K12 带绝缘层电线 标准查询与下载

ANSI/ASTM D2307:2007 薄膜绝缘圆磁性导线的耐热性试验方法

This test method covers determination of the thermal endurance of film-insulated round magnet wire in air at atmospheric pressure. It is not applicable to magnet wire with fibrous insulation, such as cotton or glass. The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are provided for information only. This test method covers the evaluation of thermal endurance by observing changes in response to ac proof voltage tests. The evaluation of thermal endurance by observing changes in other properties of magnet wire insulation requires the use of different test methods. It is possible that exposure of some types of film insulated wire to heat in gaseous or liquid environments in the absence of air will give thermal endurance values different from those obtained in air. Consider this possibility when interpreting the results obtained by heating in air with respect to applications where the wire will not be exposed to air in service. It is possible that electric stress applied for extended periods at a level exceeding or even approaching the discharge inception voltage will change significantly the thermal endurance of film insulated wires. Under such electric stress conditions, it is possible that comparisons between materials will also differ from those developed using this method. This test method is similar to IEC 60172. Differences exist regarding specimen preparation. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Test Method for Thermal Endurance of Film-Insulated Round Magnet Wire

DIN EN 60317-0-6:2007 特种绕组线规范.第0-6部分:一般要求.玻璃纤维包浸树脂或浸清漆的裸圆铜线或漆包圆铜线

Specifications for particular types of winding wires - Part 0-6: General requirements - Glass-fibre wound resin or varnish impregnated, bare or enamelled round copper wire (IEC 60317-0-6:2001 + A1:2006); German version EN 60317-0-6:2001 + A1:2006

ANSI/ICEA S-70-547-2006 抗风化聚乙烯绝缘导线

This standard applies to the materials, constructions, and testing of weather-resistant polyethylene covered conductors rated at 75?C and 90?C normal service temperatures. Conductors covered under this standard are intended for the distribution of electrical energy under normal overhead (aerial) conditions and installations.

Weather-Resistant Polyethylene Covered Conductors

DIN EN 60317-0-5:2007 特种绕组线规范.第0-5部分:一般要求.玻璃纤维编织树脂或浸漆的裸或漆包扁铜线

Specifications for particular types of winding wires - Part 0-5: General requirements - Glass-fibre braided resin or varnish impregnated, bare or enamelled rectangular copper wire (IEC 60317-0-5:2006); German version EN 60317-0-5:2007

NF C31-678/A2:2007 特种绕组线规范.第28部分:180级聚酯(亚胺)漆包扁铜线

Specifications for particular types of winding wires - Part 28 : polyesterimide enamelled rectangular copper wire, class 180.

IEC 60317-28/AMD2:2007 特种绕组线规范.第28部分:180级聚酯酰亚胺漆包扁铜线.修改件2

This is Amendment 2 IEC 60317-28-1990 (Specifications pour types particuliers de fils de bobinage -Partie 28:Fil de section rectangulaire en cuivre emaille avec polyesterimide, classe 180)

Specifications for particular types of winding wires - Part 28: Polyesterimide enamelled rectangular copper wire, class 180; Amendment 2

NF C31-005/A2:2007 特种绕组线的规范.第0-5部分:一般要求.玻璃纤维编织的浸树脂或浸清漆裸扁铜线或漆包扁铜线

Specifications for particular types of winding wires - Part 0-5 : general requirements - Glass-fibre braided resin or varnish impregnated, bare or enamelled rectangular copper wire.

SANS 60317-4:2007 特种绕组线规范．第4部分：可焊聚氨基甲酸乙酯漆包圆铜线，220级

Specifies the requirements of solderable enamelled round copper winding wire of class 130 with a sole coating based on polyurethane resin.

Specifications for particular types of winding wires Part 4: Solderable polyurethane enamelled round copper wires, class 130

JB/T 6758.4-2007 换位导线 第4部分:耐热型漆包换位导线

JB/T 6758的本部分规定了耐热型漆包换位导线的一般要求。如聚酯纤维非织布带绝缘155级改性聚酯漆包换位导线及半硬导线（简称无纺布换位导线）；芳香族聚酰胺纸绝缘180级聚酯亚胺或200级聚酯亚胺/聚酰胺酰亚胺复合漆包换位导线及半硬导线（简称芳香族聚酰胺纸换位导线）等。漆包铜扁线铜导体既可以是普通软铜线，也可以是半硬铜线。 本部分应与JB/T 6758.1一起使用。

Continuously transposed conductors Part 4: Heat resistant continuously transposed conductors of enamelled copper wires

JB/T 6758.3-2007 换位导线 第3部分:无纸捆绑型缩醛漆包换位导线

JB/T 6758的本部分规定了无纸绝缘层捆绑型缩醛漆包换位导线的一般要求。换位线芯采用120级自粘性缩醛漆包铜扁线（热固性环氧树脂自粘层），网状绳捆型采用聚酯纤维绳捆绑，网格捆绑型采用聚酯纤维非织带、环氧树酯玻璃纤维布带或带孔型的绝缘纸带绕包，铜导体既可以是普通软铜线，也可以是半硬铜线。 本部分应与JB/T 6758.1一起使用。

Continuously transposed conductors Part 3: Less paper insulated netting-typed continuously transposed conductors of polyvinyl acetal enamelled copper wires

JB/T 6758.2-2007 换位导线 第2部分:纸绝缘缩醛漆包换位导线

JB/T 6758的本部分规定了纸绝缘缩醛漆包换位导线的一般要求。漆包扁线可以是120级缩醛漆包铜扁线，或在其外面再涂以热固性环氧棚旨自粘层的自粘性缩醛漆包铜扁线，铜导体既可以是普通软铜线，也可以是半硬铜线。本部分应与JB/T 6758.1一起使用。 纸绝缘缩醛漆包换位导线适用于油浸式变压器或电器的绕组线圈。

Continuously transposed conductors Part 2: Paper-insulated continuously transposed conductors of polyvinyl acetal enamelled copper wires

JB/T 6758.1-2007 换位导线 第1部分:一般规定

JB/T 6758的本部分规定了换位导线的型号、产品品种结构、技术要求、验收规则和包装标志。 本部分应与JB／T 6758后续各部分产品标准一起使用。 换位导线适用于各种油浸式、干式变压器、电抗器等电器绕组。

Continuously transposed conductors-Part 1: General requirements

BS EN 60317-0-5:2007 绕组线的特殊类型用规范.一般要求.玻璃纤维编制树脂或浸渍清漆的裸露或涂瓷釉的矩形铜线

This part of IEC 60317 specifies general requirements of glass-fibre braided resin or varnish impregnated, bare or enamelled rectangular copper wire. The range of nominal conductor dimensions is given in the relevant specification sheet. When reference is made to a winding wire according to IEC 60317-39 or IEC 60317-40 mentioned under Clause 2, the following information is given in the description: – reference to IEC specification; – nominal conductor dimensions in millimetres (width × thickness); – grade of coating and glass covering. The coating shall be characterised by the following grades of thickness: - BGL1, bare conductor with 1 braided layer of glass fibre - BGL2, bare conductor with 2 braided layers of glass fibre - grade 1 BGL1, enamelled grade 1 (grade 1) with 1 braided layer of glass fibre (BGL1) - grade 1 BGL2, enamelled grade 1 (grade 1) with 2 braided layers of glass fibre (BGL2) - grade 2 BGL1, enamelled grade 2 (grade 2) with 1 braided layer of glass fibre (BGL1) - grade 2 BGL2, enamelled grade 2 (grade 2) with 2 braided layers of glass fibre (BGL2)

Specifications for particular types of winding wires - General requirements - Glass-fibre braided resin or varnish impregnated, bare or enamelled rectangular copper wire

UL 2353 BULLETIN-2007 单层和多层绝缘绕组线UL安全性标准.评议提交截止日期:2007年11月5日

1.1 This Standard contains requirements for winding wire used in transformers without interleaved insulation; and solid insulation and insulated winding wire without interleaved insulation intended for use in accordance with the following standards: a) Standard for Information Technology Equipment, UL 60950; and the b) Standard for Information Technology Equipment - Safety - Part 1: General Requirements, UL 60950-1; or the c) Standard for Medical Electrical Equipment, Part 1: General Requirements for Safety, UL 60601-1. These requirements are not intended to prohibit use of this type of winding wire in equipment covered by the scope of other Standards when these requirements are determined to be compatible with those Standards. 1.2 These requirements cover winding wires with a diameter between 0.05 mm (0.002 inch) and 5.0 mm (0.2 inch). For other sizes and shapes, additional evaluation may be required. 1.3 The winding wire covered by this Standard shall also comply with the infrared analysis requirements in the Standard for Polymeric Materials - Short Term Property Evaluations, UL 746A. 1.4 This Standard does not cover solvent-based enamel coated magnet wire. See the Standard for Systems of Insulating Materials - General, UL 1446. If the desired useage of the single- and multi-layer Insulated winding wire is above Class 105 (A), additional testing of the insulation system would be required in accordance with UL 1446

UL Standard for Safety Single- and Multi-Layer Insulated Winding Wire COMMENTS DUE: November 5, 2007

ASTM D2307-07 薄膜绝缘磁性圆电线的热稳定性用标准试验方法

1.1 This test method covers determination of the thermal endurance of film-insulated round magnet wire in air at atmospheric pressure. It is not applicable to magnet wire with fibrous insulation, such as cotton or glass.1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are provided for information only.1.3 This test method covers the evaluation of thermal endurance by observing changes in response to ac proof voltage tests. The evaluation of thermal endurance by observing changes in other properties of magnet wire insulation requires the use of different test methods.1.4 It is possible that exposure of some types of film insulated wire to heat in gaseous or liquid environments in the absence of air will give thermal endurance values different from those obtained in air. Consider this possibility when interpreting the results obtained by heating in air with respect to applications where the wire will not be exposed to air in service.1.5 It is possible that electric stress applied for extended periods at a level exceeding or even approaching the discharge inception voltage will change significantly the thermal endurance of film insulated wires. Under such electric stress conditions, it is possible that comparisons between materials will also differ from those developed using this method.1.6 This test method is similar to IEC 60172. Differences exist regarding specimen preparation.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Thermal Endurance of Film-Insulated Round Magnet Wire

SAE AS22759A-2006 铜或铜合金的含氟聚合物绝缘电线

AS22759 specification covers fluoropolymer-insulated single conductor electrical wires made with tin-coated, silvercoated,or nickel-coated conductors of copper or copper alloy as specified in the applicable detail specification. Thefluoropolymer insulation may be polytetrafluoroethylene (PTFE), fluorinated ethylene propylene (FEP), polyvinylidenefluoride (PVF2), ethylene-tetrafluoroethylene copolymer (ETFE), or other fluoropolymer resin. The fluoropolymer may beused alone or in combination with other insulation materials.1.1 Part NumbersUnless otherwise specified part numbers are coded as in the following example (see 3.5.5 and 3.5.6):M22759/1 -22 -9M22759/1: Applicable detail specification designator (see 3.1)-22: Wire Size: (see 3.1)-9: Insulation color (see 3.5.5)1.2 Temperature Ratings of Finished WiresThe maximum conductor temperatures of the finished wires for continuous use are specified in the detail specifications.

(R) Wire, Electrical, Fluoropolymer-Insulated, Copper or Copper Alloy

IEC 60317-0-5:2006 特种绕组线规范.第0-5部分:一般要求.玻璃丝编织的、树脂的或清漆浸渍的、裸扁铜线或漆包扁铜线

This part of IEC 60317 specifies general requirements of glass-fibre braided resin or varnish impregnated, bare or enamelled rectangular copper wire. The range of nominal conductor dimensions is given in the relevant specification sheet. When reference is made to a winding wire according to IEC 60317-39 or IEC 60317-40 mentioned under Clause 2, the following information is given in the description: – reference to IEC specification; – nominal conductor dimensions in millimetres (width ×thickness); – grade of coating and glass covering. The coating shall be characterised by the following grades of thickness: - BGL1, bare conductor with 1 braided layer of glass fibre - BGL2, bare conductor with 2 braided layers of glass fibre - grade 1 BGL1, enamelled grade 1 (grade 1) with 1 braided layer of glass fibre (BGL1) - grade 1 BGL2, enamelled grade 1 (grade 1) with 2 braided layers of glass fibre (BGL2) - grade 2 BGL1, enamelled grade 2 (grade 2) with 1 braided layer of glass fibre (BGL1) - grade 2 BGL2, enamelled grade 2 (grade 2) with 2 braided layers of glass fibre (BGL2)

Specifications for particular types of winding wires - Part 0-5: General requirements - Glass-fibre braided, resin or varnish impregnated, bare or enamelled rectangular copper wire

KS C IEC 60317-25:2006 特种绕组线规范.第25部分:200级聚酰胺.酰亚胺包敷聚酯或聚酯酰亚胺漆包圆铝线

이 규격은 2중 코팅을 가진 분류 등급 200인 에나멜 원형 알루미늄선의 요구 사항을 규정

Specifications for particular types of winding wires-Part 25:Polyester or polyesterimide overcoated with polyamide-imideenamelled round aluminium wire, class 200

KS C IEC 60317-15:2006 特种绕组线规范.第15部分:180级聚酯酰亚胺漆包圆铝线

이 규격은 폴리에스터이미드(polyesterimide) 수지를 기본으로 단일 코팅한 분류

Specifications for particular types of winding wires-Part 15:Polyesterimide enamelled round aluminium wire, class 180

KS C IEC 60317-21:2006 特种绕组线规范.第21部分:155级聚酰胺包敷可软焊聚氨酯漆包圆铜线

이 규격은 이중 코팅을 가지고 분류 등급 155인 납땜 가능한 에나멜 원형 동선의 요구 사

Specifications for particular types of winding wires-Part 21:Solderable polyurethane enamelled round copperwire overcoated with polyamide, class 155