Q34 工业技术玻璃 标准查询与下载
共找到 234 条与 工业技术玻璃 相关的标准，共 16 页
1.1 This specification covers chemical resistant, low expansion, Type I, borosilicate glass, Class A (see Specification E438), used to manufacture corrosion-resistant pipe and fittings for drain, waste, and vent service. 1.2 The pipe and fittings covered by the specification are intended for chemical resistant service above and below grade under gravity flow or vacuum conditions. 1.3 The pipe and fittings shall have beaded or plain ends.
Standard Specification for Borosilicate Glass Pipe and Fittings for Drain, Waste, and Vent (DWV) Applications
- ICS
- 23.040.50 (Pipes and fittings of other materials)
- CCS
- Q34
- 发布
- 2000
- 实施
1.1 This specification covers chemically resistant, low expansion, Type I, borosilicate glass, Class A (see Specification E438), used to manufacture corrosion-resistant pipe and fittings for drain, waste, and vent service. 1.2 The pipe and fittings covered by the specification are intended for chemical resistant service above and below grade under gravity flow or vacuum conditions. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The pipe and fittings shall have beaded or plain ends.
Standard Specification for Borosilicate Glass Pipe and Fittings for Drain, Waste, and Vent (DWV) Applications
- ICS
- 23.040.50 (Pipes and fittings of other materials)
- CCS
- Q34
- 发布
- 2000
- 实施
This International Standard specifies a test method for determining the grindability of raw optical glass with diamond pellets, and defines a classification of optical glasses according to the grindability determined by this method.
Raw optical glass - Grindability with diamond pellets - Test method and classification
- ICS
- 37.020
- CCS
- Q34
- 发布
- 1999-12
- 实施
This International Standard specifies test methods for resistance to radiation, high temperature, humidity, fire and simulated weathering, relating to the safety requirements for all safety glazing materials in a road vehicle, whatever the type of glass or the material of which they are composed.
Road vehicles - Safety glazing materials - Test methods for resistance to radiation, high temperature, humidity, fire and simulated weathering
- ICS
- 43.040.65
- CCS
- Q34
- 发布
- 1999-07
- 实施
Specifies the requirements for baths for domestic purposes made from acrylic materials which ensure that the product, when installed in accordance with manufacturers' instructions, gives satisfactory performance.
Specification for finished baths for domestic purposes made of acrylic material
- ICS
- 91.140.70
- CCS
- Q34
- 发布
- 1999-05-28
- 实施
Pressure resistant oblong sight glasses of borosilicate glass without limitation in the range of low temperature
- ICS
- 71.120.10
- CCS
- Q34
- 发布
- 1999-05
- 实施
Road vehicles - Measurement of scattered light of safety glazing materials for vehicle glazing - Part 1: Annular diaphragm method
- ICS
- 43.040.65
- CCS
- Q34
- 发布
- 1998-12
- 实施
この規格は，建築物，冷凍・冷蔵ショーケースなどに使用する複層ガラスについて規定する。
Sealed insulating glass
- ICS
- 81.040.20;81.040.30
- CCS
- Q34
- 发布
- 1998-03-20
- 实施
4.1 The term “reference” as employed in this practice implies that either the glass or the metal of the reference glass-metal seal will be a “standard reference material” such as those supplied for other physical tests by the National Institute for Standards and Technology (NIST), or a secondary reference material whose sealing characteristics have been determined by seals to a standard reference material.4 Until standard reference materials for seals are established by the NIST, secondary reference materials may be agreed upon between manufacturer and purchaser. 1.1 This practice covers the preparation and testing of reference glass-metal butt seals of two general configurations: one applicable to determining stress in the glass and the other to determining the degree of mismatch of thermal expansion (or contraction). Tests are in accordance with Test Method F218 (Section 1.1). 1.2 This practice applies to all glass and metal (or alloy) combinations normally sealed together in the production of electronic components. It should not be attempted with glass-metal combinations having widely divergent thermal expansion (or contraction) properties.
Standard Practice for
- ICS
- 21.140 (Seals, glands)
- CCS
- Q34
- 发布
- 1998
- 实施
本标准规定了湿式水表用钢化表玻璃的规格、技术要求、试验方法和检验规则。 本标准适用于湿式水表用钢化表玻璃。
Tempered glass for wet water meter
- ICS
- 81.040
- CCS
- Q34
- 发布
- 1997-04-01
- 实施
- 1997-04-01
Advanced technical ceramics. Mechanical properties of ceramic composites at high temperature under inert atmosphere. Determination of shear strength by compression loading of notched specimens
- ICS
- 81.060.30
- CCS
- Q34
- 发布
- 1996-08-15
- 实施
- 1996-08-15
Advanced technical ceramics. Mechanical properties of ceramic composites at high temperature in air at atmospheric pressure. Determination of tensile properties
- ICS
- 81.060.30
- CCS
- Q34
- 发布
- 1996-08-15
- 实施
- 1996-08-15
Advanced technical ceramics. Mechanical properties of ceramic composites at high temperature under inert atmosphere. Determination of tensile properties
- ICS
- 81.060.30
- CCS
- Q34
- 发布
- 1996-08-15
- 实施
- 1996-08-15
American National Standard for Safety Glazing Materials for Glazing Motor Vehicles and Motor Vehicle Equipment Operating on Land Highways Safety Code
- ICS
- 43.040.60;81.040.30
- CCS
- Q34
- 发布
- 1996-02-01
- 实施
This document applies to oblong sight glasses of tempered soda-lime-glass.
Pressure resistant oblong sight glasses of soda-lime-glass without limitation in the range of low temperature
- ICS
- 71.120.10
- CCS
- Q34
- 发布
- 1996-02
- 实施
