L05 可靠性和可维护性 标准查询与下载

IEC 60605-3-6:1996 设备可靠性试验 第3部分:推荐试验条件 第6节:试验循环6:室外移动设备 粗模拟

Describes test conditions, which are applicable to outdoor transportable equipment operating only while in a stationary position in a climate belonging to the group of climates described as "warm temperature" in IEC 721-2-1.

Equipment reliability testing - Part 3: Preferred test conditions - Section 6: Test cycle 6: Outdoor transportable equipment - Low degree of simulation

NF C20-300-2:1996 可靠性管理.第2部分:可靠性计划要素和任务

Dependability management. Part 2 : dependability programme elements and tasks.

IEC 60605-3-5:1996 设备可靠性试验 第3部分:推荐试验条件 第5节:试验循环5:地面移动设备 粗模拟

This section of IEC 605-3 is applicable to direct current (d.c.) powered mobile equipment. The equipment is operated while being transported, for example in or on a verhicle but does not form part of the vehicle, and is not designed to be installed perma

Equipment reliability testing - Part 3: Preferred test conditions - Section 5: Test cycle 5: Ground mobile equipment - Low degree of simulation

IEC 60300-3-9:1995 可信性管理 第3部分:应用指南 第9节:技术的系统风险分析

Provides guidelines for selecting and implementing risk analysis techniques, primarily for risk assessment of technological systemes. Aims at ensuring quality and consistency in the planning and execution of risk analyses and the presentation of results

Dependability management - Part 3: Application guide - Section 9: Risk analysis of technological systems

SJ/T 10667-1995 钎焊、封接的代号及标注方法

本标准规定了钎焊和封接的代号及其标注方法，适用于电子技术产品钎焊和封接件的图样绘制以及有关技术文件的编制。

Symbol and notation for brazing,soldering and sealing

SJ/T 10670-1995 表面组装工艺通用技术要求

本标准规定了电子技术产品采用表面组装技术(SMT)时应遵循的基本工艺要求。 本标准适用于以印制板(PCB)为组装基板的表面组装组件(SMA)的设计和制造。对采用陶瓷或其它基板的SMA的设计和制造也可参照使用。

General requirements for workmanship of surface mount technology

SJ/T 10666-1995 表面组装组件的焊点质量评定

本标准适用于对表面组装组件焊点的质量评定。

Quality assessment of soldered joints of SMA

SJ 20509-1995 电子设备微生物劣化的起因与控制技术手册

Technologic handbook for origin and control of microbial deterioration in electronics

IEC 60706-6:1994 设备维修性指南 第6部分:第9节:维修性评估的统计方法

Specifies techniques covering some quantitative aspects of maintainability engineering in various phases of the system life cycle. Is applicable to the tasks of maintainability allocation, maintainability demonstration and maintainability data evaluation

Guide on maintainability of equipment - Part 6; section 9: Statistical methods in maintainability evaluation

IEC 60706-5:1994 设备维修性指南 第5部分:第4节:诊断试验

Provides guidance for the early consideration of testability aspects in design and development and assists in determining effective test procedures as an integral part of operation and maintenance. Is applicable to all categories of equipment in their co

Guide on maintainability of equipment - Part 5, Section 4: Diagnostic testing

NF C20-341:1994 可靠性分析技术.可靠性方块图法

Analysis techniques for dependability. Reliability block diagram method.

IEC 60605-2:1994 设备可靠性试验 第2部分:试验周期的设计

Provides a general procedure for design of test cycles, where no applicable preferred test cycles can be found in IEC 605-3. Applies to the design of operating and environmental test cycles referred to in 8.1 and 8.2 of IEC 605-1. The resulting test cycl

Equipment reliability testing - Part 2: Design of test cycles

NF C20-300-1:1994 可靠性管理.第1部分:可靠性程序管理

Dependability management. Part 1 : dependability programme management.

SJ/T 9167.18-1993 聚合材料制造的零部件

1.1 这些要求规定的是适用于已由聚合材料模压或制造的零部件的一个程序。并描述了预定对用于聚合物部件的材料通过处理、模塑或制造以及发货等控制提供溯源的材料识别控制系统。还为可能影响起火、触电或人身伤害的危险的配料或简单混合操作的可接受程度提供了指南。 1.2 本程序是预定借助于在零部件上、或零部件发货箱上或随零部件放在包装箱内清单上的识别标记，对材料的标识提供快速的确认。本程序的目的是为了排除在最终产品中使用身份不明的聚合材料并减小由于不正确的使用材料造成的实际问题的可能性。 1.3 本标准所涉及的聚合物材料识别程序是为了对在工厂安装在不同的设备中的元器件材料的的组成提供溯源，在那里将确定组装的合格与否。 1.4 本程序预定不用于对现场安装的聚合材料的溯源。 1.5 本标准不涉及给定零部件性能要求，金属镀层或漆料涂层零部件的评定要求和方法被包括在UL 746C《电气设备用聚合材料的评定》和UL 746A《聚合材料短时性能的评定》标准的对聚合材料的要求中。对于涉及零部件或组装件的性能要求应参照有关专门的产品标准。

Polymeric materials-fabricated parts

IEC 60300-3-2:1993 可信性管理 第3部分:应用指南 第2节:现场可信性数据收集

Dependability management; part 3: application guide; section 2: collection of dependability data from the field

DIN IEC 61123:1993 可靠性试验.成功率验证试验方案

The document specifies procedures for applying and preparing compliance test plans for success ratio or failure ratio. The procedures are based on the assumption that each trial is statistically independent.

Reliability testing; compliance test plans for success ratio; identical with IEC 61123:1991

SJ 20375-1993 军用电子测试设备通用规范.可靠性试验要求和方法

General specification for military electronic test equipment.Requirements and methods for reliability test

IEC 60300-1:1993 可信性管理 第1部分:可信性方案管理

Dependability management; part 1: dependability programme management

IEC 60605-3-3:1992 设备可靠性试验 第3部分:推荐试验条件 第3节:试验循环3:固定使用的有部分气候防护场所的设备 粗模拟

Describes applicability, basic assumptions underlying the severities, pre-exposure tests, test cycle, and relevant test time.

Equipment reliability testing; part 3: preferred test conditions; section 3: test cycle 3: equipment for stationary use in partially weatherprotected locations; low degree of simulation

IEC 61123:1991 可靠性试验 成功率验证试验方案

Gives terms and definitions and a list of symbols. Describes application, general decision criteria and three different test plans.

Reliability testing; compliance test plans for success ratio