GSO ISO 9611:2015由GSO 发布于 2015-09-03。
GSO ISO 9611:2015在国际标准分类中归属于: 17.140.20 机器和设备的噪声。
GSO ISO 9611:2015 声学 表征通过结构传输的声源特性与传导结构的声音发射相关 测量以灵活方式安装的设备通信中心的速度的最新版本是哪一版?
最新版本是 GSO ISO 9611:2015 。
1.1 General This International Standard specifies an approximate method of characterizing sources of structure-borne sound by the measurement of one-third-octave-band free velocity level spectra (or, if appropriate, octave-band velocity level spectra) on the supports or other connection points of machines mounted on resilient isolators. This structure-borne sound emission is considered with respect to the airborne or liquid-borne sound radiation of structures connected to the source under test. The results are only valid for applications in which the machine is mounted on sufficiently soft isolators on a sufficiently stiff and heavy foundation. NOTE 1 More conditions are given in annex H. A survey of the theoretical background is given in annex E. It is possible to satisfy the requirements for the test arrangement in almost any surroundings. Velocities measured at defined contact points give no complete description of structure-borne sound emission of the machinery. But, under specific conditions as described in this International Standard for resiliently mounted machinery, they give a subset of the source data required for a characterization. The results can be used a) to obtain data for technical specifications; b) for comparison with machines of similar type and size; and c) to obtain input data for computations on the transfer of structure-borne sound. 1.2 Frequency range The frequency range for which the method is applicable is limited by a low frequency f1 and an upper frequency f2. The low frequency limit f1 is set by the requirement that the supports vibrate freely; i.e. they are not affected by the isolators and the foundation structure on which the isolators are mounted. Annex A gives instructions on how to determine f1. The upper frequency limit f2 is determined by assuming that the supports behave as point sources of structure-borne sound. Annex B gives guidelines for the determination of f2. NOTES 2 For many machines, isolators can be selected which provide a frequency f1 between 20 Hz and 40 Hz. 3 Many machines have such a structure that f2 has a value between 1 kHz and 4 kHz. 1.3 Type of noise This International Standard applies to steady noise. 1.4 Degrees of freedom The procedures are described for all six components of the velocity: three orthogonal translational velocities and three orthogonal angular velocities. If it can be shown that, for a specific machine and a specific application, fewer components are sufficient to characterize the source, then it is permissible to reduce the number of measured components (see annex F). 1.5 Types of connection point The procedures in this International Standard are described for the main supports of a machine. The method is, however, applicable to other mounting faces at resilient elements such as the flange for a flexible coupling in the shaft of a diesel engine or the connection with pipes. In such cases, the methods for the determination of f1 and f2 (see annexes A and B) can be adapted to the unique conditions that apply.
如果把回声探测仪作相应的修改,安放于海底,使它向海面发射声脉冲,就可以测量波高和周期等,并从波高平均值的变化,获得潮位的变化规律。若把换能器安装于船舷外侧,也可测出波浪的要素。利用随海流运动的散射体的回波会出现多普勒频移的特性,可制成多普勒海流计,它可以不破坏流场而测量瞬时的低速海流。根据声波通过固定距离的传输时间和声速成比例的关系,可制成声速计,它能实时地测量海水的声速。...
然而,对大多数操作人员和管理人员而言,了解技术差异及其在野外环境的意义将有助于作出明智的选择,同样关系到设备操作、数据质量保障和未来的决策。本技术说明旨在从实践的角度阐明某些重要的技术差异。声学多普勒流速测量系统采用多普勒频移的物理原理来测量水流速度。多普勒原理指出了,如果声源相对于接收器运动,则接收器处的声音频率会与发射频率相偏移。...
众所周知,在机械工程与土木工程领域里,振动特性的测量一直存在着各种问题和挑战。虽然某些振动源自器件或部件本身,但由于外力或设计的容差造成的非正常振动则会导致器件或部件的功能性损坏。因此,振动特性的测量和分析是鉴别和确认机器、部件的质量特性及工作状态的重要测量手段。对于比较大型的被测物体通常可以安装加速度传感器,利用加速度传感器的电荷输出信号实现加速度-速度-位移的相关测量。...
针对不同的变电站要求,可根据传感器供电方式以及安装位置的不同,考虑安装方便的因素,选择相匹配的传感器。 6 结束语 实践证明物联网技术能够应用在钢铁厂电弧炉分布式温度采集系统中,由 PIC16F648A 单片机控制的测温节点,Atmega128a单片机控制的中心节点,和基于ZigBee技术的无线传输模块 QRF0600的无线测温系统具备测温准确、组网灵活、抗干扰能力强、性能稳定等特点。...
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号