Q22 建筑用塑料制品 标准查询与下载

ASTM C578-10 硬质蜂窝状聚苯乙烯热绝缘板标准规范

1.1 This specification covers the types, physical properties, and dimensions of cellular polystyrene boards with or without facings or coatings made by molding (EPS) or extrusion (XPS) of expandable polystyrene. Products manufactured to this specification are intended for use as thermal insulation for temperatures from -65 to +165°F (-53.9 to +73.9°C). This specification does not apply to laminated products manufactured with any type of rigid board facer including fiberboard, perlite board, gypsum board, or oriented strand board. 1.1.1 For Type XIII only, this specification covers the physical properties, and dimensions of cellular polystyrene intended for use as thermal insulation for temperatures from −297 to +165°F (−183 to +73.9°C). 1.2 Consult the manufacturer for specific recommendations and properties in cryogenic conditions. 1.2.1 This specification does not cover cryogenic properties except for the k-factors for Type XIII in Appendix X1. For Type XIII in specific cryogenic applications, the manufacturer and purchaser shall agree upon the actual temperature limits and physical property requirements in addition to the k-factors in Appendix X1. 1.3 The use of thermal insulation materials covered by this specification may be regulated by building codes that address fire performance. For some end uses, specifiers should also address the effect of moisture. Guidelines regarding these end use considerations are included in Appendix X1. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation

ASTM D4226-10 刚性聚(氯乙烯)建筑产品的耐撞击性能的标准试验方法

The impact strength values obtained on the flat sections of a building product profile are relevant only to the flat section that has been tested and these values do not necessarily indicate the impact resistance of the whole product, which is affected by the configuration of the profile (that is, corners, ribs, etc). Constant weight and variable height, employed in these test methods, allow the velocity of impact to vary and, therefore, by Procedure B, can determine the energy of ductile-to-brittle transition, which cannot be determined if a variable weight is dropped from a constant height. These test procedures have been found to be useful elements in rigid poly(vinyl chloride) (PVC) building product characterization. Compound qualification, finished product quality control, environmental and weatherability research and development studies, and fabrication tolerance prediction constitute useful applications. Choice of the specific impactor head configuration used is related to a variety of product attributes, such as specimen thickness and product toughness as well as abstract factors, such as the anticipated mode of failure in a specific application. The geometric uniqueness of the impactor head configurations prevents any comparison or correlation of testing results on samples tested with differing impactor head configurations. In general, the conical impactor, C.125, is useful to ensure failure of thicker specimens where the H.25 impactor caused no failure. Note 28212;Equivalent surface conditions are more likely to occur when specimens are prepared by compression molding or extrusion than by injection molding. When comparing different samples tested with the same impactor head configuration, impact resistance shall be permitted to be normalized for average specimen thickness over a reasonably broad range (for example, 1 to 3 mm). However, this should only be done when the surface conditions listed in 6.1 are essentially equivalent.1.1 These test methods cover the determination of the energy required to crack or break rigid poly(vinyl chloride) (PVC) plastic sheeting and profile flat sections used in building products, as well as extruded or molded test samples, under specified conditions of impact from a freefalling standard weight striking an impactor with either of two configurations in contact with the specimen. 1.2 Two test procedures are included: 1.2.1 Procedure A, used to determine minimum impact energy required to cause failure (hole, crack, split, shatter, or tear). 1.2.2 Procedure B, used to determine minimum impact energy required to cause brittle failure. 1.3 The values in inch-pound units are to be regarded as the standard. Note 18212;There is no similar or equivalent ISO standard. 1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding, those in tables in figures) shall not be considered as requirements of this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 8.

Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products

ASTM D4397-10 建筑、工业和农业用聚乙烯薄膜标准规范

1.1 This specification covers polyethylene sheeting, 250 μm (0.010 in. or 10 mils) or less in thickness, intended for construction, industrial, and agricultural applications. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 The following precautionary statement pertains only to the test methods portion, Section 8 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;There is no known ISO equivalent to this standard.

Standard Specification for Polyethylene Sheeting for Construction, Industrial, and Agricultural Applications

EN ISO/TS 15877-7:2009 冷热水装置用塑料管道系统.氯化聚(氯乙烯)(PVC-C).第7部分:合格评定指南

Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity

NY/T 1496.2-2007 农村户用沼气输气系统 第2部分：塑料管件

本部分规定了农村户用沼气输气系统聚乙烯(PE)、聚氯乙烯(PVC)塑料管件的技术要求、试验方法、检验规则、包装、标志、运输和贮存等。 本部分适用于在压力12 kPa和温度40℃以下环境条件中使用。

Biogas transmission system for rursl household.Part 2: Thermoplastics pipe fittings

NY/T 1496.3-2007 农村户用沼气输气系统 第3部分：塑料开关

本部分规定了农村户用沼气输气系统使用的塑料开关的技术要求、试验方法、检验规则、包装、标志、运输和贮存等。 本部分适用于农村户用沼气输气系统用聚乙烯(PE)和聚氯乙烯(PVC)材料制作的壳体。 本部分中聚乙烯(PE)材料和聚氯乙稀(PVC)材料制作的开关不适于在户外暴露状态下使用。

Biogas transmission system for rural household-Part 3:Thermoplastics valves

NY/T 1496.1-2007 农村户用沼气输气系统 第1部分：塑料管材

本部分规定了农村户用沼气输气系统聚乙烯(PE)、聚氯乙烯(PVC)管材和聚氯乙烯树脂为主要原料挤出成型软管的要求、试验方法、检验规则、包装、标志、运输和贮存等。 本部分适用于在压力12 kPa和温度40℃以下环境条件中使用。

Biogas transmission system for rural household-Part 1: Thermoplastics pipes

EN ISO 15876-2:2003/A1:2007 冷热水装置用塑料管道系统.聚丁烯(PB).第2部分:管材.修订1(ISO15876-2:2003/AMD1:2007)

Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 2: Pipes - Amendment 1 (ISO 15876-2:2003/Amd 1:2007)

EN ISO 15876-1:2003/A1:2007 冷热水装置用塑料管道系统.聚丁烯(PB).第1部分:总则.修改1(ISO 15876-1:2003/Amd 1:2007)

Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 1: General - Amendment 1 (ISO 15876-1:2003/Amd 1:2007)

DIN EN 15334:2007 卫生设备.高填料含量的甲基丙烯酸分解物

This European Standard specifies test methods for measuring characteristics of pure methacrylic dispersions and sanitary appliances produced from dispersions by polymerisation.

Sanitary appliances - Methacrylic dispersions of high filler content English version of DIN EN 15334:2007-05

KS F 2805-2004 混响室内部吸声性能测定方法

이 규격은 음향 재료의 흡음 계수 또는 가구, 사람, 흡음체 등 물체의 등가 흡음 면적

Measurement of sound absorption in a reverberation room

JC/T 941-2004 门、窗用玻璃纤维增强塑料拉挤中空型材

本标准规定了门、窗用玻璃纤维增强塑料拉挤中空型材的产品标记、技术要求、试验方法、检验规 则以及标志、包装、运输、贮存。 本标准适用于制做建筑门、窗用的玻璃纤维增强塑料拉挤中空型材 。

Pultruded glass fiber reinforced plastics hollow section for doors and windows

JC/T 939-2004 建筑用抗细菌塑料管抗细菌性能

Antibacterial property of antibacterial plastics pipes used for building

JC/T 937-2004 软式透水管

Flexible permeable hose

EN ISO/TS 15876-7:2003 冷热水装置用塑料管道系统.聚丁烯(PB).第7部分:合格评定指南

Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 7: Guidance for the assessment ofconformity

EN ISO/TS 15875-7:2003 冷热水装置用塑料管道系统.交联聚乙烯(PE-X).第7部分:合格评定指南

Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 7: Guidance for the assessment of conformity

EN ISO/TS 15874-7:2003 冷热水装置用塑料管道系统.聚丙烯(PP).第7部分:合格评定指南

Plastics piping systems for hot and cold water installations �C Polypropylene (PP) �C Part 7: Guidance for the assessment of conformity

NY/T 669-2003 建筑排水用再生塑料管材

本标准规定了以廢舊塑料为主料，加和必要的輔料，擠出成型的建築用再生塑料排水管材(以下筒 称管材)的产品分类、技术要求、试验方法.检验规则，标志、使用说明书.包装，贮存和运输。 本标准适用于民用建筑内排水用管材。

Regenerate plastics pipes for drainage in buildings

ASTM D4216-03 硬质聚氯乙烯(PVC)和相关聚氯乙烯(PVC)及氯化聚氯乙烯(CPVC)建筑制品化合物的标准规范

1.1 This specification covers rigid plastic PVC and CPVC Exterior compounds composed of poly(vinyl chloride), chlorinated poly(vinyl chloride), vinyl chloride copolymers or vinyl chloride blends, and the necessary compound ingredients intended for use in making building products. The compounding ingredients may consist of lubricants, stabilizers, nonpoly(vinyl chloride) resin modifiers, colorants or pigments, or both, and inorganic fillers.1.2 This specification is intended to provide classification of base compounds used to manufacture PVC and CPVC exterior building products. Physical properties may be determined by evaluating compounds of any color. Note 18212;Two year weathering studies, without specific requirements for color change and physical property change, are recommended for all colors of new compounds and compounds for new applications to provide the basis for agreement between producer and buyer on the suitability of the compound for the intended application. 1.3 The requirements in this specification are intended for qualification, as well as for quality control of compounds used to manufacture building products. They are not applicable to finished building products. See Specifications D 3679 D 4477, D 4726, and F 964 for requirements for finished products. 1.4 It may be necessary, in special cases, to select specific compounds for unusual applications that require consideration of other properties not covered in this specification. 1.5 The rate of burning test, Test Method D 635, is used in this specification only as a screening test for identification of certain properties of the PVC compound; there is no flammability test or flammability requirement for the compound. 1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.7 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 28212;There are no ISO standards covering the primary subject matter of this specification. 1.8 The text of this standard references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard. 1.9 Rigid PVC recycle plastic meeting the requirements of this specification may be usable in some applications. Refer to the specific requirements in the Materials and Manufacture Section of the applicable product standard.

Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) and Related PVC and Chlorinated Poly (Vinyl Chloride) (CPVC) Building Products Compounds

KS B 7069-2002 塑料电缆管

이 규격을 일정 거리를 왕복 운동하는 장치에 전기 배선 및 호스가 굴절되거나 습기, 진동,

Plastic cable duct