G42 胶管、胶带、胶布 标准查询与下载

HG/T 4493-2013 农业机械用轻型V带

本标准规定了农业机械用轻型V带(以下简称轻V带)的结构、型号和标记、截面尺寸、要求、试验方法、检验规则、标志、标签、包装、运输和贮存。本标准适用于水稻联合收割机、微耕机、园林机械等机械用V带。

Light V-belts for agricultural machinery

JIS K 6330-2:2013 橡胶和塑料软管和软管组合件.液压试验方法

Rubber and plastics hoses and hose assemblies.Part 2: Hydrostatic testing

DIN EN 13483:2013 已测定的燃料分配系统用带内部蒸气回收的橡胶和塑料软管及软管总成. 规范; 德文版本EN 13483-2013

Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification; German version EN 13483:2013

NF T47-293:2013 额定气压18巴及以下的蒸汽软管用对壳式耦合组件

Clamp type coupling assemblies for use with steam hoses rated for pressures up to 18 bar

NF P84-604*NF EN 495-5:2013 防水柔性板.低温弯曲性能测定.第5部分:屋顶防水用塑料和橡胶薄板

Flexible sheets for waterproofing - Determination of foldability at low temperature - Part 5: plastic and rubber sheets for roof waterproofing

EN 14420-8:2013 带合模装置的软管配件.第8部分:对称半管接头(吉尔曼系统)

This European Standard specifies dimensions, types of connections, quality of materials, marking requirements and testing requirements for hose fittings with symmetrical half couplings (Guillemin system), with mobile locking ring, for hose assemblies with a maximum working pressure of up to 10 bar1) with hose tails according to EN 14420-2 and clamp units according to EN 14420-3. Couplings in accordance with this document serve as link between hoses and connections to transport liquids, solids (e. g. powders, granules) except steam and liquid gas. The working temperature range is -20 °C up to +65 °C.

Hose fittings with clamp units - Part 8: Symmetrical half coupling (Guillemin system) (Incorporates Amendment A1: 2016)

EN 14420-7:2013 带合模装置的软管配件.第7部分:凸轮锁联接器

This European Standard specifies the design, materials, dimensions and marking requirements for cam locking couplings that serve as the link between hoses and connections to transport liquids, solids and gases, except liquid gas and steam. The couplings are capable of operating the pressure range -0,8 bar1) to 16 bar working pressure (for aluminium-cast-materials -0,8 bar to 10 bar) in a working temperature range of -20 °C up to +65 °C.

Hose fittings with clamp units - Part 7: Cam locking couplings

EN 14420-2:2013 带合模装置的软管配件.第2部分:软管尾部的软管侧面部件

This European Standard specifies requirements for the hose tail of hose fittings according to EN 14420-1 for use with clamp units according to EN 14420-3. Furthermore, it specifies materials for hose fittings with clamp units according to EN 14420-4 to EN 14420-8. Maximum working pressure is 25 bar1); maximum working temperature is 65 °C.

Hose fittings with clamp units - Part 2: Hose side parts of hose tail

EN 14420-1:2013 带合模装置的软管配件.第1部分:要求,安装和连接类型,名称和试验

This European Standard specifies requirements, types of fixing and connection, designation and testing for hose fittings with clamp units for hoses made of rubber/plastics or thermoplastics preferably for use with flammable and non-flammable products. It contains requirements for hose fittings to ensure that, when used appropriately, the user or third persons are not exposed to hazards from fire, explosions or acid burns, for example from mineral oils or chemicals, and that the environment is protected from pollution and other detritus. For maximum working pressure (WP) and temperature see 4.3. WARNING - Before decoupling of the quick coupling connections according to Parts 6, 7 and 8, the assembly should be at atmospheric pressure.

Hose fittings with clamp units - Part 1: Requirements, types of fixing and connection, designation and testing

EN 14420-6:2013 带合模装置的软管配件.第6部分:TW油罐车联接器

This European Standard specifies the fitting combinations, design, materials and dimensions for hose fittings with couplings for tank trucks (TW couplings). Couplings for tank trucks in accordance with this document are intended to link hoses with connections for the transport of liquids, solid matters and gases with the exception of liquid gas and steam. They can be employed in a working pressure range of -0,8 bar1) up to 16 bar at working temperatures of -20 °C up to +65 °C. Couplings for tank trucks for other operating conditions are subject to agreement. WARNING - Male and female dust couplings are pressure resistant plugs. They do not fulfil the function of a locking device, which should be installed in any case as long as the hose assembly is under pressure.

Hose fittings with clamp units - Part 6: TW tank truck couplings

EN 14420-5:2013 带合模装置的软管配件.第5部分:螺纹连接

This European Standard specifies requirements for hose fittings with clamp units according to EN 14420-1 with union nut and pipe thread according to EN ISO 228-1 as well as for hose tails according to EN 14420-2 with male pipe thread according to EN ISO 228-1. Maximum working pressure is 25 bar1); maximum working temperature is 65 °C.

Hose fittings with clamp units - Part 5: Threaded connections

BS EN 12316-2:2013 防水软板. 连接防剥离的测定. 防水塑料和橡胶薄板.

Flexible sheets for waterproofing. Determination of peel resistance of joints. Plastic and rubber sheets for roof waterproofing

BS EN 495-5:2013 防水软板. 低温环境下可折叠型的测定. 防水塑料和橡胶薄板.

Flexible sheets for waterproofing. Determination of foldability at low temperature. Plastic and rubber sheets for roof waterproofing

EN 14424:2013 带螺丝状套管的软管配件

This European Standard specifies the design, materials and dimensions of hose fittings with screwed ferrules for rubber and thermoplastics hoses for use with flammable and non-flammable liquids or gases, e. g. fuel dispensing hoses, liquid natural gas (LPG) hoses, tank truck hoses and hoses for liquid and gaseous chemicals. The nominal sizes covered are DN 13 to DN 40. Up to DN 25, the maximum working pressure is 25 bar1), and for DN 32 and DN 40 the maximum working pressure is 16 bar. The working temperature range is -20 °C to +65 °C, for LPG-usage it is -30 °C to +70 °C up to DN 25, and for LT-(low temperature) usage it is -50 °C to +70 °C.

Hose fittings with screwed ferrules

EN 14422:2013 液化石油气(LPG)输送软管用夹具型连接组件

This European Standard specifies the dimensions, designation, materials, marking and testing requirements for a range of hose fittings which may be used with rubber/plastic hoses for the transfer of liquefied petroleum gas, LPG, in liquid or vapour phase and natural gas. The maximum working pressure is 25 bar1). For normal operation the working temperature range is from -30 °C up to 70 °C and for low temperature operation (LT) it is from -50 °C up to 70 °C. The nominal size for hose fittings with internal and external threads is from DN 15 to DN 75 and for hose fittings with flanges DN 15 to DN 200. In addition to the fittings described in this European Standard, threaded connections according to EN 14420-5 as well as hose fittings with screwed ferrules according to EN 14424 up to DN 25 for LPG could be used.

Clamp type coupling assemblies for liquefied petroleum gas (LPG) transfer hoses

EN 14423:2013 额定压力到18BAR的蒸汽软管用夹具型连接组件

This European Standard specifies the design, materials and dimensions of fittings for clamp type coupling assemblies for use with nominal sizes DN 15 to DN 50 steam and hot water hoses. It covers assemblies up to a maximum working pressure of 18 bar (corresponding to a saturated steam temperature of 210 °C).

Clamp type coupling assemblies for use with steam hoses rated for pressures up to 18 bar

EN 13482:2013 柏油和沥青用橡胶软管及软管组件.规格

This European Standard specifies requirements for two types of hose and hose assembly (Type 1 and Type 2) identified by their maximum working pressures (Type 17 bar and Type 215 bar) and main use, i.e. Type 1 is for road and rail tanker use and Type 2 is for dockside use. The types are further divided into two classes related to the maximum temperature of the product to be conveyed (Class A up to 175 °C and Class B up to 200 °C). The hose constructions may be smooth bore (SB) or rough bore (RB). NOTE These types of hose or hose assemblies are not necessarily suitable for all types of petroleum based products or coal tar, or products containing coal tar.

Rubber hoses and hose assemblies for asphalt and bitumen - Specification

ANSI/UL 330a-2013 调剂易燃液体用软管和软管组件安全性标准

Standard for Safety for Hose and Hose Assemblies for Dispensing Flammable Liquids

ANSI/CSA HGV4.1-2013 氢配药系统

Hydrogen Dispensing Systems

ASTM D4637/D4637M-13 单层屋顶防渗护面中使用的乙丙三元橡胶薄板标准规格

1.1 This specification covers flexible sheet made from ethylene-propylene-diene terpolymer (EPDM) intended for use in single-ply roofing membranes exposed to the weather. The tests and property limits used to characterize the sheet are values to ensure minimum quality for the intended use. The sheet may be non-reinforced, fabric- or scrim-reinforced, or fabric-backed vulcanized rubber sheet. 1.2 In-place roof system design criteria, such as fire resistance, field seaming strength, material compatibility, and uplift resistance, among others, are factors that must be considered but are beyond the scope of this specification. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for EPDM Sheet Used In Single-Ply Roof Membrane