共找到 501 条与 金属结构工程 相关的标准,共 34 页
本规程适用于山东省行政区域内的结构中混凝土强度现场检测,检测混凝土强度范围(10.0-80.0)MPa,不适用于纤维混凝土或轻骨料混凝土的强度检测。
Technical specification for testing concrete compressive strength by tensile stress method
Technical specifications for anti-corrosion coating of steel structures for civil air defense engineering protective equipment
本标准规定了大直径缓粘结预应力钢绞线的术语和定义、代号和标记、要求、试验方法、检验规则、包装、标志、贮存和使用等。
Large diameter slow bonded prestressed steel strand
Technical specification for steel structure houses
Technical specification for damage assessment of steel structures after fire
Specifications for Design of Hoists in Hydropower Projects Part 3: Design Specifications for Screw Type Hoists
本规程适用于工业与民用建筑及构筑物中采用的钢筋桁架楼承板系统的设计、施工和验收。
Technical specification for the application of reinforced truss floor deck system
Technical specification for construction of composite aluminum alloy formwork for construction engineering
According to EN 1993-4-2 certain parameters may be defined by the national CEN member bodies. This national annex contains specific parameters which apply for Germany.
National Annex - Nationally determined parameters - Eurocode 3: Design of steel structures - Part 4-2: Tanks
According to EN 1993-1-1 certain parameters may be defined by the national CEN-member bodys. This national annex contains specific parameters which apply for Germany.
National Annex - Nationally determined parameters - Eurocode 3: Design of steel structures - Part 1-1: General rules and rules for buildings
According to EN 1993-1-5 certain parameters may be defined by the national CEN-member bodys. This national annex contains specific parameters which apply for Germany.
National Annex - Nationally determined parameters - Eurocode 3: Design of steel structures - Part 1-5: Plated structural elements
According to EN 1993-4-1 certain parameters may be defined by the national CEN-member bodys. This national annex contains specific parameters which apply for Germany.
National Annex - Nationally determined parameters - Eurocode 3: Design of steel structures - Part 4-1: Silos
According to EN 1993-1-6 certain parameters may be defined by the national CEN-member bodys. This national annex contains specific parameters which apply for Germany.
National Annex - Nationally determined parameters - Eurocode 3: Design of steel structures - Part 1-6: Strength and stability of shell structures
This European Standard specifies requirements for execution of structural steelwork as structures or as manufactured components, produced from hot rolled, structural steel products up to and including grade S690; cold formed components and sheeting up to and including grades S700; hot finished and cold formed austenitic, austenitic-ferritic and ferritic stainless steel products; hot finished and cold formed structural hollow sections, including standard range and custom-made rolled products and hollow sections manufactured by welding.
Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures; German version EN 1090-2:2018
This National Annex contains the specific parameter for the use of DIN EN 1999-1-1 in Germany as well as references to additional non-conflicting national rules for the design according to DIN EN 1999-1-1.
National Annex - Nationally determined parameters - Eurocode 9: Design of aluminium structures - Part 1-1: General rules
Hydropower Engineering Unit Engineering Quality Grade Assessment Standards Part 2: Metal Structure and Hoist Installation Engineering
According to EN 1993-6 certain parameters may be defined by the national CEN-member bodys. This national annex contains specific parameters which apply for Germany.
National Annex - Nationally determined parameters - Eurocode 3: Design of steel structures - Part 6: Crane supporting structures
This National Annex contains the specific parameter for the use of DIN EN 1999-1-1 in Germany as well as references to additional non-conflicting national rules for the design according to DIN EN 1999-1-1.
National Annex - Nationally determined parameters - Eurocode 9: Design of aluminium structures - Part 1-1: General rules, Amendment A1
According to EN 1993-1-1 certain parameters may be defined by the national CEN-member bodys. This national annex contents specific parameters which apply for Germany.
National Annex - Nationally determined parameters - Eurocode 3: Design of steel structures - Part 1-1: General rules and rules for buildings
(1) Part 4-2 of Eurocode 3 provides principles and application rules for the structural design of vertical cylindrical, conical and pedestal above ground steel tanks for the storage of liquid products with the following characteristics: a) tanks with capacity greater than 100 m3 (100000 l); b) tanks that have significant fabrication or assembly on site; c) shop-fabricated tanks with conical bottoms, supported on skirts or columns; d) tanks with characteristic internal pressures above the liquid surface not more negative than -0,1 bar and not greater than 0,5 bar; e) design metal temperatures limited to the ranges: 1) tanks constructed using structural steel grades, -50 °C >T < +300 °C; 2) tanks constructed using austenitic stainless steels, -165 °C > T < +300 °C; 3) tanks constructed with special steel grades that have defined yield strengths up to higher temperatures, -165 °C > T < the maximum defined temperature for the grade; 4) tanks susceptible to failure by fatigue, T < 150 °C; f) in cylindrical ground-supported tanks, the maximum design liquid level not higher than the top of the cylindrical shell. (2) This Part 4-2 is concerned only with the requirements for resistance and stability of steel tanks. Other design requirements are covered by EN 14015 for ambient temperature tanks and by EN 14620 for cryogenic tanks, and by EN 1090 for fabrication and erection considerations. These other requirements include foundations and settlement, fabrication, erection and testing, functional performance, and details like man-holes, flanges, and filling devices. (3) Provisions concerning the special requirements of seismic design are provided in EN 1998-4 (Eurocode 8 Part 4 Design of structures for earthquake resistance: Silos, tanks and pipelines), which complements the provisions of Eurocode 3 specifically for this purpose. (4) The design of a supporting structure for a tank is dealt with in EN 1993-1-1. (5) The design of an aluminium roof structure on a steel tank is dea
Eurocode 3: Design of steel structures - Part 4-2: Tanks; German version EN 1993-4-2:2007 + AC:2009 + A1:2017
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号