共找到 482 条与 系统设备接口 相关的标准,共 33 页
Signaling method for a bidirectional parallel peripheral interface for Personal Computers
Information systems - Small computer system interface-2
Information technology - Portable Operating System Interface (POSIX)- Part 2: Shell and Utilities Volume 2
Information technology - Portable Operating System Interface (POSIX)- Part 2: Shell and Utilities Volume 1
To define and interface standard for very high Performance multiprocessor systems that supports a coherent shared-memory model scalable to systems with up to 64 K nodes.
Standard for Scalable Coherent Interface (SCI) (IEEE Computer Society Document)
The scope of this Standard is t h e definition of the response of a of the%XeThis standard addreasee the control of machines capable of performing 2 , 3, 4, and 5 axis motion of an active tool ( m I l l , laser, pen, etc.) r e l a t I v e t o a part,
32 Bit Binary CL (BCL) and 7 Bit ASCII CL (ACL) Exchange Input Format for Numerically Controlled Machines
Adopts the international CCITT X.32 standard, modifications and extensions to apply to DTE/DCE interfaces.
Information Systems - Interface between Data Terminal Equipment (DTE) and Data Circuit-Terminating Equipment (DCE) for Terminals Operating in the Packet Mode and Accessing a Packet-Switched Public Data Network Through Switched Access Replaces ANSI X3.187
The Chip Carrier Sockets of assessed quality covered by this detail specification shall have
Detail Specification for Chip Carrier (PCC) Family 1.27 mm (.050 Inch) Leadspacing
Describes the Logical Level 2 (device level) Interface for disk drives, the physical, electrical and configuration characteristics of which are in accordance with ISO/IEC 9318-1. Is to facilitate the development and utilization of a device level interface which permits the interconnection of disk slave peripherals to a controller. Complements other Intelligent Peripheral Interface standards.
Information Technology - Intelligent Peripheral Interface Part 2: Device Specific Command Set for Magnetic Disk Drives (First Edition)
Information technology; intelligent peripheral interface; part 4: device generic command set for magnetic tape drives
Describes the Logical Level 3 (generic level) Interface for magnetic and optical disk drives, the physical, electrical and configuration characteristics of which are in accordance with ISO/IEC 9318-1. Is to facilitate the development and utilization of an intelligent interface which permits the interconnection of multiple peripheral types such as disk, tape, communications, to a controller. Complements other Intelligent Peripheral Interface standards.
Information Technology - Intelligent Peripheral Interface Part 3: Device Generic Command Set for Magnetic and Optical Disk Drives (First Edition)
Information processing systems, small computer systems interface (SCSI) (ISO 9316, 1st edition 1989)
The standard size, one pole watertight toggle switches of certified quality covered by this detail specification
Detail Specification on 1 Pole Toggle Switches
The standard size, four pole watertight toggle switches of certified quality covered by this detail specification
Detail Specification on 4 Pole Toggle Switches
The standard size, two pole watertight toggle switches of certified quality covered by this detail specification a) mount in a 12.4 mm ( . 4 9 inch) diameter mounting hole.
Detail Specification on 2 Pole Toggle Switches
Interface between flexible disk cartridge drives and their host controllers
in most cases, the interface between humans and machines is a visual display. The sharpness and readability of raster-scanned Cathode-Ray Tube (CRT) displays conventionally has been determined by how far the vemcal raster height could be reduced while
MTF Test Method for Monochrome CRT Display Systems
This Standard defines a machine coordinate system and machine motion nomenclature for numerically controlled machines.
Axis and Motion Nomenclature for Numerically Controlled Machines
Information processing systems; small computer system interface (SCSI)
Type FD plugs when mated with Type FD jacks must meet the ratings and characteristics. Type FD jacks, once mated with non-Type FD connectors (e.g., Type F connectors), may not meet the ratings and characteristics for type FD connectors.
75 Ohm Type FD Connector Interfaces, Rating, and Characteristics
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号