T82 传动和制动系统 标准查询与下载

QC/T 449-2010 保温车、冷藏车技术条件及试验方法

本标准规定了保温车、冷藏车的技术要求、试验方法、检验规则和标志、使用说明书及随车文件、运输、储存。 本标准适用于采用定型汽车底盘改装的保温车、冷藏车和保温半挂车、冷藏半挂车(以下统称保温车、冷藏车,本标准中的冷藏车系指机械制冷式冷藏车),其他型式的保温车、冷藏车亦可参照执行。

Technical conditions and test methods of insulated and refrigerated vehicles

QC/T 222-2010 自卸汽车通用技术条件

本标准规定了自卸汽车的要求,检验规则,标志、使用说明书和随车文件、运输、储存。 本标准适用于定型汽车二类底盘、以液压倾卸的自卸汽车(包括后卸自卸汽车、侧卸自卸汽车和三面自卸汽车)。 其他类型的具有自卸功能的机动车参照执行。

General specifications for tipper

BS ISO 8709:2010 轻便摩托车.制动器和制动系统.试验和测量方法

Mopeds - Brakes and brake systems - Tests and measurement methods

BS ISO 8710:2010 摩托车.车闸和制动系统.试验和测量方法

Motorcycles - Brakes and brake systems - Tests and measurement methods

ISO 8710:2010 摩托车.刹车和制动系统.试验和测量方法

This International Standard specifies tests and measurement methods for service brake systems and, where applicable, associated parking brake systems of two-wheeled motorcycles (3-3), motorcycles with sidecar (3-4) and tricycles (3-5) which are intended for use on public roads, in order to establish uniform worldwide test procedures for braking systems.

Motorcycles - Brakes and brake systems - Tests and measurement methods

ISO 8709:2010 轻便摩托车.制动和制动系统.试验和测量方法

This International Standard specifies tests and measurement methods for service brake systems and, where applicable, associated parking brake systems of two-wheeled mopeds (3-1) and three-wheeled mopeds (3-2) which are intended for use on public roads, in order to establish uniform worldwide test procedures for braking systems. This International Standard does not cover mopeds which: ? have a maximum speed of less than 25 km/h; ? are equipped for disabled riders. This International Standard sets out the following types of tests: ? dynamic tests: ? dry stop test (single brake control actuated); ? wet brake test; ? parking brake system test; ? power-assisted brake system failure test.

Mopeds - Brakes and brake systems - Tests and measurement methods

QC/T 818-2009 摩托车和轻便摩托车辐条式车轮

本标准规定了摩托车和轻便摩托车辐条式车轮的术语和定义、要求、试验方法、检验规则、标志、包装、运输及贮存。 本部分适用于摩托车和轻便摩托车辐条式车轮。

Spoke-wheels of motorcycles and mopeds

QC/T 232-2009 摩托车和轻便摩托车制动手柄强度要求及试验方法

本标准规定了摩托车和轻便摩托车制动手柄强度要求及试验方法。 本标准适用于摩托车制动手柄。

Strength requirements and test methods for brake handle of motorcycles and mopeds

QC/T 227.2-2009 摩托车和轻便摩托车制动片粘结剪切强度试验方法

本标准规定了摩托车和轻便摩托车制动片粘结剪切强度试验方法。本标准适用于摩托车鼓式制动器的制动蹄组件和盘式制动器的制动衬组件的粘结剪切强度试验。

Test methods of the adhesive bonding shearing strength of brake lining for motorcycles and mopeds

QC/T 227.1-2009 摩托车和轻便摩托车制动片摩擦性能试验方法

本标准规定了摩托车和轻便摩托车制动片摩擦性能试验对试片的要求、试验设备、试验程序及数据处理方法。 本标准适用于摩托车制动片摩擦性能试验。

Test methods of the friction perfamance of brake lining for motorcycles and mopeds

QC/T 71-2009 摩托车和轻便摩托车轮辋

本标准规定了摩托车和轻便摩托车轮辋的术语和定义、产品分类、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于用钢制或轻合金制的摩托车和轻便摩托车辐条式车轮用轮辋。 用钢制或轻合金制的摩托车和轻便摩托车辐板式车轮用轮辋亦可参照本标准。 本标准不适用于用铸造方法制造的轮辋。

Rims of motorcycles and mopeds

NF E26-115*NF ISO 10190:2008 摩托车链条.特性和试验方法

Motorcycle chains - Characteristics and test methods.

ISO 10190:2008 摩托车链条.特性和试验方法

This International Standard specifies the dimensions and mechanical properties of roller and bush chains (together with details of associated chain sprockets), in the range 6,35 mm to 19,05 mm pitch, for use in motorcycle applications. These chains are suitable for external drives (e.g. rear drives). It covers dimensions, tolerances, length measurement, preloading, minimum tensile strength and minimum dynamic strength.

Motorcycle chains — Characteristics and test methods

QC/T 800-2008 摩托车和轻便摩托车自动离合无级变速器性能台架试验方法

本标准规定了摩托车和轻便摩托车机械式自动离合无级变速器性能台架试验的试验设备、试验条件和试验方法。 本标准适用于摩托车和轻便摩托车的机械式自动离合无级变速器。

Method of bed testof continuously variable transmission for motorcycles and mopeds

SAE J1101-2007 摩托车的停车稳定性的测试用试验程序

Side stands and center stands are designed to support stationary two wheel motorcycles. This SAE Recommended Practice establishes procedures for determining parking surface loading and stability limits as follows: a. The footprint pressure exerted on a horizontal parking surface by the stand, b. The tilt angle of the parking surface at which tip-over occurs, and c. the tilt angle of the parking surface at which roll-off occurs.

Test Procedure for Parking Stability of Motorcycles

QC/T 781-2007 摩托车和轻便摩托车制动盘

本标准规定了摩托车和轻便摩托车制动盘（以下简称制动盘）的分类、要求、试验方法、检验规则及标志、包装、运输和储存。 本标准适用于摩托车和轻便摩托车用冲压成形的制动盘。其他形式的制动盘可参照使用。

Braking disc for motorcycles and mopeds

SANS 20060:2007 关于就驾驶员操纵的控制件，包括控制件的识别，信号装置和指示器方面批准两轮摩托车和轻便摩托车的统一规定

Applies to vehicles of categories L1 and L3 with regard to driver operated controls.

Uniform provisions concerning the approval of two-wheeled motor cycles and mopeds with regard to driver-operated controls including the identification of controls, tell-tales and indicators

QC/T 655-2005 摩托车和轻便摩托车制动器技术条件

本标准规定了摩托车和轻便摩托车制动器(以下简称制动器)总成及其部件的分类、要求、试验方法、检验规则、标志和包装。 本标准适用于摩托车和轻便摩托车制动器总成及其部件。

Specifications of brakes for motorcycles and mopeds

QC/T 654-2005 摩托车和轻便摩托车制动器台架试验方法

本标准规定了摩托车和轻便摩托车制动器总成制动性能的台架试验设备、试验条件、试验程序及方法。 本标准适用于摩托车和轻便摩托车制动器的总成。

Test methods of braking devices for motorcycles and mopeds

DB50/T 207-2005 摩托车及轻便摩托车自动离心式离合器（湿式）技术条件

本标准规定了摩托车及轻便摩托车自动离心式离合器（湿式）的分类、术语和定义、要求、试验方法、检验规则、判定规则和标志、包装、运输、贮存；本标准适用于摩托车和轻便摩托车用自动离心式离合器（湿式）及类似自动离心式离合器（湿式）。

Motorcycle and moped automatic centrifugal clutch (wet) technical specification