U50 船舶管路附件综合 标准查询与下载

NAVY MIL-S-24660 VALID NOTICE 1-1990 180度顶体撒水头

MIL-S-24660(SH), dated 10 October 1985 has been reviewed and determined to be valid for use in acquisition,

SPRINKLER HEAD, 180 DEGREES FULL CONE

DLA MIL-S-955 D-1988 (船上使用)淋浴头和装置

This specification covers shower heads and outfits for shipboard use.

SHOWER HEADS AND OUTFITS (SHIPBOARD USE)

KS V 7015-1986 船舶用管路系统的识别

이 규격은 선박에서 배관 계통내의 유체 종류의 식별을, 주로 색에 따라 표시하는 경우의 일

Identification of Piping Systems for Marine Use

ASTM F1006-86(2008) 船用管道装置用液滴分离器的标准规范

1.1 This specification covers the minimum requirements for the pressure-temperature rating, testing, and making of pressure-containing vessels for entrainment separators. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 The following safety hazards caveat pertains only to the test methods portion, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Entrainment Separators for Use in Marine Piping Applications

ASTM F1006-86(2004) 船用管道装置用液滴分离器

1.1 This specification covers the minimum requirements for the pressure-temperature rating, testing, and making of pressure-containing vessels for entrainment separators. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. The following safety hazards caveat pertains only to the test methods portion, Section , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Entrainment Separators for Use in Marine Piping Applications

CB*/Z 344-1985 动力管路的流速

本标准规定船舶动力管路内介质(蒸汽、燃油、滑油、冷却水、压缩空气)的流速。 本标准是根据流体，包括蒸汽、乏汽、压缩空气、冷却水(包括海水)和油的性质，设备的种类和系统中各项阻力制定的曲线图(即流速范围)。见图1。

The flow rate of the power line

NAVY MIL-S-24660-1985 180度顶体撒水头

This specification covers 180 degree f u l l cone sprinkler heads. Sprinkler heads shall be for pendent or upright installation in overhead sprinkler systems.

SPRINKLER HEAD, 180 DEGREES FULL CONE

JIS F 7005:1984 船舶管道系统的识别

この規格は，船における配管系統内の流体の種類の識別を，主として色によって表示する場合の一般事項について規定する。

Identification of piping system on board ships

NAVY MIL-STD-22 D NOTICE 2-1984 焊缝设计

This standard covers welded jointdesigns for manual, semi-automatic, and automatic arc and gaswel ding processes for useon metals and weldments, as applicable, when invoked by a fabricatio-1 document such as NAVSEA 0900-LP-000-1000 or MIL-STD-278.

WELDED JOINT DESIGN

CB*/Z 324-1982 船舶管路附件修理技术条件

本标准适用于公称压力Pg≤250kgf/cm2、公称通径Dg≤500mm的水面船舶管路的阀门及其他附件的冷热交换器等附属装置的修理。 本标准不适用于通风系统之附件、连接在主、辅机和锅炉上的专用阀门及特殊用途的专用阀门的修理。

Technical conditions for repair of ship piping accessories

BS MA 94:1981 船舶管路系统用隔热规范

Requirements for the thermal insulation of marine piping systems in the temperature range -40C to +565C including diesel exhaust systems.

Specification for thermal insulation for marine piping systems

ISO 5571:1981 造船.通风系统设计图的识别颜色

Shipbuilding; Identification colours for schemes for ventilation systems

CB* 250-1977 水和蒸汽管路材料及试验压力

本标准规定水管系、蒸汽管系的材料、连接方法和试验压力。

Water and steam piping materials and test pressures

UL 1105-1977 船用过滤器、净化器和分离器

Marine use filters, strainers and separators

BS MA 18:1973 船舶用咸水管路系统规范

Specifies materials, design, fabrication, installation, inspection and testing of salt water piping systems in ships, in which the design pressure in the pipes does not exceed 16 bar.

Specification for salt water piping systems in ships

DLA MS9301 REV A-1972 AMS 6322型钢锚杆机的0.625-18 UNJF-3A型六边六边单孔钻头黑色二极管

The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.

BOLT, MACHINE-STEEL, AMS 6322, BLACK OXIDE, DRILLED 1 HOLE, HEXAGON HEAD, .625-18 UNJF-3A

DLA MS9300 REV A-1972 AMS 6322型钢锚杆机的0.5625-18 UNJF-3A型六边单孔钻头黑色二极管

The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.

BOLT, MACHINE-STEEL AMS 6322, BLACK OXIDE, DRILLED, 1 HOLE, HEXAGON HEAD, .5625-18 UNJF-3A

DLA MS9287 REV A-1972 AMS 6322型钢锚杆机的0.4375-20 UNJF-3A型六边黑色二极管

The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.

BOLT, MACHINE-STEEL AMS 6322, BLACK OXIDE, HEXAGON HEAD, .4375-20 UNJF-3A

DLA MS9289 REV A-1972 AMS 6322型钢锚杆机的0.5625-18 UNJF-3A型六边黑色二极管

The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.

BOLT, MACHINE-STEEL AMS 6322, BLACK OXIDE, HEXAGON HEAD, .5625-18 UNJF-3A

DLA MS9290 REV A-1972 AMS 6322型钢锚杆机的0.624-18 UNJF-3A型六边黑色二极管

The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.

BOLT, MACHINE-STEEL AMS 6322, BLACK OXIDE, HEXAGON HEAD, .624-18 UNJF-3A