共找到 1987 条与 压力容器 相关的标准,共 133 页
GB/T 20801 的本部分规定了压力管道系统的安全泄放装置、阻火器火灾紧急切断闻和机械联锁装置等安全保护装置和安全防护的基本要求。 本部分未规定的其他安全防护要求参见 GB/T 20801 其他部分以及国家现行有关规程、标准和规范的规定。 本部分适用于 GB/T 20801.1 范围界定的压力管道系统的安全防护。
Pressure piping code—Industrial piping—Part 6:Safeguarding
GB/T20801 的本部分规定了压力管道检验、检查和试验的基本安全要求。 本部分适用于 GB/T20801.1 范围界定的压力管道的检验、检查和试验。
Pressure piping code—Industrial piping—Part 5:Inspection and testing
1.1 本标准规定了公用管道(燃气管道和热力管道 )的材料、设计与计算、制作与安装、检验与试验、安全运行与维护等与安全相关的基本要求。 1.2 本标准适用于以下城镇燃气管道和城镇热力管道 : a) 燃气管道 :由门站、储配站、各类气源厂站等燃气厂站至用户之间或厂站之间公用性质的燃气管道及其附属设施。 附属设施包括线路阀室、调压站(含调压箱)、凝水缸等,详见图 1。 b) 热力管道 :由热源出口分界点至热用户 (民用或工业 )进口分界点之间,敷设在城镇范围内的蒸汽管道和热水管道及其附属设施,详见图 2。 其中蒸汽介质设计压力小于或等于 2.5 MPa,设计温度小于或等于 350 ℃ ;热水介质设计压力小于或等于 2.5 MPa,设计温度小于或等于200℃。 1.3 本标准不适用于以下燃气管道和热力管道 : a) 燃气系统中厂站内(调压站除外)的燃气管道和热力系统中厂站内(热力站和热分配站除外 )的热力管道 ; b) 工业用户内部燃气和热力管道(以厂界划分); c) 商业和居民用户内部燃气管道(以用户引入管阀门为界)和热力管道(以热力入口为界); d) 燃气和热力设备内部管道。 说明 :本标准适用的管道系统 本标准不适用的范围本标准包括的阀室及调压站 (含调压箱 )分输站至门站之间的燃气管道,应执行 GB/T34275,当敷设在城市建成区时,可参照本标准执行。
Pressure piping code—Utility piping
Fully-wrapped carbon fiber reinforced cylinders with an aluminum liner for theon-board storage of compressed hydrogen as a fuel for land vehicles
Technical specification for flange joints installation
Application guidance for safety accessories and instruments on pressure equipment
Selection and installation of pressure relief devices on pressure equipment
Safety assessment of in-service pressure vessels containing defects
Bellows expansion joints for pressure vessel
In-service pressure vessel inspection—Part 1: Hydrogenation reactor
本标准规定了气瓶外测法水压试验用标准瓶标定的方法及试验装置的基本要求。 本标准适用于气瓶外测法水压试验用标准瓶的标定。
Calibration method for calibrated cylinder used in water jacket hydrostatic test
Fitness-for-service assessment of pressure equipments
"Seamless steel gas cylinders—Part 1:Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa"
GB/T 5099的本部分规定了淬火后回火处理的抗拉强度小于1 100 MPa的钢质无缝气瓶(以下简称钢瓶)的型式和参数、技术要求、试验方法、检验规则、标志、涂敷、包装、运输、储存、产品合格证和批量检验质量证明书。 本部分适用于设计、制造公称工作压力不大于30 MPa,公称水容积为0.5 L~150 L,使用环境温度为-40 ℃~60 ℃,用于盛装压缩气体、高压液化气体或混合气体的可重复充装的钢瓶。 本部分不适用于车用气瓶和机器设备上附属的瓶式压力容器。
Seamless steel gas cylinders.Part 1:Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa
Seamless steel gas cylinders—Part 3:Normalized cylinders
GB/T 5099的本部分规定了正火或正火后回火处理的钢质无缝气瓶(以下简称钢瓶)的型式和参数、技术要求、试验方法、检验规则、标志、涂敷、包装、运输、储存、产品合格证和批量检验质量证明书。 本部分适用于设计、制造公称工作压力不大于15 MPa,公称水容积为0.5 L~150 L,使用环境温度为-20 ℃~60 ℃,用于盛装压缩气体或高压液化气体的可重复充装的钢瓶。 本部分不适用于车用气瓶和机器设备上附属的瓶式压力容器。
Seamless steel gas cylinders.Part 3:Normalized cylinders
Seamless steel gas cylinders—Part 4:Seamless stainless steel gas cylinders
Valve for cryogenic insulated cylinder—Part 1:Pressure regulating valve
Self-closing valves for LPG cylinders
Fully-wrapped carbon fiber reinforced cylinders with an aluminum liner for the on-board storage of compressed hydrogen as a fuel for land vehicles
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号