Q33 建筑玻璃 标准查询与下载

JC/T 2167-2013 玻璃釉料

本标准规定了玻璃釉料的术语和定义、分类、要求、试验方法、检验规则以及标志、包装、运输和贮存等。本标准适用于建筑玻璃及工业玻璃用玻璃釉料。本标准不适用于汽车玻璃用玻璃釉料。

Glass enamel

NF P78-102-2*NF EN 572-2:2013 建筑用玻璃. 基本钠钙硅酸盐玻璃制品. 第2部分: 浮法玻璃

Glass in building - Basic soda lime silicate glass products - Part 2: float glass

NF P78-102-4*NF EN 572-4:2013 建筑用玻璃. 基本钠钙硅酸盐玻璃制品. 第2部分: 拉制平板玻璃

Glass in building - Basic soda lime silicate glass products - Part 2: drawn sheet glass

NF P78-102-8:2013 建筑用玻璃 - 基本钠钙硅酸盐玻璃制品 - 第8部分: 供货和最终切割尺寸

Glass in building - Basic soda lime silicate glass products - Part 8: supplied and final cut sizes

NF P78-102-1:2013 建筑用玻璃.基本的碱石灰硅酸盐玻璃制品.第1部分:定义和通用物理及机械性能

Glass in building - Basic soda lime silicate glass products - Part 1: definitions and general physical and mechanical properties

DB52/T 790-2013 建筑门窗用贴膜中空玻璃

Film insulating glass for building doors and windows

ANSI A137.2-2013 玻璃瓷砖国家规范

National Specifications for Glass Tile

EN 15683-2:2013 建筑玻璃 热钢化钠钙硅酸盐槽形安全玻璃 第2部分：合格评定/产品标准

This European Standard covers the evaluation of conformity and the factory production control of thermally toughened soda lime silicate channel shaped safety glass for use in buildings. This also includes requirements subject to regulation.

Glass in building - Thermally toughened soda lime silicate channel shaped safety glass - Part 2: Evaluation of conformity/Product standard

ASTM C212-13 建筑用饰面瓷砖的标准规格

1.1 This specification covers structural clay load-bearing facing tile. Structural facing tile are tile designed for use in interior and exterior unplastered walls and partitions of buildings. 1.2 The property requirements of this specification apply at the time of purchase. The use of results from testing of tile extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 5) of this standard is beyond the scope of this specification. 1.3 Tile covered by this specification are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength and durability requirements of this specification. (See firing and fired bond in Terminology C1232.) 1.4 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Structural Clay Facing Tile

ASTM F3006-13 层压建筑用平板玻璃的落球冲击阻力的标准规范

1.1 This specification covers the destructive ball drop testing of laminated flat glass products intended for use in architectural glazing applications. 1.2 This specification is intended for use as an in-plant quality control test to evaluate the impact performance of laminated flat glass when a 2.3 kg, 83 mm diameter smooth solid steel ball is dropped from a specified height. 1.3 This specification does not yield data that is a substitute for safety glazing test requirements of ANSI Z97.1 or CPSC 16 CFR 1201. Qualification under this specification provides a basis for judgment of the ability of specimens to withstand the appropriate shot-bag impact. This specification provides a mechanism to allow fabricators a less cumbersome and lower cost method for the evaluation of impact performance that may be performed on a frequent basis while reducing the amount of waste materials generated from traditional impact tests. 1.4 This specification is applicable to symmetrical and asymmetrical annealed, heat-strengthened, chemically strengthened, fully tempered laminated architectural flat glass including but not limited to: float, patterned, sheet, sand-blasted, grooved, and fritted. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 4 on Hazards.

Standard Specification for Ball Drop Impact Resistance of Laminated Architectural Flat Glazing

ASTM F3007-13 层压建筑用平板玻璃的落球冲击阻力的标准试验方法

5.1 The impact performance of laminated glass varies with the glass ply thickness, type, and kind as well as the thickness and type of interlayer used in the overall configuration. 5.2 Specific safety properties are required for laminated glass to meet the safety glazing requirements of ANSI Z97.1 and CPSC 16 CFR 1201. Compliance with the minimum quality requirements of Specification C1172 does not constitute compliance or assure compliance with the referenced safety glazing standards. 5.3 While this test method does not replace the test requirements of ANSI Z97.1 or CPSC 16 CFR 1201 safety glazing standards addressed above, destructive ball drop impact testing does provide a method of expeditious in-plant evaluation of laminated glass products being fabricated. 5.4 Impact procedures for testing in accordance with safety glazing standards ANSI Z97.1 and CPSC 16 CFR 1201 differ from this ball drop test method; however, the penetration resistance of a single laminated lite can be determined and used for quality control purposes. 1.1 This test method covers the destructive ball drop testing of laminated flat glass products intended for use in architectural glazing applications. 1.2 This test method is intended for use as an in-plant quality control test to evaluate the impact performance of laminated flat glass when a 2.3 kg, 83 mm diameter smooth solid steel ball is dropped from a user selected height. 1.3 This test method is not a substitute for safety glazing test requirements of ANSI Z97.1 or CPSC 16 CFR 1201. 1.4 This test method is applicable to symmetrical and asymmetrical annealed, heat-strengthened, chemically strengthened, fully tempered laminated architectural flat glass including but not limited to: float, patterned, sheet, sand-blasted, grooved, and fritted. 1.5 The values stated in SI units are to be regarded as standard. No other units of measure are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 7 on Hazards.

Standard Test Method for Ball Drop Impact Resistance of Laminated Architectural Flat Glass

BS ISO 11485-2:2012 建筑玻璃.曲面玻璃.质量要求

Glass in building. Curved glass. Quality requirements

JC/T 2128-2012 超白浮法玻璃

本标准规定了超白浮法玻璃的术语和定义、分类、要求、检验方法、检验规则以及标志、包装、运输和贮存等。 本标准适用于建筑、家电、灯饰、交通、家具、太阳能等方面使用的超白浮法玻璃。

Ultra-clear float glass

KS L 2012-2012 浮法玻璃和抛光平板玻璃

이 표준은 주로 건축물, 차량의 창, 거울 등에 사용하는 플로트 판유리1) 및 마판유리2)

Float and polished plate glass

KS L 2016-2012 玻璃窗胶膜

이 표준은 사무실, 점포, 주택 등(이하 건축물이라 한다.)의 창 유리에 붙여 옥내의 냉방

Adhesive films for glazings

DIN EN 572-7:2012 建筑用玻璃.基本钠钙硅酸盐玻璃制品.第7部分:嵌丝或不嵌丝的槽形玻璃.德文版本EN 572-7-2012

Glass in building - Basic soda lime silicate glass products - Part 7: Wired or unwired channel shaped glass; German version EN 572-7:2012

DIN EN 572-4:2012 建筑用玻璃.基本钠钙玻璃制品.第4部分:拉制平板玻璃.德文版本EN 572-4-2012

Glass in building - Basic soda lime silicate glass products - Part 4: Drawn sheet glass; German version EN 572-4:2012

DIN EN 572-2:2012 建筑用玻璃. 基本钠钙硅酸盐玻璃制品. 第2部分: 浮法玻璃; 德文版本EN 572-2-2012

Glass in building - Basic soda lime silicate glass products - Part 2: Float glass; German version EN 572-2:2012

DIN EN 572-3:2012 建筑用玻璃.基本钠钙硅酸盐玻璃制品.第3部分:抛光嵌丝玻璃.德文版本EN 572-3-2012

Glass in building - Basic soda lime silicate glass products - Part 3: Polished wired glass; German version EN 572-3:2012

DIN EN 572-8:2012 建筑用玻璃.基本钠钙硅酸盐玻璃产品.第8部分:供货和最终切割尺寸.德文版本EN 572-8-2012

Glass in building - Basic soda lime silicate glass products - Part 8: Supplied and final cut sizes; German version EN 572-8:2012