U47 舱室辅机 标准查询与下载

CB* 3346-1988 船用泵轴的变压力机械密封

本标准规定了船用泵轴的变压力机械密封的产品分类、技术要求、试验及方法、检验规则、包装及保证等。 本标准适用于流体压力变化范围0.01～3.3MPa，流体温度-20～80℃，工作转速不大于3600 r/min，公称直径25～72mm的潜艇及深潜器中立式舷外吸入泵旋转轴的变压力机械密封。也适用于输送压力大幅度波动变化液体的旋转机械的轴密封(串并联转换系统中的泵轴密封及串并联泵的轴密封)和潜艇及深潜器的侧推进轴及舵轴的密封。

Variable pressure mechanical seal of marine pump shaft

BS MA 105-3:1987 系列 3 船载驳船 通风系统主要配合尺寸规范

This International Standard specifies the principal mating dimensions of the ventilation system of shipborne barges, series 3.

Series 3 shipborne barges. Specification for principal mating dimensions for the ventilating system

CB* 3319-1987 船用溴化锂吸收式制冷机型式和基本参数

本标准规定以水蒸汽或热水为能源，溴化锂水溶液为吸收剂，水为制冷剂，制取船舶空气调节用冷水的船用溴化锂吸收式制冷机的型式和基本参数。

Types and basic parameters of marine lithium bromide absorption refrigerators

CB 1169-1986 油船惰性气体系统技术条件

本标准主要适用于设置在载运闪点低于60℃(闭环试验)的散装油船上以主、辅锅炉烟道气作气源的惰性气体系统。 也适用以惰性气体发生装置或装有废气后燃烧的装置作惰性气体源的系统。

Specifications for oil tanker inert gas system

CB* 3300.2-1986 船用滑油、淡水冷却器 技术条件

本标准适用于船用柴油机、汽轮机以及动力装置系统等的循环淡水或循环润滑油用的圆简直管型冷却器。冷却海水在冷却管内流动，被冷却介质在壳侧曲折流动。

Specifications for marine lubricating oil and fresh water coolers

CB* 3248-1985 船用制冷压力容器技术条件

 本标准适用于船舶运输冷藏货的制冷装置、采用以制冷剂R717(氨)R12和R22的钢制焊接压力容器及壳管式换热器(贮液器、冷凝器、蒸发器、中间冷却器……等)。对于船舶空调装置及小型伙食冷藏装置的制冷用钢制焊接压力容器及壳管式换热器亦可参照执行。 船用制冷压力容器除应符合本标准的规定外，还应符合图样要求，并且必须符合1983年《钢质海船入级与建造规范》的有关规定。 本标准不适用于下列各类容器： a． 其他标准规定的压力容器； b． 设计压力大于2.454MPa(25kgf/cm^(2))的压力容器，贮藏制冷剂的钢瓶； c． 壳体内径在160mm以下的容器； d． 容积V小于25L的容器。

Specifications for Marine Refrigerated Pressure Vessels

CB*/Z 330-1983 船舶空调系统设计方法

Air conditioning System's Design Method on Board Ships

CB 998-1982 CYF-1型臭氧发生器

CYF-1 type ozone generator

CB 1006-1982 小流量凝水泵

本标准适用于船舶海水淡化装置输送饱和凝水的单级离心泵。

Small flow condensate pump

ABS 24-1980 惰性气体观察系统及原料选择手册指南

This Manual is intended to provide information relative to the selection, maintenance, inspection and testing of materials for inert gas systems using flue gas derived from ships boilers.

Guidance Manual for Material Selection and Inspection of Inert Gas Systems

CB* 838-1978 手动艉轴滑油泵

本标准规定的手动艉轴滑油泵适用于各类船舶油润滑的艉轴系统。

Manual stern shaft oil pump

ISO 4567:1978 造船 游艇 废水接头

Shipbuilding; Yachts; Waste water fittings

NAVY MIL-P-17454 B INT AMD 2-1966 潜水的便携式的离心泵

This Interim Amendment is issued for use by the Naval Ship Engineering Center with Military Specification MIL-P- 174543, dated 10 March 1954 and Amendment- 1 thereto, dated 3 June 1960.

PUMP, CENTRIFUGAL, PORTABLE, SUBMERSIBLE

NAVY MIL-P-17454 B (1)-1960 潜水的便携式的离心泵

This amendment fwms a part of Military Spcdficatìon MIL-P-l7454B,10 Marah 1954, has been approiyed by the Departnwnt of Defense, and is mamìatory for we by the Departincuts of the Aimp, the Navy and the Air Farce.

PUMP, CENTRIFUGAL, PORTABLE, SUBMERSIBLE

NAVY MIL-P-17454 B-1954 潜水的便携式的离心泵

Scope.-!lXs speci?cation eovers lightweight, portable, electric-motor driven centrifugal pumps capable of operating indefinitely under mater. They are used primarily for the purpose of unwatering flooded ship compartments

PUMP, CENTRIFUGAL, PORTABLE, SUBMERSIBLE

NAVY MIL-V-15765 A-1952 旋转真空泵(摄影用)

This specification covers a vacuum pump MILP-16789 - Preservation, Packagfor use with lithographic cameras. The pump - ins, Packing, and Marking of Pumps, shall be of the sliding vane, rotary pidon, Centrifugal, Cloue Coupled, Nüvg and positive dry vacuum type. '

VACUUM PUMP, ROTARY (FOR PHOTOGRAPHIC USE)

CBM 2208-1982 船用电动齿轮泵技术条件

Specifications for Marine Electric Gear Pumps

CBM 2209-1982 船用电动齿轮泵试验方法

Test methods for marine electric gear pumps

CBM 2218-1982 船用卧式自吸离心泵型式和基本参数

Types and basic parameters of marine horizontal self-priming centrifugal pumps

CBM 2219-1982 船用卧式自吸离心泵技术条件

Specifications for marine horizontal self-priming centrifugal pumps