共找到 225 条与 轴系设备 相关的标准,共 15 页
Surface ship mooring and sailing test procedures part 170: Steering gear test
Surface ship mooring and sailing test procedures part 43: adjustable pitch propeller device test
Mooring and sailing test procedures for surface warships Part 38: Constant current electric propulsion device test
Surface ship mooring and sailing test procedures part 168: Fin stabilizer device test
This SAE Standard specifies basic tolerances and dimension for inboard propeller-shaft ends, propeller hubs and keyways for shaft sizes 3/4 in (19 mm) through 8 in (203 mm).
Marine Propeller-Shaft Ends and Hubs
本规范规定了舰船用低碳钢轴系(含舵轴)锻件的冶炼、锻造、试验方法和检验规定等。 本规范适用于由钢锭(或锻坏)制造的成品直径不大于300mm的低磁钢轴系锻件的制造和验收。其他轴类锻件可对照执行。
Specification of low-magnetic steel forgings for ship shafting
Specifies the minimum level of requirements for construction, operation and installation of remote steering systems for all small inboard jet boats weighing less than 1 000 kg, excluding water scooters.
Small craft - Remote steering systems for inboard mini jet boats
本标准规定了船用整体式橡胶轴承(以下简称为“橡胶轴承”)的分类和结构、要求、试验方法、检验规则、标志等。 本标准适用于轴承内径为4.mm~200mm、比压不大于0.3MPa的水润滑(冷却水温度不超过60℃)橡胶轴承的设计、制造和验收。
Marine whole rubber bearing
本标准规定了船舶动力装置发动机输出轴与传动轴之间连接用的膜片联轴器、膜盘联轴器及鼓型齿联轴器(以下统称联轴器)的要求、试验方法、检验规则、标志、包装、运输和贮存等。 本标准适用于额定转速高于3000r/min、传递额定功率大于2000kW的联轴器的设计、制造和验收。
Flexible couplings for high power and speed engine of marine
이 규격은 지름이 0.80∼2.50 m인 선박용 나선형 프로펠러의 제작 허용값에 대하여 규
Ship screw propellers-Manufacturing tolerances-Part 2:Propellers of diameter between 0.80 and 2.50 m inclusive
? ??? ???? ???? ?? ?? ???? ???? ????? ???? ?? ? ??
Propulsion plants for ships-Part 2:Vocabulary for controllable-pitch propeller plants
이 규격은 자력 추진식 또는 추진 보조식 선박 및 이동식 해상 구조물과 같은 기타 선박의
Propulsion plants for ships-Part 1:Vocabulary for geometry of propellers
이 규격은 지름이 2.50 m를 초과하는 선박용 나선형 프로펠러의 제작 허용값에 대하여 규
Shipbuilding-Ship screw propellers-Manufacturing tolerances-Part 1:Propellers of diameter greater than 2.50 m
本指导性技术文件规定了中、低速柴油机直接传动、齿轮传动推进轴系校中的计算准备、校中状态、限制条件、校中计算模型、计算内容、施工要则、校中检验等要求。 本指导性技术文件适用于船舶推进轴系校中的计算、安装和检验。
Propulsion shaft alignment of ship
이 규격은 선박의 연료유 및 윤활유 관계에 사용하는 복식 기름 거르개(이하 거르개라 한다.
Ships duplex oil strainers
이 규격은 선박의 연료유 및 윤활유 관계에 사용하는 H형 기름 거르개(이하 기름 거르개라
Ships duplex oil strainers(H type)
이 규격은 선박에서 사용하는 0.6/1 kV 및 250 V 이하의 고무 절연 클로로프렌 시
Rubber insulated electrical chloroprene sheath cables for marine use
이 규격은 선박에 사용하는 거르개의 철망 사용 기준에 대하여 규정한다.
Application for wire gauze of oil strainer for marine use
이 규격은 선박의 기름, 물, 증기 등의 관 계통에 사용하는 거르개(이하 거르개라 한다.)
Shipbuilding-Application of strainers
本标准规定了内河船舶轴系中间轴承(以下简称中间轴承)产品的分类和基本型式、基本参数和产品标记、结构和主要尺寸、技术要求,验收,标志、包装、运输和贮存。 本标准适用于内河各类航行船舶,沿海船舶亦可参照采用。
The middle bearing for inlandwaterway ship shafting
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号