K74 灯具附件 标准查询与下载

BS EN 60238:2004+A2:2011 爱迪生螺口灯座

This International Standard applies to lampholders with Edison thread E14, E27 and E40, designed for connection to the supply of lamps and semi-luminaires* only. It also applies to switched-lampholders for use in a.c. circuits only, where the working voltage does not exceed 250 V r.m.s. This standard also applies to lampholders with Edison thread E5 designed for connection to the supply mains of series connected lamps, with a working voltage not exceeding 25 V, to be used indoors, and to lampholders with Edison thread E10 designed for connection to the supply mains of series connected lamps, with a working voltage not exceeding 60 V, to be used indoors or outdoors. It also applies to lampholders E10 for building-in, for the connection of single lamps to the supply. These lampholders are not intended for retail sale. As far as it reasonably applies, this standard also covers lampholders other than lampholders with Edison thread designed for connection of series-connected lamps to the supply. NOTE This type of lampholder is for example used in Christmas tree lighting chains. As far as it reasonably applies, this standard also covers adapters. This standard also covers lampholders which are, wholly or partly, integral with a luminaire or intended to be built into appliances. It covers the requirements for the lampholder only. For all other requirements, such as protection against electric shock in the area of the terminals or of the lamp cap, the requirements of the relevant appliance standard shall be observed and tested after building into the appropriate equipment, when that equipment is tested according to its own standard. Such lampholders as well as lampholders provided with a snap-on outer shell, for use by luminaire manufacturers only, are not for retail sale. This standard applies to lampholders to be used indoors or outdoors in residential as well as in industrial lighting installations. It also applies to candle lampholders. In locations where special conditions prevail, as for street lighting, on board ships, in vehicles and in hazardous locations, e.g. where explosions are liable to occur, special constructions may be required. NOTE 1 This standard does not apply to three-light lampholders E26d. NOTE 2 This standard is based on the following data relative to lamps for general lighting service: – caps E14 are used for lamps with a current not exceeding 2 A; – caps E27 are used for lamps with a current not exceeding 4 A; – caps E40 are used for lamps with a current not exceeding 16 A. NOTE 3 If the nominal voltage of the supply does not exceed 130 V, the maximum current for caps E40 is 32 A (see 4.5 and 5.3). NOTE 4 Where lampholders are used in luminaires, their maximum operating temperatures are specified in IEC 60598.

Edison screw lampholders

UL 879B BULLETINS-2005 电光标志部件标准(STP 879的修订本)/注:ANSI/UL 879-2005的修订本*

Proposed revisions to requirements for the Standard for Electric Sign Components, STP 879.

Standard for Electric Sign Components (revisions to STP 879) / Note: revision of ANSI/UL 879-2005 *

NF C71-247-3/A1:2005 灯控制装置.第2-3部分:荧光灯用交流电子镇流器的特殊要求

Lamp controlgear - Part 2-3 : particular requirements for a.c. supplied electronic ballasts for fluorescent lamps.

UL 879A BULLETINS-2005 电光标志部件标准(STP 879的修订本)/注:ANSI/UL 879-2005的修订本*

Proposed revisions to requirements for the Standard for Electric Sign Components, STP 879.

Standard for Electric Sign Components (revisions to STP 879) / Note: revision of ANSI/UL 879-2005 *

IEC 60061-3:2005 灯头、灯座及检验其安全性和互换性的量规.第3部分:量规

IEC 60061 Lamp caps and holders together with gauges for the control of interchangeablility and safety consists of four parts: Part 1: Lamp caps, Part 2: Lampholders, Part 3: Gauges, Part 4: Guidelines and general information. Each part is independent of

Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 3: Gauges

IEC 60061-2:2005 灯头、灯座及检验其安全性和互换性的量规.第2部分:灯座

This International Standard contains the recommendations of the IEC in regard to lamp caps and holders in general use today, together with relevant gauges, with the object of securing international interchangeability. The gauges illustrated, although generally accepted in principle, are not necessarily the only form in which they can be made.

Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 2: Lampholders

IEC 60061-4:2005 灯头、灯座及检验其安全性和互换性的量规.第4部分:指南和一般信息

IEC 60061 Lamp caps and holders together with gauges for the control of interchangeablility and safety consists of four parts: Part 1: Lamp caps, Part 2: Lampholders, Part 3: Gauges, Part 4: Guidelines and general information. Each part is independent of

Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 4: Guidelines and general information

ANSI C136.24-2005 非锁定(按钮)式光控制器

Covers the electrical and mechanical interchangeability of nonlocking type photocontrols for mounting within a roadway or off-roadway luminaire, herein called "controls." These controls are commonly called "button" photocontrols.

Nonlocking (Button) Type Photocontrols

ANSI C82.6-2005 灯镇流器.高亮度放电灯用镇流器.测量方法

This standard describes the procedures to be followed and the precautions to be taken in measuring performance of ballasts for high-intensity discharge (HID) lamps.

Lamp Ballasts - Ballasts for High Intensity Discharge Lamps - Method of Measurement

ANSI/IEC C81.63:2005 电灯头和灯座用量规的规范

C81.63 sets forth the specifications for gauges for bases (caps) and lampholders for electric lamps.

Specifications for Gauges for Electric Lamp Bases (Caps) and Lampholders

ANSI/UL 542-2005 荧光灯用起动器的安全标准

This proposal includes revisions to the requirements based on comments received to the ballot dated March 4, 2005.

Standard for Fluorescent Lamp Starters

UL 496-2004 灯座

1.1 The requirements of this standard cover holders and connectors for electric lamps, including incandescent, fluorescent, and other electric-discharge-type lamps, rated as indicated in Clause 6, to be used in accordance with the Canadian Electrical Code (CEC), C22.1, Part I, and the National Electrical Code (NEC), ANSI/NFPA-70. 1.2 These requirements cover screw lampholders, including those intended to be mounted directly on an outlet-box, lampholders for special uses, lampholders for electric signs, and adapters that convert one lampholder size to another. 1.3 These requirements also cover holders for automatic starters used with fluorescent lamps. 1.4 These requirements also cover indicator lamps. 1.5 These requirements also cover lampholder inserts. 1.6 These requirements also cover naval-use lampholders. See Supplement sb. 1.7 These requirements do not cover fluorescent self-ballasted lamps and fluorescent lamp adapters covered in UL 1993. 1.8 These requirements do not cover seasonal-lighting lampholders, which are covered in UL 588 and CSA C22.2 No. 37. 1.9 These requirements do not cover electrode receptacles for use in gas-tube signs, which are covered in UL 879 and CSA C22.2 No. 34. 1.10 These requirements do not cover devices requiring a cross-bar, mounting strap, or other mounting means; such devices are considered to be luminaries. 1.11 These requirements do not cover nightlights, which are covered in UL 1786 and CSA C22.2 No. 12. This is the Twelfth Edition of ANSI/UL 496. It contains requirements from the Eleventh Edition of UL 496 and from the Eighth Edition of UL 542 and has been harmonized with the requirements of Canada.

Lampholders

BS EN 60399:2004+A1:2008 有灯罩座环的灯座筒螺纹

Barrel thread for lampholders with shade holder ring

BS EN 60838-1:2004+A2:2011 不同种类的灯座.第1部分:一般要求和试验

This part of IEC 60838 applies to lampholders of miscellaneous types intended for building-in (to be used with general purpose light sources, projection lamps, floodlighting lamps and street-lighting lamps with caps as listed in annex A) and the methods of test to be used in determining the safe use of lamps in lampholders. This part of IEC 60838 also covers lampholders which are integral with a luminaire. It covers the requirements for the lampholder only. This part of IEC 60838 also covers lampholders integrated in an outer shell and dome similar to Edison screw lampholders. Such lampholders are further tested in accordance with the following subclauses of IEC 60238: 8.4; 8.5; 8.6; 9.3; 10.7; 11; 12.2; 12.5; 12.6; 12.7; 13; 15.3; 15.4; 15.5 and 15.9. Requirements for lampholders for tubular fluorescent lamps, Edison screw lampholders and bayonet lampholders are covered by separate standards.

Miscellaneous lampholders. Part 1: General requirements and tests

BS EN 60838-1:2004 各式灯座.第1部分:一般要求和试验

This part of IEC 60838 applies to lampholders of miscellaneous types intended for building-in (to be used with general purpose light sources, projection lamps, floodlighting lamps and street-lighting lamps with caps as listed in annex A) and the methods of test to be used in determining the safe use of lamps in lampholders. This part of IEC 60838 also covers lampholders which are integral with a luminaire. It covers the requirements for the lampholder only. This part of IEC 60838 also covers lampholders integrated in an outer shell and dome similar to Edison screw lampholders. Such lampholders are further tested in accordance with the following subclauses of IEC 60238: 8.4; 8.5; 8.6; 9.3; 10.7; 11; 12.2; 12.5; 12.6; 12.7; 13; 15.3; 15.4; 15.5 and 15.9. Lampholders designed with a barrel thread for shade holder rings should comply with IEC 60399. Requirements for lampholders for tubular fluorescent lamps, Edison screw lampholders and bayonet lampholders are covered by separate standards.

Miscellaneous lampholders - General requirements and tests

BS EN 60838-1:2004+A1:2008 各式灯座.试验和一般要求

This part of IEC 60838 applies to lampholders of miscellaneous types intended for building-in (to be used with general purpose light sources, projection lamps, floodlighting lamps and street-lighting lamps with caps as listed in annex A) and the methods of test to be used in determining the safe use of lamps in lampholders. This part of IEC 60838 also covers lampholders which are integral with a luminaire. It covers the requirements for the lampholder only. This part of IEC 60838 also covers lampholders integrated in an outer shell and dome similar to Edison screw lampholders. Such lampholders are further tested in accordance with the following subclauses of IEC 60238: 8.4; 8.5; 8.6; 9.3; 10.7; 11; 12.2; 12.5; 12.6; 12.7; 13; 15.3; 15.4; 15.5 and 15.9. Requirements for lampholders for tubular fluorescent lamps, Edison screw lampholders and bayonet lampholders are covered by separate standards.

Miscellaneous lampholders - General requirements and tests

JIS C 7709-0 AMD 1:2004 可转换性和安全控制量规及灯头和灯座.第0部分:一般信息(修改件1)

この追補は，JIS C 7709-0:1997が, 2004年11月20日付けで改正されたことに伴って発行されたものである。

Lamp caps and holders together with gauges for the control of interchangeability and safety Part 0: General information (Amendment 1)

JIS C 7709-1 AMD 1:2004 可转换性和安全控制量规及灯头和灯座.第1部分:灯头(修改件1)

この追補は，JIS C 7709-1:1997が。2004年11月20月付けで改正されたことに伴って発行されたものである。

Lamp caps and holders together with gauges for the control of interchangeability and safety Part 1: Lamp caps (Amendment 1)

JIS C 7709-2 AMD 1:2004 可转换性和安全控制量规及灯头和灯座.第2部分:灯座(修改件1)

この追補は,JIS C 7709-2:1997が，2004年11月20日付けで改正されたことに伴って発行されたものである。

Lamp caps and holders together with gauges for the control of interchangeability and safety Part 2: Lampholders (Amendment 1)

JIS C 7709-3 AMD 1:2004 可转换性和安全控制量规及灯头和灯座.第3部分:量规(修改件1)

この追補は，JIS C 7709-3:1997が, 2004年11月20日付けで改正されたことに伴って発行きれたものである。

Lamp caps and holders together with gauges for the control of interchangeability and safety Part 3: Gauges (Amendment 1)