T23 转向与操纵系统 标准查询与下载

SAE J1574-2-2012 方向控制研究用车辆和悬挂参数的测量.基本原理

This SAE Information Report presents the background and rationale for SAE J1574-1.

Measurement of Vehicle and Suspension Parameters for Directional Control Studies--Rationale

ISO 17288-1:2011 乘用车.自由控制性能.第1部分:转向释放开环试验方法

This part of ISO 17288 specifies an open-loop test method for determining the free control stability of a passenger car as defined in ISO 3833, by measurement of the transient behaviour following steering release, starting from a steady-state cornering status. NOTE The open-loop manoeuvre specified in this part of ISO 17288 is not representative of normal driving conditions, but is nonetheless useful for obtaining a measure of vehicle transient behaviour.

Passenger cars - Free-steer behaviour - Part 1: Steering-release open-loop test method

ISO 17288-2:2011 乘用车.自由控制性能.第2部分:转向脉冲开环试验方法

This part of ISO 17288 specifies a procedure for determining the free control stability of a passenger car as defined in ISO 3833, by measurement of the transient behaviour following steering pulse input, starting from a straight-ahead, steady-state status. NOTE The open loop manoeuvre specified in this part of ISO 17288 is not representative of normal driving conditions, but is useful for obtaining a measure of vehicle transient behaviour.

Passenger cars - Free-steer behaviour - Part 2: Steering-pulse open-loop test method

BS ISO 11026:2010 重型商用车辆和公共汽车.转动稳定性检测方法.合拢弯道检测

Heavy commercial vehicles and buses. Test method for roll stability. Closing-curve test

JIS D 0801 ERRATUM 1:2010 勘误表

ERRATUM

ISO 12214:2010 道路车辆.汽车手控装置的转向指示器

This International Standard gives design recommendations and requirements for the direction-of-motion of hand controls found in passenger, multipurpose and commercial vehicles, and buses.

Road vehicles - Direction-of-motion stereotypes for automotive hand controls

KS R ISO 12214:2009 道路车辆.汽车手控装置的转向指示器

이 표준은 승용차, 다목적 상용차 및 버스에 설치된 수동 제어 장치의 작동 방향에 대한 디

Road vehicles-Direction-of-motion stereotypes for automotive hand controls

ISO 26402:2008 农业车辆.农业挂车的转向操纵系统.半悬挂式挂车的铰接转向装置的接触面

Agricultural vehicles - Steering systems for agricultural trailers - Interface for articulated steering device of semi-mounted trailers

SAE J2208-2007 自动驾驶用停车标准

To provide a Recommended Practice for validating the function and integrity of an automatic transmission park mechanism with its associated control system and environment. To define the requirments for parking mechanisms of automatic transmissions through evaluation in designated usages. Encompasses all vehicle usages, up to maximum GVW, with all available production released axle rations and tire sizes.

Park Standard for Automatic Transmissions

SAE J1890-2007 再生产的液压驱动的齿条和齿轮式转向机构的性能保证

In order to insure that the remanufactured and/or rebuilt steering gear has and maintains the reliability and performance associated with a new OEM steering gear, it is essential that the following procedures be followed: if in-house engineering capabilities are limited, it may be necessary to consult with an outside laboratory to insure all testing methods used meet with the requirements outlined in this paper.

Performance Assurance of Remanufactured, Hydraulically-Operated Rack and Pinion Steering Gears

NF R10-034:2007 客车.车辆转弯时的停车反作用力.开环试验方法

Passenger cars - Power-off reactions of a vehicle in a turn - Open-loop test method.

NF R10-033:2007 客车.转向制动.开环试验方法

Passenger cars - Braking in a turn - Open-loop test method.

SAE J2672-2004 降低手控力的助力转向和助力转向备用系统

This Information Report relates to a special class of automotive adaptive equipment which consists of modifications to the hydraulic control mechanism of Original Equipment Manufacturer (OEM) power steering systems provided as original equipment on personally licensed vehicles. These modifications are generically called "reduced effort power steering". The purpose of the modification is to lower the amount of driver effort required to operate the steering system. Retention of reliability, ease of use for physically disabled drivers and maintainability are of primary concern. Because this is an Information Report, the numerical values for performance measurements presented in this report and in the accompanying Test Procedure, while based upon the best knowledge available at the time, have not been validated by a testing of the Test Procedure.

Reduced Effort Power Steering and Power Steering Backup Systems

SAE J2588-2004 转向遥控系统

This SAE Information Report establishes a uniform procedure for assuring the manufactured quality, installed utility and performance of automotive remote steering controls other than those provided by the vehicle manufacturer (OEM). These products are intended to provide driving capability to persons with physical disabilities. The adaptive modifications seek to compensate for lost or reduced function in the extremities of the driver with a disability. Remote steering controls are designed to provide a steering input device alternative to the OEM steering wheel that either reduces the required input force, changes the required range of motion or changes the location of the steering control or any combination of the above. These controls supplement by power, other than by the driver?s own muscular efforts, the force output of the driver with a disability. Because this is an Information Report, the numerical values for performance measurements presented in this report and in the accompanying Test Procedure, while based upon the best knowledge available at the time, have not been validated by a testing of the Test Procedure.

Remote Steering Control Systems

QC/T 703-2004 汽车转向盘聚氨酯泡沫包覆层技术条件

本标准规定了汽车转向盘聚氨酯泡沫包覆层要求、试验方法和检验规则。 　　本标准适用于用模塑浇注发泡法一次成型的整体汽车转向盘聚氨酯泡沫包覆层，包覆层主体材料有聚醚—聚氨酯泡沫构成，不含全卤化含氟含氯烃类的发泡剂。

Specification of PU foam wrap layer for auto steering-wheel

QC/T 704-2004 汽车转向盘聚氨酯泡沫包覆层整体硬度试验方法

本标准规定了以聚氨酯泡沫为包覆层材料的汽车转向盘硬度的试验方法。 　　本标准适用于各种乘用车和商用车转向盘的聚氨酯泡沫包覆层材料。

Test method of PU foam wrap layer integer hardness for auto steering-wheel

NF R14-707-1:2003 道路车辆.关于运输信息和控制系统的司机视野特性的测量.第1部分: 定义和参数

Road vehicles - Measurement of driver visual behaviour with respect to transport information and control systems - Part 1 : definitions and parameters.

NF R14-705:2003 道路车辆.运输信息和控制系统的人类工程学特性.对话管理原则和一致性程序

Road vehicles - Ergonomic aspects of transport information and control systems - Dialogue management principles and compliance procedures.

ISO/TS 20825:2003 道路车辆.拉杆连接件、拉杆眼、转盘主销、钩连接件和环形眼.使用中的机械连接件的磨损极限值

This Technical Specification specifies the maximum allowable wear and the limit dimensions of worn components of in-use mechanical couplings, which, when respected, will ensure the safe operation on the road of heavy commercial vehicles fitted with such couplings. It is applicable to the following standardized mechanical couplings: — 40 mm and 50 mm drawbar couplings (see ISO 3584); — 40 mm and 50 mm drawbar eyes (see ISO 8755 and ISO 1102); — 50 mm and 90 mm fifth wheel kingpins (see ISO 337 and ISO 4086); — hook couplings and toroidal eyes (see ECE Regulation No. 55).

Road vehicles - Drawbar couplings, drawbar eyes, fifth wheel kingpins, hook couplings and toroidal eyes - Wear limits for in-use mechanical couplings

SAE J297-2002 工业设备的操作控制

This SAE Standard is intended to improve operator efficiency and convenience by providing guidelines for the uniformity of location and direction of motion of operator controls used on industrial wheeled equipment. The controls covered are those centrally located at the operator's normal position.

Operator Controls on Industrial Equipment