13.030.10;13.030.20 标准查询与下载

GB/T 38103-2019 含锂废料处理处置方法

Treatment and disposal method for lithium-containing waste materials

GB/T 33071-2016 含钴废料处理处置技术规范

本标准规定了含钴废料的分类、处理处置方法及环境保护与安全要求。 本标准适用于含钴废料的处理处置。

Technical specification for cobalt scrap treatment and disposal

HG/T 4840-2015 酮类物质泄漏的处理处置方法

本标准告知了酮类物质的理化性质和危害性，规定了发生酮类物质泄漏时的紧急措施、泄漏现场的处理方法和泄漏现场的处置方法。 本标准适用于GB 12268-2012列明的酮类物质在生产、贮存、使用、经营和运输等过程中发生泄漏时的处理、处置。

Treatment and disposal method for ketones spill

HG/T 4545-2013 氯氧化锆生产废弃物回收方法

本标准规定了碱法生产氯氧化锆过程中产生的废碱液和酸性硅渣的回收方法。本标准适用于碱法生产氯氧化锆过程中产生的废碱液和酸性硅渣的回收。

The recovery method of waste material produced in the process of zirconium oxychloride

DS/EN 15308:2008 废物表征 通过使用带电子捕获或质谱检测的毛细管气相色谱法测定固体废物中选定的多氯联苯（PCB）

This document specifies a method for quantitative determination of seven polychlorinated biphenyl congeners (PCB-28, PCB-52, PCB-101, PCB-118, PCB-138, PCB-153 and PCB-180) in solid waste using high-resolution gas chromatography with electron capture or mass spectrometric detection. The basic content of this standard is identical to that of the Horizontal PCB-standard and is therefore also applicable to soil, sludge and treated bio-waste. The detection and the quantification limits in this method are dependent on sample intake, the level of interferences as well as instrumental limitations. Under the conditions specified in this standard, minimum concentrat

Characterization of waste - Determination of selected polychlorinated biphenyls (PCB) in solid waste by using capillary gas chromatography with electron capture or mass spectrometric detection

DS/EN 15169:2007 废物表征 废物、污泥和沉积物中烧失量的测定

This European Standard specifies a method for the determination of the loss on ignition.This procedure is applicable to all kinds of waste, sludge and sediments.The loss on ignition is often used as an estimate for the content of non-volatile organic matter in waste, sludge and sediments. It should be noted that any content of elementary carbon and volatilisation of organic materials or chemical reactions by inorganic compounds, is included in the loss on ignition.

Characterization of waste - Determination of loss on ignition in waste, sludge and sediments

BS PD CEN/TR 15310-4:2006 废弃物的特性描述.废料的取样.第4部分:样品的包装、储存、保护、运输和交付规程导则

This Technical Report describes procedures for the packaging, preservation, short-term storage and transport of both solid and liquid waste samples, including paste-like substances and sludges. Where available and appropriate for field application, requirements for specific storage conditions and/or preservation methods should be selected from the chosen analytical standard and collaboration with the testing laboratory. NOTE 1 This Technical Report provides a shop shelf of example sampling techniques that can be selected to meet a wide range of sampling situations. For a specific situation one of the presented procedures may be appropriate. NOTE 2 The procedures listed in this Technical Report reflect current best practice, but these are not exhaustive and other procedures may be equally relevant.

Characterization of waste — Sampling of waste materials — Part 4: Guidance on procedures for sample packaging, storage, preservation, transport and delivery

BS PD CEN/TR 15310-5:2006 废弃物特性.废料的抽样.第5部分:关于确定取样计划程序的导则

This Technical Report provides guidance on process of defining of a Sampling Plan based on the objective of the testing programme. It specifically deals with the strategic decisions that are needed, based on the sampling objective. NOTE 1 Given the great variety of waste types, sampling situations and objectives, this Technical Report cannot provide definitive instructions that cover all scenarios. Instead, it discusses the basic statistical approach to be followed, and provides statistical tools that can be applied to determine the amount and type of sampling (e.g. number of samples and sample size) in any given situation to achieve results of adequate reliability (i.e. precision and confidence). NOTE 2 The document provides considerable detail on current best practice, but is not exhaustive. NOTE 3 To clarify the text, the document provides a number of worked examples.

Characterization of waste — Sampling of waste materials — Part 5: Guidance on the process of defining the sampling plan

BS PD CEN/TR 15310-1:2006 废弃物特性.废弃物材料取样.第1部分:多种条件下取样标准的选择和应用导则

This Technical Report discusses the statistical principles of sampling, and provides a number of statistical tools to assist in the design of testing programmes for application to sampling under various conditions. NOTE 1 Given the great variety of waste types, sampling situations and objectives, this Technical Report cannot provide definitive instructions that cover all scenarios. Instead, it discusses the basic statistical approach to be followed, and provides statistical tools that can be applied to determine the amount and type of sampling (e.g. number of samples and sample size) in any given situation to achieve results of adequate reliability (i.e. precision and confidence). NOTE 2 The document provides considerable detail on current best practice, but is not exhaustive. NOTE 3 To clarify the text, the document provides a number of worked examples.

Characterization of waste — Sampling of waste materials — Part 1: Guidance on selection and application of criteria for sampling under various conditions

BS PD CEN/TR 15310-2:2006 废弃物特性.废弃物材料取样.第2部分:采样技术指导

This Technical Report describes techniques for sampling liquid and granular waste material, including paste-like materials and sludges, found in a variety of locations. The Technical Report provides information to allow the selection and preparation of equipment and apparatus to be used in the sampling activity. NOTE 1 This Technical Report provides a shop shelf of example sampling techniques that can be selected to meet a wide range of sampling situations. For a specific situation one of the presented procedures may be appropriate. NOTE 2 The procedures listed in this Technical Report reflect current best practice, but these are not exhaustive and other procedures may be equally relevant.

Characterization of waste — Sampling of waste materials — Part 2: Guidance on sampling techniques

DIN EN 12457-3:2003 废弃物特性.浸析.颗粒废弃物和污泥浸析的一致性试验.第3部分:高固体含量的粒径小于4mm的材料在液体与固体比为 2 l/kg 和 8 l/kg 时的二级分批试验(有或无粒径缩减); 德文版本 EN 12457-3:2002

Characterization of waste - Leaching; Compliance test for leaching of granular waste materials and sludges - Part 3: Two stage batch test at a liquid to solid ratio of 2 l/kg and 8 l/kg for materials with high solid content with particle size below 4 mm (

DIN EN 12457-4:2003 废弃物的表征.浸析.颗粒废弃物和污泥浸析一致性试验.第4部分:粒径小于10mm的材料在液体、固体比为10 l/kg的一级分批试验(有或无有限粒径缩减)

This part of the European Standard specifies a compliance test providing information on leaching of granular wastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ratio of 10 l/kg dry matter. It applies to waste which has a particle size below 10 mm without or with limited size reduction. Note: In some cases, it could be useful to test the material with coarser particles up to 40 mm in diameter: This requires a larger amount for material and liquid.

Characterization of waste - Leaching; Compliance test for leaching of granular waste materials and sludges - Part 4: One stage batch test at a liquid to solid ratio of 10 l/kg for materials with particle size below 10 mm (without or with limited size redu

DIN EN 12457-1:2003 废弃物表征.浸析.颗粒废弃物和污泥浸析一致性试验.第1部分:粒径小于4mm的材料在液体、固体比为2 l/kg的一级分批试验(有或无粒径缩减)

Characterization of waste - Leaching; Compliance test for leaching of granular and sludges - Part 1: One stage batch test at a liquid to solid ration of 2 l/kg with particle size below 4 mm (without or with size reduction); German version EN 12457-1:2002

DIN EN 12457-2:2003 废弃物表征.浸析.颗粒废弃物和污泥浸析一致性试验.第2部分:粒径小于4mm的材料在液体、固体比为10 l/kg的一级分批试验(有或无粒径缩减)

This part of the European Standard specifies a compliance test providing information on leaching of granular wastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ratio of 10 l/kg dry matter. It applies to waste which has a particle size below 4 mm without or with size reduction. The test procedure specified in this Standard produces an eluate which shall subsequently be characterised physically and chemically according to appropriate standard methods.#,,#

Characterization of waste - Leaching; Compliance test for leaching of granular and sludges - Part 2: One stage batch test at a liquid to solid ratio of 10 l/kg with particle size below 4 mm (without or with size reduction); German version EN 12457-2:2002

BS EN 12457-2:2002 废弃物的特性.浸析.颗粒废弃物和污泥浸析的一致性试验.高固体含量和粒径小于4 mm的材料在液体,固体比为10 l/kg时的一级分批试验

This part of four European Standards specifies a compliance test providing information on leaching of granular wastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ratio of 10 l/kg dry matter. It applies to waste which has a particle size below 4 mm without or with size reduction (as specified in 4.3.2) This European Standard has been developed to investigate mainly inorganic constituents from wastes. It does not take into account the particular characteristics of non-polar organic constituents nor the consequences of microbiological processes in organic degradable wastes. The test procedure specified in this European Standard produces an eluate which shall subsequently be characterised physically and chemically according to appropriate standard methods. NOTE 1 This procedure cannot be applicable to materials with a water content or such a water affinity that a good mixing of the solid with the predetermined quantity of liquid is not achievable. NOTE 2 This procedure cannot be applicable to materials reacting with the leachant, leading, for example, to excessive gas emission, a solidifying effect or an excessive heat release. NOTE 3 By crushing the material, new surfaces are exposed which may lead to a change in leaching properties. This test cannot be used alone to determine the leaching behaviour of a waste, as specified in ENV 12920 . This European Standard does not address issues related to health and safety.

Characterisation of waste. Leaching. Compliance test for leaching of granular waste materials and sludges. One stage batch test at a liquid to solid ratio of 10 l/kg for materials with particle size below 4 mm (without or with size reduction)

BS EN 12457-4:2002 废弃物的特性.浸析.颗粒废弃物和污泥浸析的一致性试验.粒径小于10 mm材料在液体,固体比为10 l/kg时的一级分批试验

This part of four European Standards specifies a compliance test providing information on leaching of granular wastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ratio of 10 l/kg dry matter. It applies to waste which has a particle size below 10 mm without or with size reduction (as specified in 4.3.2) NOTE In some cases, it could be useful to test the material with coarser particles up to 40 mm in diameter. This requires a larger amount for material and liquid. In this particular case, particle size distribution related differences in leaching may be more pronounced than in the standard procedure. This European Standard has been developed to investigate mainly inorganic constituents from wastes. It does not take into account the particular characteristics of non-polar organic constituents nor the consequences of microbiological processes in organic degradable wastes. The test procedure specified in this European Standard produces an eluate which shall subsequently be characterised physically and chemically according to appropriate standard methods. NOTE 1 This procedure cannot be applicable to materials with a water content or such a water affinity that a good mixing of the solid with the predetermined quantity of liquid is not achievable. NOTE 2 This procedure cannot be applicable to materials reacting with the leachant, leading, for example, to excessive gas emission, a solidifying effect or an excessive heat release. NOTE 3 By crushing the material, new surfaces are exposed which may lead to a change in leaching properties. This test cannot be used alone to determine the leaching behaviour of a waste, as specified in ENV 12920. This European Standard does not address issues related to health and safety.

Characterisation of waste. Leaching. Compliance test for leaching of granular waste materials and sludges. One stage batch test at a liquid to solid ratio of 10 l/kg for materials with particle size below 10 mm (without or with size reduction)

BS EN 12457-1:2002 废弃物的特性.浸析.颗粒废弃物和污泥浸析的符合性试验.高固体含量和粒径小于4 mm的材料在液体,固体比为2 l/kg时的一级分批试验(有或无尺寸减小)

This part of four European Standards specifies a compliance test providing information on leaching of granular wastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ratio of 2 l/kg dry matter. It applies to waste which has a particle size below 4 mm without or with size reduction (as specified in 4.3.2) This European Standard has been developed to investigate mainly inorganic constituents from wastes. It does not take into account the particular characteristics of non-polar organic constituents nor the consequences of microbiological processes in organic degradable wastes. The test procedure specified in this European Standard produces an eluate which shall subsequently be characterised physically and chemically according to appropriate standard methods. This procedure is only applicable to waste material and sludges having a high solid content : the dry matter content ratio shall be at least higher than 33%. In addition, the necessary quantity of eluate shall be obtained to perform the physical and chemical characterisation of the eluate. Furthermore, the minimum dry matter content ratio shall be high enough to allow a sufficient mixing of the leachant and the test portion. NOTE 1 This procedure cannot be applicable to materials with a water content or such a water affinity that a good mixing of the solid with the predetermined quantity of liquid is not achievable. NOTE 2 This procedure cannot be applicable to materials reacting with the leachant, leading, for example, to excessive gas emission, a solidifying effect or an excessive heat release. NOTE 3 By crushing the material, new surfaces are exposed which may lead to a change in leaching properties. NOTE 4 In relation with the minimum dry matter content ratio required for obtaining enough eluate, the test portion specified in this European Standard of 175 gram dry matter results in a maximum volume of eluate of 175 ml if its dry matter content ratio is 50 %. When this part 1 is not applicable, the leaching test at L/S = 10 specified in part 2 can be performed. This test cannot be used alone to determine the leaching behaviour of a waste, as specified in ENV 12920. This European Standard does not address issues related to health and safety.

Characterisation of waste. Leaching. Compliance test for leaching of granular waste materials and sludges. One stage batch test at a liquid to solid ratio of 2 l/kg for materials with high solid content and with particle size below 4 mm (without or with s

EN 12457-4:2002 废弃物的特性.浸析.颗粒废弃物和污泥浸析的一致性试验.第4部分:粒径小于10mm 材料在液体,固体比为10l/kg时的一级分批试验(有或无有限粒径缩减)

This European Standard specifies a compliance test providing information on leaching of granular wastes and sludges underThe experimental conditions specified hereafter, and particularly a liquid to solid ratio of 10 l/kg dry matter. It applies to waste which has a particle size below 10 mm without or with size reduction (as specified in 4.3.2)

Characterisation of waste - Leaching; Compliance test for leaching of granular waste materials and sludges - Part 4: One stage batch test at a liquid to solid ratio of 10 l/kg for materials with particle size below 10 mm (without or with size reduction)

EN 12457-2:2002 废物特性.浸出.粒状废料和残渣浸出的符合性试验第2部分:在10 l/kg的液固比下对粒子尺寸小于4mm的(没有或有尺寸缩减)材料进行一级批量试验

This part of four European Standards specifies a compliance test providing information on leaching of granularwastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ratioof 10 I/kg dry matter. It applies to waste which has a particle size below 4 mm without or with size reduction (asspecified in 4.3.2)

Characterisation of waste - Leaching; Compliance test for leaching of granular waste materials and sludges - Part 2: One stage batch test at a liquid to solid ratio of 10 l/kg for material with particle size below 4 mm (without or with size reduction)

EN 12457-3:2002 废物特性.浸出.粒状废料和残渣浸出的符合性试验.第3部分:在2 l/kg和8 l/kg的液固比下对高固体含量和粒子尺寸小于4mm的(没有或有尺寸缩减)材料进行二级批量试验

This part of four European Standards specifies a compliance test providing information on leaching of granularwastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ratioof 2 I/kg dry matter in a first step and subsequently of 8 I/kg dry matter in a second step. It applies to waste whichhas a particle size below 4 mm without or with size reduction (as specified in 4.3.2)

Characterisation of waste - Leaching; Compliance test for leaching of granular waste materials and sludges - Part 3: Two stage batch test at a liquid to solid ratio of 2 l/kg and 8 l/kg for materials with high solid content and with particle size below 4