J17 齿轮与齿轮传动 标准查询与下载
共找到 632 条与 齿轮与齿轮传动 相关的标准，共 43 页
This standard provides definitions and parameters of cylindrical worm gear pairs with A,C,I,K or N flanks. It gives definitions and parameters of worm gear pairs, worms. worm wheels, deviations in tooth thicknrss and backlashes. For deviation apply DIN 3975-2.
Definitions and parameters on cylindrical worm gear pairs with rectangular crossing shafts - Part 1: Worm and worm wheel
- ICS
- 01.040.21;21.200
- CCS
- J17
- 发布
- 2017-09-00
- 实施
Gears -- Surface temper etch inspection after grinding, chemical method
- ICS
- 21.200
- CCS
- J17
- 发布
- 2017-05-22
- 实施
Cylindrical gears for general engineering and for heavy engineering -- Part 2: Module
- ICS
- 21.200
- CCS
- J17
- 发布
- 2017-05-22
- 实施
Gears. Surface temper etch inspection after grinding, chemical method
- ICS
- 21.200
- CCS
- J17
- 发布
- 2017-04-25
- 实施
- 2017-04-25
This document specifies procedures and requirements for the detection and classification of localized overheating on ground surfaces by chemical etch methods. The process described in this document is typically used on ground surfaces; however, it is also useful for the detection of surface anomalies that result from post-heat treatment machining such as hard turning, milling and edge breaking (deburring) processes. Surface metallurgical anomalies caused by carburization or decarburization are also readily detectable with this process. Some methods which have been used in the past are no longer recommended. Specifications are intended to be changed to use the methods in this document. These etchingmethods are more sensitive to changes in surface hardness than mosthardness testingmethods. This document applies to steel parts such as gears, shafts, splines and bearings. It is not applicable to nitrided parts and stainless steels. NOTE This process, although attimes called “nital etch”, is notintended to be confused with otherprocesses also known as “nital etch”. The surface temper etch procedure is performed after grinding and before additional finishing operations such as superfinishing, shot peening and honing.
Gears - Surface temper etch inspection after grinding, chemical method
- ICS
- 21.200
- CCS
- J17
- 发布
- 2017-04
- 实施
Bevel and hypoid gear geometry
- ICS
- 21.200
- CCS
- J17
- 发布
- 2016-11-30
- 实施
- 2016-11-30
Calculation of load capacity of spur and helical gears. Strength and quality of materials
- ICS
- 21.200
- CCS
- J17
- 发布
- 2016-08-31
- 实施
- 2016-08-31
Calculation of load capacity of spur and helical gears - Part 5: Strength and quality of materials
- ICS
- 21.200
- CCS
- J17
- 发布
- 2016-08
- 实施
Cylindrical gears -- ISO system of flank tolerance classification -- Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth
- ICS
- 21.200
- CCS
- J17
- 发布
- 2016-04-20
- 实施
Gears -- FZG test procedures -- Part 1: FZG test method A/8,3/90 for relative scuffing load-carrying capacity of oils
- ICS
- 21.200
- CCS
- J17
- 发布
- 2016-04-20
- 实施
Outboard motors. General safety requirement
- ICS
- 47.080
- CCS
- J17
- 发布
- 2016
- 实施
- 2017-01-01
Vocabulary of gear terms. Definitions related to worm gear geometry
- ICS
- 01.040.21;21.200
- CCS
- J17
- 发布
- 2015-09-30
- 实施
- 2015-09-30
Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength
- ICS
- 21.200
- CCS
- J17
- 发布
- 2015-07-28
- 实施
Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors
- ICS
- 21.200
- CCS
- J17
- 发布
- 2015-07-28
- 实施
Calculation of load capacity of spur and helical gears — Part 5: Strength and quality of materials
- ICS
- 21.200
- CCS
- J17
- 发布
- 2015-07-28
- 实施
Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability(pitting)
- ICS
- 21.200
- CCS
- J17
- 发布
- 2015-07-28
- 实施
Straight bevel gears for general engineering and heavy engineering — Modules and diametral pitches
- ICS
- 21.200
- CCS
- J17
- 发布
- 2015-04-10
- 实施
Straight bevel gears for general engineering and heavy engineering — Basic rack
- ICS
- 21.200
- CCS
- J17
- 发布
- 2015-04-10
- 实施
