T35 车用电子、电气设备与仪表综合 标准查询与下载
共找到 361 条与 车用电子、电气设备与仪表综合 相关的标准，共 25 页
本标准规定了B型板簧螺母的型式与尺寸、技术条件。 本标准适用于螺纹规格为M4～M10，机械性能等级为8.8及其以下的螺栓配合使用的汽车用B型板簧螺母。
B type spring nuts
- ICS
- 43.040
- CCS
- T35
- 发布
- 2011-12-20
- 实施
- 2012-07-01
This part of ISO 13209 specifies a standardized, tester-independent, XML-based data exchange format for the documentation and formal description of diagnostic test sequences. The format serves to support the requirements of transferring diagnostic-test-sequence logic between electronic system suppliers, vehicle manufacturers and service dealerships/repair shops. This part of ISO 13209 provides an introduction to the rationale behind ISO 13209. It gives an overview of the document set and structure along with the use case definitions and a common set of resources (definitions, references) for use by all subsequent parts.
Road vehicles - Open Test sequence eXchange format (OTX) - Part 1: General information and use cases
- ICS
- 43.020
- CCS
- T35
- 发布
- 2011-11
- 实施
Road vehicles - Functional safety - Part 4: Product development at the system level
- ICS
- 43.040.01;43.040.10
- CCS
- T35
- 发布
- 2011-11
- 实施
Road vehicles - Functional safety - Part 5: Product development at the hardware level
- ICS
- 43.040.01;43.040.10
- CCS
- T35
- 发布
- 2011-11
- 实施
Road vehicles - Functional safety - Part 7: Production and operation
- ICS
- 43.040.01;43.040.10
- CCS
- T35
- 发布
- 2011-11
- 实施
This part of ISO 15765 gives an overview of the structure and the partitioning of ISO 15765, and shows the relationships between the different parts. It also defines the diagnostic network architecture. The terminology defined in this part of ISO 15765 is common for all diagnostic networks and is used throughout all parts of ISO 15765. The diagnostic communication over controller area network (DoCAN) protocol supports the standardized service primitive interface as specified in ISO 14229-2.
Road vehicles - Diagnostic communication over Controller Area Network (DoCAN) - Part 1: General information and use case definition
- ICS
- 43.040.15
- CCS
- T35
- 发布
- 2011-10
- 实施
本标准规定了柴油车排气后处理装置的术语和定义、试验条件和试验方法。 本标准适用于柴油车排气后处理装置,包括氧化型催化转化器(DOC)、颗粒过滤器(DPF)、选择性催化还原装置(SCR)。由以上基本后处理装置单元衍生组合的系统参照本标准执行。
Measurement methods for diesel vehicle aftertreatment devices
- ICS
- 43.040.10
- CCS
- T35
- 发布
- 2010-08-16
- 实施
- 2010-12-01
本标准规定了汽车散热器总成技术要求、试验方法、检验规则和标识、包装、运输、储存。 本标准适用于汽车散热器。
Automobile radiator
- ICS
- 43.040
- CCS
- T35
- 发布
- 2010-08-16
- 实施
- 2010-12-01
本标准规定了汽车空-空中冷器总成(以下简称中冷器)的技术要求、试验方法、检验规则和标志、包装、运输、储存。
Automobile air-to-air charge air cooler technical specification
- ICS
- 43.040.10
- CCS
- T35
- 发布
- 2010-08-16
- 实施
- 2010-12-01
本标准规定了自卸汽车液压缸产品型号的构成及主参数选择,一般要求,性能要求,试验方法,检验规则,产品标牌、使用说明书和附件、包装、运输、储存。 本标准适用于以液压油为工作介质的自卸汽车举升系统用单作用活塞式液压缸、双作用单活塞杆液压缸、单作用柱塞式液压缸、单作用伸缩式套筒液压缸、末级双作用伸缩式套筒液压缸(以下简称液压缸)。
Technical specification of hydraulic cylinder for dump truck
- ICS
- 43.040
- CCS
- T35
- 发布
- 2010-08-16
- 实施
- 2010-12-01
本标准规定了自卸汽车液压系统(以下简称液压系统)的要求,检验规则,标志、使用说明书和随机文件、包装、运输、储存。 本标准适用于自卸汽车的液压系统,其他专用汽车液压系统参照执行。
The technical-specification of tipper hydraulic system
- ICS
- 43.040.10
- CCS
- T35
- 发布
- 2010-08-16
- 实施
- 2010-12-01
本标准规定了桥梁检测车的术语和定义、基本规格、要求、试验方法、检验规则和标志、使用说明书及随车文件、运输、储存。 本标准适用于采用已定型汽车底盘改装的折叠式、桁架式、混合式桥梁检测车(以下简称桥检车)。其他型式和有特殊要求的桥梁检测车可参照本标准执行。
Bridge inspection vehicle
- ICS
- 43.040.10
- CCS
- T35
- 发布
- 2010-08-16
- 实施
- 2010-12-01
本标准根据专用汽车的结构和技术特性,规定了专用汽车的类别和代码。 本标准适用于GB／T 3730.1-2001中2.1.1.11、2.1.2.1.8和GB／T 17350-2009所规定的车辆。
Classification and code of special purpose vehicle
- ICS
- 43.040.01
- CCS
- T35
- 发布
- 2010-08-16
- 实施
- 2010-12-01
本标准规定了汽车水暖式汽车尾气加热器的技术要求、试验方法、检验规则和标志、包装、运输、储存。 本标准适用于汽车水暖式汽车尾气加热器(以下简称尾气加热器)。
Vehicle exhaust gas-operated water heating radiator
- ICS
- 43.040.10
- CCS
- T35
- 发布
- 2010-08-16
- 实施
- 2010-12-01
本标准规定了乘用车座椅用电动滑轨的技术要求、试验方法、检验规则和标志、包装、运输、储存。 本标准适用于M类车辆的座椅用电动滑轨，M和M类车辆的座椅用电动滑轨可参照执行。
Technical specification of power slide for passenger car seat
- ICS
- 43.040.10
- CCS
- T35
- 发布
- 2010-08-16
- 实施
- 2010-12-01
This part of ISO 8820 specifies fuse-links with tabs (blade-type) Type C (medium), Type E (high current) and Type F (miniature) for use in road vehicles. It establishes, for these fuse-link types, the rated current, test procedures, performance requirements and dimensions. This part of ISO 8820 is applicable for fuse-links with a rated voltage of 32 V or 58 V, a current rating of u 100 A and a breaking capacity of 1 000 A intended for use in road vehicles. This part of ISO 8820 is intended to be used in conjunction with ISO 8820-1 and ISO 8820-2. The numbering of its clauses corresponds to that of ISO 8820-1, whose requirements are applicable, except where modified by requirements particular to this part of ISO 8820.
Road vehicles - Fuse-links - Part 3: Fuse-links with tabs (blade type) Type C (medium), Type E (high current) and Type F (miniature)
- ICS
- 43.040.10
- CCS
- T35
- 发布
- 2010-06
- 实施
Automotive parts -- Degrees of protection (IP Code) -- Protection of electrical equipment against foreign objects, water and access
- ICS
- 43.040.10
- CCS
- T35
- 发布
- 2010-02-22
- 实施
이 표준은 특정한 디자인과 기술적인 특징에 따라 나타낸 도로 차량의 타입과 연관된 용어를
Road vehicles－Types－Terms and definitions
- ICS
- 01.040.43;43.020
- CCS
- T35
- 发布
- 2009-12-15
- 实施
- 2009-12-15
标准规定了汽车用轮胎气压表的分类、要求、试验方法、检验规则、标志、包装、运输及贮存、保管。 本标准适用于测量汽车用轮胎气压表。
Tyre air-pressure gauge for automobile
- ICS
- 43.040.10
- CCS
- T35
- 发布
- 2009-11-17
- 实施
- 2010-04-01
