N73 机械振动、冲击设备与动平衡机 标准查询与下载

EN 30326-1:1994/A2:2011 机械振动.评估车辆座椅振动的实验室的方法.第1部分:基本要求.修订2（ISO 10326-1:1992 / AMD 2:2011）

Mechanical vibration - Laboratory method for evaluating vehicle seat vibration - Part 1: Basic requirements - Amendment 2 (ISO 10326-1:1992/Amd 2:2011)

SAE J577-2011 振动测试机及操作程序

Vibration Test Machine

Vibration Test Machine

ASTM E2425-11 动态机械分析仪损耗模量一致性的标准试验方法

This test method demonstrates conformity of a dynamic mechanical analyzer at an isothermal temperature of 21 °C. Dynamic mechanical analysis experiments often use linear temperature change. This test method does not address the effect of that change in temperature on the loss modulus. This test method may be used in research and development, specification acceptance, and quality control or assurance.1.1 This test method describes the performance confirmation or measurement of conformance for the loss modulus scale of a commercial or custom-built dynamic mechanical analyzer (DMA) at 21 °C using ultra-high molecular weight polyethylene as a reference material. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 There is no ISO standard equivalent to this test method. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Standard Test Method for Loss Modulus Conformance of Dynamic Mechanical Analyzers

JJG 1062-2010 便携式振动校准器检定规程

本规程适用于便携式振动校准器（以下简称振动校准器）的首次检定、后续检定和使用中检验。

Verification Regulation of Portable Vibration Calibrator

JJG 1063-2010 电液伺服万能试验机检定规程

本规程适用于最大试验力不大于3MN的电液伺服万能试验机（以下简称试验机）的首次检定、后续检定和使用中检验。电液伺服压力试验机也可参照执行。

Verification Regulation of Electro-hydraulic Servo Universal Testing Mechines

JB/T 6867-2010 陀螺转子平衡机 技术条件

本标准规定了陀螺转子平衡机的术语和定义与符号、基本参数、技术要求、检验方法、检验规则、标志、包装、运输和贮存等内容。 本标准适用于自驱动陀螺转子平衡机。

Specification for gyrorotor balancing machines

SANS 16063-31:2009 振动和冲击传感器的校正方法．第31部分：横向振动灵敏度测试

Specifies details of the instrumentation and methods to be used for transverse vibration sensitivity testing. Applies to rectilinear velocity and acceleration transducers.

Methods for the calibration of vibration and shock transducers Part 31: Testing of transverse vibration sensitivity

ISO 20806:2009 机械振动.中型和大型转子的现场平衡标准和保护装置

Mechanical vibration - Criteria and safeguards for the in-situ balancing of medium and large rotors

JG/T 245-2009 混凝土试验用振动台

本标准规定了试验室用混凝土试验用振动台(以下简称振动台)的分类与标记,组成与使用条件,要求,检验方法,检验规则,标志、包装、运输和贮存等。 本标准适用于振动台的设计、生产和质量检验。

Vibrating table for concrete test

EN 1299:1997+A1:2008 机械振动和冲击.机械隔振.源隔离应用的信息

This European Standard gives guidelines to ensure that manufacturers of machines provide adequate information on application of vibration isolation to reduce the risks arising from vibration generated by their machines. Guidelines are also provided to ensure that users furnish sufficient information regarding their applications to suppliers of machines or, where applicable, to the supplier of the isolation system, to enable the optimum selection and design of vibration isolation. This European Standard is restricted to source isolation. Although this standard is primarily intended for the use of new machines, it may be applied to the installation of used machines, too. This European Standard is addressed to manufacturers and installers of a machine, as a guide to define relevant parameters for the choice and installation of a vibration isolation system to be used with the machine. NOTE This European Standard may also be applied by users of machines already installed, who use or wish to use vibration isolation to solve a vibration problem caused by the machine. This European Standard shall not be considered as a manual for the design or installation of an isolation system. Examples of elements of vibration isolation are shown in Annex A only for information.

Mechanical vibration and shock - Vibration isolation of machines - Information for the application of source isolation

JJF 1192-2008 汽车悬架装置检测台校准规范

本规范适用于谐振式汽车悬架装置检测台（以下简称检测台）的校准。

Calibration Specification for Automotive Suspension Tester

SANS 16063-22:2008 对振动及冲击传感器的校准方法.第22部分:与基准传感器进行比对的冲击校准

Specifies the instrumentation and procedures to be used for secondary shock calibration of rectilinear transducers, using a reference acceleration, velocity or force measurement for the time-dependent shock. The methods are applicable in a shock pulse du

Methods for the calibration of vibration and shock transducers Part 22: Shock calibration by comparison to a reference transducer

SANS 16063-13:2008 对振动及冲击传感器的校准方法.第13部分:采用激光干涉法一次冲击校准

Specifies the instrumentation and procedure to be used for primary shock calibration of rectilinear accelerometers, using laser interferometry to sense the time-dependent displacement during the shock. The method is applicable in a shock pulse duration r

Methods for the calibration of vibration and shock transducers Part 13: Primary shock calibration using laser interferometry

JB/T 6869-2008 水平振动台（正弦） 技术条件

本标准规定了水平振动台（联用水平滑台的电动振动台或液压振动台）的基本参数、技术要求、检验方法和检验规则等。 本标准适用于正弦振动试验用水平振动台。其联用的水平滑台限于采用油膜或静压支承原理设计制造的、且配用单个振动台的滑台。

Specifications for the horizontal vibration generator systems (sinusoidal)

JB/T 6868-2008 冲击台 技术条件

本标准规定了冲击台的基本参数、技术要求、检验方法和检验规则等。 本标准适用于负载不大于3000kg的冲击台。

Specifications for the shock testing machines

BS ISO 8568:2008 机械冲击.测试机.特征和性能

This International Standard specifies performance parameters and methods of inspection of mechanical shock-testing machines and gives guidelines for describing their characteristics. It is intended to ensure that the potential user of a particular shock-testing machine is provided with an adequate description of the characteristics of the machine, and also to give guidance on the selection of such machines. This International Standard is applicable to the shock-testing machines that are used for demonstrating or evaluating the effect of shock conditions representative of the service environment in accordance with the relevant part of IEC 60068 and also for diagnostic testing. The purpose of the shock test is to reveal mechanical weakness and/or degradation in specified performance. It can also be used to determine the structural integrity of a test specimen or as a means of quality control. Machines used for simulation of earthquakes, sonic booms, explosions and implosions, bursting tests, metalworking, forming, etc. are not covered in this International Standard. Several techniques for generating the desired shock motion are discussed. Both simple-pulse and complex transients can be produced. The simulation of transients can be achieved by control of the test with a specified shock-response spectrum. NOTE 1 Annex A gives a description of pulse-shaping devices. Annex B defines methods of application of the shock response spectra. Annex C considers a method of evaluating the possibility of using a vibration generator for producing a shock pulse. Annexes D and E deal with the methods of measurement of some characteristics in inspection methods (or procedures) of shock-testing machines. NOTE 2 Characteristics of vibration-generating equipment are covered in ISO 5344, ISO 6070 and ISO 8626.

Mechanical shock. Testing machines. Characteristics and performance

SANS 16063-1:2008 振动与冲击传感器的校准方法.第1部分:基本概念

Describes methods for the calibration of vibration and shock transducers. It also includes methods for the measurement of characteristics in addition to the sensitivity.

Methods for the calibration of vibration and shock transducers Part 1: Basic concepts

SANS 16063-11:2008 振动与冲击传感器的校准方法.第11部分:激光干涉法作主要的振动校准

Specifies the instrumentation and procedure to be used for primary vibration calibration of rectilinear accelerometers (with or without amplifier) to obtain magnitude and phase lag of the complex sensitivity by steady-state sinusoidal vibration and laser interferometry.

Methods for the calibration of vibration and shock transducers Part 11: Primary vibration calibration by laser interferometry

SANS 16063-21:2008 振动和冲击传感器的校准方法.第21部分:与标准传感器比对进行振动校准

Describes the calibration of rectilinear vibration transducers by comparison. Although it mainly describes calibration using direct comparison to a standard calibrated by primary methods, the methods described can be applied between other levels in the calibration hierarchy.

Methods for the calibration of vibration and shock transducers Part 21: Vibration calibration by comparison to a reference transducer

EN 14253:2003+A1:2007 机械振动.职业接触全身振动对健康影响的测量和计算.实践指导

This European Standard provides guidelines for the measurement and evaluation of whole-body vibration at the workplace. This European Standard describes the precautions to be taken to make representative vibration measurements and to determine the daily exposure time for each operation in order to calculate the daily exposure value standardized to an 8 h reference period. This European Standard provides a means to determine the relevant operations that should be taken into account when determining the vibration exposure. This European Standard applies to situations where people are exposed to whole-body vibration at the workplace, transmitted through the buttocks for a seated person or through the feet for a standing person. This European Standard is restricted to the evaluation of exposure to whole-body vibration using quantities derived from frequency-weighted root-mean-square acceleration. The frequency range considered is 0,5 Hz to 80 Hz. Where the vibration includes shocks or impacts, methods in this European Standard may underestimate the severity of the exposure. There is a need to assess the risks arising from exposure to whole-body shocks and high crest factor vibration. Methods for this are beyond the scope of this European Standard.

Mechanical vibration - Measurement and calculation of occupational exposure to whole-body vibration with reference to health - Practical guidance