무 베일을 저장하거나 포장할 때 서로 붙지 않도록 하기 위하여 사용
Film for wrapping rubber bales-Part 1:Butadiene rubber (BR) and styrene-butadiene rubber (SBR)
이 표준은 천연 고무 베일을 저장할 때 서로 붙지 않도록 하기 위하여 사용되는, 벗겨지지
Film for wrapping rubber bales-Part 2:Natural rubber
이 표준은 합성 고무 라텍스의 기계적 안정성을 측정하기 위한 방법을 규정한다. 이 방법은
Rubber latex, synthetic-Determination of mechanical stability-Part 2:Moderate-speed method under load
Rubber, vulcanized or thermoplastic. Determination of dead-load hardness using the very low rubber hardness (VLRH) scale
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号