ASTM F1387-23
管道和卡套管机械连接配件性能标准规范

Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings

标准号

ASTM F1387-23

发布

2023年

发布单位

美国材料与试验协会

当前最新

ASTM F1387-23

 

 

引用标准

ANSI/ASQ Z1.4 ANSI/NCSL Z540 ASTM A1016/A1016M ASTM A106/A106M ASTM A108 ASTM A109/A109M ASTM A167 ASTM A182/A182M ASTM A213/A213M ASTM A234/A234M ASTM A249/A249M ASTM A262 ASTM A269/A269M ASTM A276/A276M ASTM A312/A312M ASTM A335/A335M ASTM A370 ASTM A380/A380M ASTM A403/A403M ASTM A450/A450M ASTM A479/A479M ASTM A53/A53M ASTM A530/A530M ASTM A564/A564M ASTM A576 ASTM A967 ASTM A999/A999M ASTM B111/B111M ASTM B117 ASTM B121/B121M ASTM B122/B122M ASTM B124/B124M ASTM B154 ASTM B16/B16M ASTM B164 ASTM B21/B21M ASTM B251/B251M ASTM B36/B36M ASTM B369/B369M ASTM B371/B371M ASTM B564 ASTM B633 ASTM B696 ASTM B75/B75M ASTM B766 ASTM B88 ASTM E1529 ASTM E511 ASTM E8/E8M MIL-C-15726 MIL-DTL-16232 MIL-DTL-18866 MIL-DTL-901 MIL-PRF-17331 MIL-PRF-7808 MIL-PRF-83282 MIL-STD-167-1 MIL-STD-1916 MIL-STD-777 MIL-STD-889 MIL-T-1368 MIL-T-16420 MIL-T-24107 MIL-T-8606 SAE 1010 SAE AMS-STD-753 SAE AMS2243 SAE AMS5643 SAE J514 SAE J515

适用范围

1.1 This specification establishes the performance characteristics required for mechanically attached fittings (MAFs) for use in piping and tubing systems. These fittings directly attach to pipe or tube by mechanical deformation of the pipe or tube or fitting, or a combination thereof, creating a seal and a restrained joint. The seal may be created via the mechanical deformation or created independently. Successful completion of the tests described constitutes completion of the technical portion of the qualification process. 1.2 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified in part or whole by the purchaser in the order. Unless otherwise specified, U.S. Navy contracts shall invoke the supplementary requirements in whole. 1.3 Unless specific MAF types are specified, the term “MAF” shall apply to all types described herein. 1.4 The tests specified in Section 13 and described in Annex A1 and the Supplementary Requirements Section are applicable only to ascertain the performance characteristics of MAFs. These tests are not intended for use in the evaluation of non-MAF products. 1.5 A fire performance test is specified in Supplementary Requirement S7. This test provides general guidelines to determine the responsiveness of MAFs when subjected to fire. This test should not be considered for use to evaluate non-MAF products. 1.6 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.7 The following safety hazards caveat applies only to the tests listed in Section 13 and the tests described in the Supplementary Requirements Section and the annexes of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F1387-23相似标准

推荐

谁引用了ASTM F1387-23 更多引用