K84 蓄电能装置 标准查询与下载

SAE J1798-2008 电车蓄电池模块的性能评估用推荐实施规程

This SAE Recommended Practice provides for common test and verification methods to determine Electric Vehicle battery module performance. The document creates the necessary performance standards to determine (a) what the basic performance of EV battery modules is; and (b) whether battery modules meet minimum performance specification established by vehicle manufacturers or other purchasers. Specific values for these minimum performance specifications are not a part of this document.

Recommended Practice for Performance Rating of Electric Vehicle Battery Modules

DIN EN 60086-4:2008 原电池.第4部分:锂电池的安全

Primary batteries - Part 4: Safety of lithium batteries (IEC 60086-4:2007); German version EN 60086-4:2007

DIN EN 50342-2:2008 铅酸起动器电池.第2部分:电池尺寸和终端标记

Lead-acid starter batteries - Part 2: Dimensions of batteries and marking of terminals; German version EN 50342-2:2007

BS EN 60254-2:2008 铅酸牵引蓄电池组.蓄电池和端子尺寸及电池的极性标记

This part of IEC 60254 is applicable to lead-acid traction batteries used as power sources for electric propulsion. The object of the present standard is to specify: – the maximum external (overall) dimensions of traction battery cells, that is, the width, the height and the length; – the form of the marking of traction battery cell polarity and dimensions of corresponding symbols; – the basic dimensions of some commonly used traction battery terminals designed to connect output cables to the battery; – the dimensions of cells commonly used in Asia and North America.

Lead-acid traction batteries - Part 2: Dimensions of cells and terminals and marking of polarity on cells

SANS 60254-2:2008 铅酸动力电池.第2部分:电池尺寸、接线端及对电池极性标记

Applicable to lead-acid traction batteries used as power sources for electric propulsion. Specifies the maximum external (overall) dimensions of traction battery cells, the form of the marking of traction battery cell polarity and dimensions of correspon

Lead-acid traction batteries Part 2: Dimensions of cells and terminals and marking of polarity on cells

SANS 60095-4:2008 起动用铅酸蓄电池.第4部分:重型车辆电池体积

Applicable to lead-acid batteries used for starting, lighting and ignition of heavy trucks, commercial vehicles, buses and agricultural trucks.

Lead-acid starter batteries Part 4: Dimensions of batteries for heavy vehicles

SAE J2288-2008 电车蓄电池模块的寿命周期测试

This SAE Recommended Practice defines a standardized test method to determine the expectedservice life, in cycles, of electric vehicle battery modules. It is based on a set of nominal or baseline operating conditions in order to characterize the expected degradation in electrical performance as a function of life and to identify relevant failure mechanisms where possible. Accelerated aging is not included in the scope of this procedure, although the time compression resulting from continuous testing may unintentionally accelerate battery degradation unless test conditions are carefully controlled. The process used to define a test matrix of accelerated aging conditions based on failure mechanisms, and to establish statistical confidence levels for the results, is considered beyond the scope of this document. Because the intent is to use standard testing conditions whenever possible, results from the evaluation of different technologies should be comparable. End-of-life is determined based on module capacity and powerratings. This may result in a measured cycle life different than that which would be determined based on actual capacity; however, this approach permits a battery manufacturer to make necessary tradeoffs between power and energy in establishing ratings for a battery module. This approach is considered appropriate for a mature design or production battery. It should be noted that the procedure defined in this document is functionally identical to the USABC Baseline Life Cycle Test Procedure.

Life Cycle Testing of Electric Vehicle Battery Modules

SAE J1797-2008 电车蓄电池模块的包装用推荐实施规程

This SAE Recommended Practice provides for common battery designs through the description of dimensions, termination, retention, venting system, and other features required in an electric vehicle application. The document does not provide for performance standards. Performance will be addressed by SAE J1798. This document does provide for guidelines in proper packaging of battery modules to meet performance criteria detailed in J1766.

Recommended Practice for Packaging of Electric Vehicle Battery Modules

JIS C 8712 ERRATUM 1:2008 勘误表

ERRATUM

JIS C 8708 ERRATUM 1:2008 勘误表

ERRATUM

IEEE 1562-2007 单机光电(PV)设备中串联电池及电池尺寸用指南

This guide provides information to assist in sizing the array and battery of a stand-alone photovoltaic system. Systems considered in this guide consist of PV as the only power source and a battery for energy storage. These systems also commonly employ controls to protect the battery from being over- or undercharged, and may employ a power conversion subsystem (inverter or converter). This guide is applicable to all stand-alone PV systems where PV is the only charging source. This guide does not include PV hybrid systems nor grid-connected systems. This guide covers lead-acid batteries only; nickel-cadmium and other battery types are not included. This guide does not include the sizing of the system controller, inverter, wiring, or other system components.

IEEE Guide for Array and Battery Sizing in Stand-Alone Photovoltaic (PV) Systems

ANSI/IEEE 1561:2007 远程混合电力系统中酸性铅蓄电池的性能和寿命的优化用指南

This guide provides rationale and guidance for operating lead-acid batteries in remote hybrid power systems, taking into consideration system loads and the capacities of the system's renewable-energy generator(s), dispatchable generator(s), and battery(s). It also provides guidance for selecting an appropriate lead-acid battery technology for various system operating strategies.

Guide for Optimizing the Performance and Life of Lead-Acid Batteries in Remote Hybrid Power Systems

GJB 6274-2008 电动力鱼雷用锌银蓄电池(组)通用规范

本规范规定了电动力鱼雷用锌银蓄电池(组)(以下简称“蓄电池 ” 或“蓄电池组”)通用要求。 本规范适用于各型电动力鱼雷用锌银蓄电池(组)的研制、生产和交付检验。

General specification for silver-zinc storage batteries for electric-torpedo

JB/T 7630.1-2008 铅酸蓄电池超细玻璃纤维隔板

JB/T 7630的本部分规定了铅酸蓄电池超细玻璃纤维隔板(以下简称隔板)的定义、隔板分类、命名标记、要求、测定方法、检验规则、标志、包装、运输和贮存等。 本部分适用于铅酸蓄电池隔板。

Glass micro-fiber separators for lead-acid batteries

JB/T 7630.5-2008 铅酸蓄电池微孔聚乙烯隔板

JB/T 7630的本部分规定了铅酸蓄电池微孔聚乙烯隔板(以下简称隔板)的定义、隔板分类、命名与标记、要求、测定方法、检验规则、标志、包装、运输和贮存等。 本部分适用于铅酸蓄电池隔板。

Microporous polyethylene separators for lead-acid batteries

JB/T 7630.4-2008 铅酸蓄电池熔喷聚丙烯隔板

JB/T 7630的本部分规定了铅酸蓄电池熔喷聚丙烯隔板(以下简称隔板)的定义、隔板分类、命名与标记、要求、测定方法、检验规则、标志、包装、运输和贮存等。 本部分适用于铅酸蓄电池隔板。

Melt-spray polypropylene separators for lead-acid batteries

JB/T 7630.2-2008 铅酸蓄电池微孔橡胶隔板

JB/T 7630的本部分规定了铅酸蓄电池微孔像胶隔板(以下简称隔板)的定义、隔板分类、命名与标记、要求、测定方法、检验规则、标志、包装、运输和贮存等。 本部分适用于铅酸蓄电池隔板。

Microporous rubber separators for lead-acid batteries

JB/T 7630.3-2008 铅酸蓄电池烧结聚氯乙烯隔板

JB/T 7630的本部分规定了铅酸蓄电池烧结聚氯乙烯隔板(以下简称隔板)的定义、隔板分类、命名与标记、要求、测定方法、检验规则、标志、包装、运输和贮存等。 本部分适用于铅酸蓄电池隔板。

Sintered polyvinyl chloride separators for lead-acid batteries

IEC 60095-4:2008 铅酸起动器蓄电池组.第4部分:重型车用蓄电池组的尺寸

This part of IEC 60095 is applicable to lead-acid batteries used for starting, lighting and ignition of heavy trucks, commercial vehicles, busses and agricultural trucks. The object of the present standard is to specify global requirements of the main dimensions of starter batteries for Europe, North America and East Asia. This International Standard comprises 12 types of "preferred types" of batteries. The standard specifies dimensions of 4 types of batteries each for the Europe (types A, B, C and D2), North America (4D, 8D, 31T, 31A) and East Asia (E41, F51, G51, H52) regions. For future new developments of heavy vehicles it is strongly recommended to use only batteries from this standard. Several other types of batteries exist under the standards of national or regional organisations. They are not included in this International Standard.

Lead-acid starter batteries - Part 4: Dimensions of batteries for heavy vehicles

IEC 60254-2:2008 铅酸牵引蓄电池组.第2部分:蓄电池和端子尺寸及电池的极性标记

This part of IEC 60254 is applicable to lead-acid traction batteries used as power sources for electric propulsion.

Lead-acid traction batteries - Part 2: Dimensions of cells and terminals and marking of polarity on cells