J17 齿轮与齿轮传动 标准查询与下载

DIN 3970:2010 圆柱齿轮检查用标准齿轮.齿轮毛坯和齿轮传动

Master gears according to this standard are used for the a single flank gear rolling inspection and double-flank rolling inspection of gears. This standard applies to spur and helical master gears for inspection of gears normal module 0.5 to 20 mm and helix angle up to 45?. The rolling inspection is described in the VDI/VDE guideline 2608 edition March 2001.

Master gears for checking cylindrical gears - Gear blanks and gearing

JIS B 1704:2010 锥形齿轮

This Standard specifies the chassification system for the geometrical accuracy of bevel gears and hypoid gears. Also, this Standard defines the terms related to the gear accuracy and specifies the structure and tolerances of the gear accuracy grade.

Bevel gear

DIN ISO 14635-2:2010 齿轮.FZG试验规程.第2部分:高级EP油支承荷载能力相关的FZG步骤负荷试验A10/16,6R/120(ISO 14635-2-2004)

The standard describes a step load test based on the FZG four square test rig suitable for the investigation of the load carrying capacity of high EP gear oils as typically used in automotive driveline systems and heavily loaded industrial gears.

Gears - FZG test procedures - Part 2: FZG step load test A10/16, 6R/120 for relative scuffing load-carrying capacity of high EP oils (ISO 14635-2:2004)

ANSI/AGMA 2003-2010 直齿伞齿轮齿,弧齿伞齿轮齿,螺旋伞齿轮齿的耐点蚀性和弯曲强度的评定

Presents a method for rating the pitting resistance and bending strength of bevel gear elements. Includes a detailed discussion of factors influencing gear survival, and calculation methods.

Rating the Pitting Resistance and Bending Strength of Generated Straight Bevel, Zerol Bevel and Spiral Bevel Gear Teeth

DIN ISO 18653:2009 齿轮.单个齿轮测量仪器的评价(ISO 18653:2003)

This International Standard specifies methods for the evaluation of measuring instruments used for gear measurements of involute, helix, pitch and runout. The evaluation is based on the measurement of different kinds of calibrated artifacts. This standard describes also the necessary estimation of measurement uncertainty with the use of these artifacts.

Gears - Evaluation of instruments for the measurement of individual gears (ISO 18653:2003)

KS B ISO 10300-3:2009 锥形齿轮承载能力的计算.第3部分:齿根强度的计算

이 표준은 최소 림 두께가 ≥3.5 mmn인 직선 베벨 기어, 헬리컬 베벨 기어, 스파이럴

Calculation of load capacity of bevel gears－Part 3：Calculation of tooth root strength

ISO 1122-1:1998/Cor 2:2009 齿轮名词术语.第1部分:与几何学相关的定义.技术勘误2

Vocabulary of gear terms - Part 1: Definitions related to geometry; Technical Corrigendum 2

ISO 4468:2009 齿轮滚刀.精度要求

This International Standard specifies requirements for the accuracy of general-purpose hobs of 0,5 module to 40 module. These hobs are intended for producing gears which conform to ISO 53 and ISO 54. This International Standard applies to hobs for spur and helical gears. It applies to solid (monobloc) and inserted blade hobs. The elemental features of hobs are graded according to accuracy, as follows: ⎯ Grade 4A; ⎯ Grade 3A; ⎯ Grade 2A: ⎯ Grade A; ⎯ Grade B; ⎯ Grade C; ⎯ Grade D. Grade 4A is the highest order of precision. In addition to the elemental tests for hobs, this International Standard gives permitted tolerances for composite tests that are taken along the cutting edges on the line of action. The two groups of tests are not equivalent and one shall choose between one or the other. If there was no previous agreement, the hob is regarded as belonging to the precision class specified if it satisfies one or the other of the two methods of inspection. NOTE The tolerances in this International Standard were determined for gear hobs whose dimensions conform to ISO 2490, but with certain precautions they can be applied to hobs not specified in this International Standard.

Gear hobs - Accuracy requirements

ISO/TR 10064-6:2009 检验实施规程.第6部分:斜齿轮测量方法

Code of inspection practice - Part 6: Bevel gear measurement methods

DIN 5481 Berichtigung 1:2009 锯齿形轴.技术勘误DIN 5481-2005

Serration shafts, Corrigendum to DIN 5481:2005-06

ISO 6336-3:2006/cor 1:2008 正齿轮和斜齿轮承载能力的计算.第3部分:轮齿弯曲强度的计算.技术勘误1

Calculation of load capacity of spur and helical gears - Part 3: Calculation of tooth bending strength; Technical Corrigendum 1

Calculation of load capacity of spur and helical gears - Part 3: Calculation of tooth bending strength; Technical Corrigendum 1

ISO 6336-2:2006/cor 1:2008 正齿轮和斜齿轮的负载能力计算.第2部分: 表面耐久性(蚀点)计算;技术勘误表1

Technical Corrigendum 1 to ISO 6336-2:2006 was prepared by Technical Committee ISO/TC 60, Gears, Subcommittee SC 2, Gear capacity calculation.

Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability (pitting) TECHNICAL CORRIGENDUM 1

ISO 6336-1:2006/cor 1:2008 正齿轮和斜齿轮的负载能力计算.第1部分: 基本原理，简介和一般影响因素;技术勘误表1

Technical Corrigendum 1 to ISO 6336-1:2006 was prepared by Technical Committee ISO/TC 60, Gears, Subcommittee SC 2, Gear capacity calculation

Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors TECHNICAL CORRIGENDUM 1

JIS B 1702-3:2008 圆柱齿轮.精确性.第3部分:与齿轮齿侧面的偏差和喷射模塑塑料齿轮的复合径向偏差相关的定义和容许值

この規格は，射出成形プラスチック円筒インポリュート歯車の精度体系について規定する。また，この規格は，歯車の歯の精度用語についての定義，歯車精度等級の構成並びに精度等級s級の単一ピッチ誤差，累積ビッチ誤差.全歯形誤差，全歯すじ誤差の許容値及び両歯面かみ合い誤差(両歯面全かみ合い誤差及び両歯面1ピッチかみ合い誤差)の許容値について規定する。

Cylindrical gears -- The accuracy -- Part 3: Definitions and allowable values of deviations relevant to corresponding flanks of the gear teeth and radial composite deviations of injection molding plastic gears

JIS B 1756:2008 齿轮.磨削后表面回火腐蚀的检验

This Standard specifies the inspection procedure, inspection criteria, classi- fication, etc. for detecting the localized overheating on ground gear surfaces by chemi- cai etching. The etch inspection according to this Standard is more sensitive to the surface hard- ness change than most hardness tests. Therefore, for the detection of surface temper after grinding, the inspection method in this Standard should be used. Although this Standard applies to steel gears, it may also apply to steel parts such as shafts, splines, bearings, but is not applicable to nitrided parts and stainless steels. This etch inspection shall be performed after grinding and before additional finishing operations. NOTES I In this Standard, this inspection is called "nital etch" and should not be confused with the conventional etch methods generally used to ob- serve metallographic structure. The International Standard corresponding to this Standard is as fol- lows. In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISOfIEC Guide 21. ISO 14104: 1995 Gears- Surface temper etch inspection after grind- ing (MOD)

Gears -- Surface temper etch inspection after grinding

ANSI/AGMA 2004-2008 齿轮材料和热处理手册

Provides information pertaining to ferrous and nonferrous materials used in gearing. Factors in material selection, including material forms, properties, and associated processing and heat treatments are discussed. Heat treating procedures used for gearing are covered in detail, including process descriptions, product specifications, process controls, and characteristics of heat treated gearing. Post heat treatment processes to meet gearing requirements are discussed.

Gear Materials and Heat Treatment Manual

ANSI/AGMA 6101-E-2008 封闭齿轮传动用组件的设计和选择(米制版)

Outlines the basic practices for the design and selection of components (other than gearing) which are used in commercial and industrial enclosed gear drives. Discusses bearings, bolting, keys, and the most recent theories on shafting among other components. Metric version of AGMA 6001-EXX.

Design and Selection of Components for Enclosed Gear Drives (Metric Edition)

ANSI/AGMA 6033-2008 船舶推进齿轮装置.第1部分:材料

Identifies commonly used alloy steels, heat treatment and inspection requirements for through hardened, case hardened and surface hardened gearing for main propulsion marine service over 1500 horsepower. Mechanical, metallurgical and nondestructive test requirements are provided for various heat treat processes and metallurgical quality grades of gearing.

Marine Propulsion Gear Units, Part 1 - Materials

ANSI/AGMA ISO 23509-A:2008 伞形和准双曲面齿轮几何学

Bevel and Hypoid Gear Geometry

ANSI/AGMA ISO 6336-6-A:2008 直齿轮和斜齿轮承载能力的计算.第6部分:变化负荷下工作寿命计算

Calculation of Load Capacity of Spur and Helical Gears - Part 6: Calculation of Service Life Under Variable Load