L14 电位器 标准查询与下载

IEC 60393-5:2015 电子设备用电位器 第5部分:分规范:单圈旋转线绕和非线绕低功率电位器

This part of IEC 60393 applies to single-turn rotary low-power wirewound and non-wirewound potentiometers, with a rated dissipation less than to 10 W. These potentiometers are primarily intended for use in electronic equipment. This part of IEC 60393 prescribes preferred ratings and characteristics and selects from IEC 60393-1, appropriate quality assessment procedures, tests and measuring methods. It provides general performance requirements for this type of potentiometer. This standard gives the minimum performance requirements and test severities.

Potentiometers for use in electronic equipment - Part 5: Sectional specification - Single-turn rotary low-power wirewound and non-wirewound potentiometers

GJB 917A-2011 线绕预调电位器通用规范

本规范规定了线绕预调电位器的分类、技术要求、试验方法、质量保证规定、交货准备等。 本规范适用于螺杆驱动和单圈旋转的线绕预调电位器（以下简称电位器）。这些电位器的上限类别温度分别为125℃和150℃，满负荷工作（此时，整个电阻体都已接入）的最高环境温度分别为70℃和85℃（见3.4）。电位器的阻值允许偏差为±5%。

General specification for wire-wounded preset potentiometers

GJB 918A-2011 非线绕预调电位器通用规范

本规范规定了非线绕预调电位器的通用要求、质量保证规定等。 本规范适用于螺杆驱动和单圈旋转的非线绕预调电位器（以下简称电位器）。这些电位器的上限类别温度分别为125℃和150℃，满负荷工作（此时，整个电阻体都已接入）的最高环境温度分别为70℃和85℃（见图2）。电位器的阻值允许偏差为±10%。

General specification for nonwire-wounded preset potentiometers

DIN EN 60393-1:2010 电子设备用电位器.第1部分:通用规范(IEC 60393-1-2008).德文版本EN 60393-1-2009

This part of IEC 60393 is applicable to all types of resistive potentiometers, including lead-screw actuated types, presets, multi-turn untis, etc. to be used in electronic equipment. It establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose.

Potentiometers for use in electronic equipment - Part 1: Generic specification (IEC 60393-1:2008); German version EN 60393-1:2009

BS EN 60393-1:2009 电子设备用电位器.通用规范

This part of IEC 60393 is applicable to all types of resistive potentiometers, including leadscrew actuated types, presets, multi-turn units, etc. to be used in electronic equipment. It establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose. It has been mainly written, and the test methods described, to conform to the widely used single-turn rotary potentiometer with an operating shaft. For other types of potentiometers: • the angle of rotation may be several turns; • the reference to an operating shaft shall apply to any other actuating device; • the angular rotation shall be taken to mean mechanical travel of the actuating device; • a value for force shall be prescribed instead of a value for torque if the actuating device moves in a linear instead of a rotary manner. These alternative prescriptions will be found in the sectional or detail specification. When a component is constructed as a variable resistor, i.e. as a two-terminal device, the detail specification shall prescribe the modifications required in the standard tests.

Potentiometers for use in electronic equipment - Generic specification

IEC 60393-1:2008 电子设备用电位器.第1部分:总规范

This part of IEC 60393 is applicable to all types of resistive potentiometers, including lead- screw actuated types, presets, multi-turn units, etc. to be used in electronic equipment. It establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose. It has been mainly written, and the test methods described, to conform to the widely used single-turn rotary potentiometer with an operating shaft. For other types of potentiometers: ~ the angle of rotation may be several turns; ~ the reference to an operating shaft shall apply to any other actuating device; ~ the angular rotation shall be taken to mean mechanical travel of the actuating device; ~ a value for force shall be prescribed instead of a value for torque if the actuating device moves in a linear instead of a rotary manner. These alternative prescriptions will be found in the sectional or detail specification. When a component is constructed as a variable resistor, i.e. as a two-terminal device, the detail specification shall prescribe the modifications required in the standard tests.

Potentiometers for use in electronic equipment - Part 1: Generic specification

KS C IEC 60393-5-2:2005 电子设备用电位器.第5-2部分:空白详细规范:单圈旋转低功率电位器.评定水平F

서 문 이 규격은 1992년 제1판으로 발행된 IEC 60393-5-2 Potenti

Potentiometers for use in electronic equipment-Potentiometers for use in electronic equipment-low-power potentiometer-Assessment level F

KS C IEC 60393-5:2005 电子设备用电位器.第5部分:分规范:单圈旋转线绕和非线绕低功率电位器

이 규격은 정격 전력이 10 W 이하인 단일 회전 저전력 권선형 및 비권선형 퍼텐쇼미터에

Potentiometers for use in electronic equipment－Part 5：Sectional specification：Single-turn rotary low-power wirewound and non-wirewound potentiometers

KS C IEC 60393-5-1:2005 电子设备用电位器.第5-1部分:空白详细规范:单圈旋转低功率电位器.评定水平E

서 문 이 규격은 1992년 제1판으로 발행된 IEC 60393-5-1 Potenti

Potentiometers for use in electronic equipment-Part 5:Blank detail specification:Single-turn rotary low-power potentiometers, Assessment level E

KS C IEC 60393-1:2004 电子设备用电位器.第1部分:通用规范

이 규격은 전자 기기에 사용되는 나사 조정형, 반고정형, 복수 턴 유닛 등 모든 종류의

Potentiometers for use in electronic equipment－Part 1：Generic specification

KS C IEC 60393-2-1:2004 电子设备用电位器.第2部分:空白详细规范.第1节:螺杆驱动和旋转预调电位器.E级评定

서 문 이 규격은 1989년에 제1판으로 발행된 IEC 60393-2-1 Pote

Potentiometers for use in electronic equipment-Part 2:Blank detail specification-Lead-screw actuated and rotary preset potentiometers, Assessment level E

KS C IEC 60393-2:2004 电子设备用电位器.第2部分:分规范:螺杆驱动和旋转预调电位器

이 규격은 전자 기기용 권선형 및 비권선형 나사 조정형 반고정 퍼텐쇼미터와 권선형 및

Potentiometers for use in electronic equipment－Part 2：Sectional specification－Lead－screw actuated and rotary preset potentiometers

KS C IEC 60393-2-2:2004 电子设备用电位器.第2部分:空白详细规范.第2节:丝杆驱动和旋转预调电位器.F级评定

서 문 이 규격은 1992년에 제1판으로 발행된 IEC 60393-2-2 Pote

Potentiometers for use in electronic equipment-Part 2:Blank detail specification-Lead-screw actuated and rotary preset potentiometers, Assessment level F

KS C IEC 60393-2-101:2004 电子设备用电位器.第2部分:详细规范.螺杆操纵的预置电位器.稳定级5%.评定级E

서 문 이 규격은 1994년에 제1판으로 발행된 IEC 60393-2-101 Po

Potentiometers for use in electronic equipment-Part 2:Detail specification-Lead-screw actuated preset potentiometers-Stability class 5 %-Assessment level E

DLA DSCC-DWG-92021 REV B-2004 变量表面安装4毫米1/4瓦特多圈电位器

This drawing describes the requirements for a variable, surface mount, non-wire wound resistor.

RESISTOR, VARIABLE, SURFACE MOUNT, 4MM, MULTITURN TRIMMER, 1/4 WATT

ISO/IEC 19757-2:2003 信息技术.文献模式定义语言.第2部分:基于语法规则的正确性检验.RELAX NG

This part of ISO/IEC 19757 specifies RELAX NG, a schema language for XML. A RELAX NG schema specifies a pattern for the structure and content of an XML document. The pattern is specified by using a regular tree grammar. This part of ISO/IEC 19757 establishes requirements for RELAX NG schemas and specifies when an XML document matches the pattern specified by a RELAX NG schema.

Information technology - Document Schema Definition Language (DSDL) - Part 2: Regular-grammar-based validation - RELAX NG

IEC 60393-6-1:2003 电子设备用电位器.第6-1部分:空白详细规范:表面安装预调电位器

A Blank Detail Specification is a supplementary document to the Sectional Specification and contains requirements for style, layout and minimum content of Detail Specifications.

Potentiometers for use in electronic equipment - Part 6-1: Blank detail specification: Surface mount preset potentiometers; Assessment level E

IEC 60393-6:2003 电子设备用电位器.第6部分:分规范:表面安装预调电位器

Prescribes preferred ratings and characteristics and selects appropriate quality assessment procedures, tests and measuring methods from IEC 60393-1 and gives general performance requirements for this type of potentiometer.

Potentiometers for use in electronic equipment - Part 6: Sectional specification: Surface mount preset potentiometers

DLA DSCC-DWG-97012 REV A-2003 变量非线绕电位器3/4瓦绕行引线电阻器

This drawing describes the requirements for a 3/4 watt trimmer, nonwire wound, variable resistor with flexible leads.

RESISTORS, VARIABLE, NONWIRE WOUND, TRIMMER, 3/4 WATTS, FLEXIBLE LEADS

SJ 50918/4-2002 WJ13型.螺杆驱动非线绕预调电位器详细规范

Potentiometers,preset,non-wirewound,lead-screw actuated,style WJ13,detail specification for