共找到 225 条与 轴系设备 相关的标准,共 15 页
この規格は,直径0.8m以上2.5m以下の船用プロペラの製作許容差について規定する。
Shipbuilding -- Ship screw propellers -- Manufacturing tolerances -- Part 2: Propellers of diameter between 0.80 and 2.50 m inclusive
? ??? ??? ?? ?? ?? ???? ???? ???? ??? ??? ????.
Distance pieces for ship's hull
MS19089A, dated 13 January 1982, is inactive for new design and is no longer used, except for replacement purposes.
BEARING, ROLLER, TAPERED, DOUBLE ROW OF ROLLERS, STEEP ANGLE, TWO SINGLE CONES, ONE DOUBLE CUP, NON ADJUSTABLE, TYPE 767 (TNA)
MS19088A, dated 13 January 1982, is inactive for new design and is no longer used, except for replacement purposes.
BEARING, ROLLER, TAPERED, DOUBLE ROW OF ROLLERS, NORMAL ANGLE, TWO SINGLE CONES, ONE DOUBLE CUP, NON ADJUSTABLE, TYPE 764 (TNA)
MS19087A, dated 13 January 1982, is inactive for new design and is no longer used, except for replacement purposes.
BEARING ROLLER, TAPERED DOUBLE ROW OF ROLLERS, STEEP ANGLE, TWO SINGLE CONES, ONE DOUBLE CUP, ADJUSTABLE, TYPE 763 (TDOS)
This practice provides the three principal methods of fitting chocks to marine machinery foundations to ensure that the machinery is free of vibration and perfectly aligned after installation. 3.1.1 The three principal methods of installing chocks described herein are as follows: 3.1.1.1 Type A—Epoxy-based resin, nonshrinking Chockfast Orange PR 610 TCF by Philadelphia Resin Corp., or equal, and 3.1.1.2 Type B—Two-piece wedge chocks. 3.1.1.3 Type C—Solid, one-piece fitted chocks.1.1 This practice covers the acceptable methods of fitting chocks to marine machinery foundations.1.2 The values stated in SI units shall be regarded as standard. The values in parentheses are for information only.1.3 This standard does not purport to address the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Practice for Installation Procedures for Fitting Chocks to Marine Machinery Foundations
1.1 This practice covers the acceptable methods of fitting chocks to marine machinery foundations. 1.2 The values stated in SI units shall be regarded as standard. The values in parentheses are for information only. 1.3 This standard does not purport to address the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Practice for Installation Procedures for Fitting Chocks to Marine Machinery Foundations
p>This practice provides the three principal methods of fitting chocks to marine machinery foundations to ensure that the machinery is free of vibration and perfectly aligned after installation. The three principal methods of installing chocks described herein are as follows: Type A—Epoxy-based resin, nonshrinking Chockfast Orange PR 610 TCF by Philadelphia Resin Corp., or equal, and Type B—Two-piece wedge chocks. Type C—Solid, one-piece fitted chocks.1.1 This practice covers the acceptable methods of fitting chocks to marine machinery foundations. 1.2 The values stated in SI units shall be regarded as standard. The values in parentheses are for information only. 1.3 This standard does not purport to address the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Practice for Installation Procedures for Fitting Chocks to Marine Machinery Foundations
Shipbuilding -- Fixing parts of small propellers
Ship intermediate shaft compartment stuffing box
Technical Requirements for Alignment of Propulsion Shafting of Inland Waterships
The basic diameter of the rubber seal ring of the ship stern shaft and sealing device is 130-280mm
Lubricating oil tank for stern shaft of inland ships
Ship stern shaft and sealing device J-type rubber sealing ring basic diameter 70-120mm
Ship stern shaft and sealing device thin sleeve bearing flanging rubber sealing system basic diameter 40-100mm
Corrigendum relates to the extension of the length of the threaded end of propeller shafts (table 1).
Small craft with inboard engine - Propeller shaft ends and bosses with 1:16 taper; Technical Corrigendum 1
本标准规定了螺旋桨诱导且作用在船体表面脉动压力测量数据的统一采集与表达方式。 本标准适用于以螺旋桨作为推进装置的水面舰船,民用船舶可参照执行。
Regulations for measurement of propeller pulsation pressure on surface ships
本标准规定了推拉软轴操纵装置的产品分类、技术要求、试验方法、检验规则、标志、包装和贮运。 本标准适用于软轴传递操纵力的船用机械遥控装置,其它机械遥控装置亦可参照采用。
Push-pull flexible shaft manipulation device
本标准规定了侧推装置安装及效用试验质量要求。 本标准适用于新建船舶的侧推装置。
Quality requirements for side thruster installation and performance test
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号