SAE AS 7928/7-1999
175℃总导体温度用I型,1级,环形舌片,非绝缘,铜,压接,终端接线,铜,压接,导体接线端子

Terminal Lug and Splices, Conductor, Crimp Style, Copper, Terminal Lug, Crimp Style, Copper, Uninsulated, Ring Tongue Type I, Class 1 for 175 Degrees C Total Conductor Temperature FSC 5940; Should Be Used Instead of MIL-T-7928/7, Which Was Cancelled on 3

SAE AS 7928/7-1999 发布历史

Terminal Lug and Splices, Conductor, Crimp Style, Copper, Terminal Lug, Crimp Style, Copper, Uninsulated, Ring Tongue Type I, Class 1 for 175 Degrees C Total Conductor Temperature FSC 5940; Should Be Used Instead of MIL-T-7928/7, Which Was Cancelled on 3THE COMPLETE REQUIREMENTS FOR PROCURING THE SPLICE DESCRIBED HEREIN SHALL CONSIST OF THISDOCUMENT AND THE LATEST ISSUE OF SPECIFICATION MIL-T-7928. MIL-T-7928/5 IS NOT FOR NAVY USE. FORNAVY USE, USE MIL-S-81824 SPLICE.TABLE IREQUIREMENTS:1. MIN CABLE INSULATION SUPPORT: .060 FOR DASH 1 AND 2.094 FOR DASH 3, 4 AND 52. MATERIAL: COPPER (SEE ACQUISITION SPECIFICATION) OR COPPER ALLOY. MATERIAL SHALL HAVEADEQUATE ELECTRICAL CONDUCTIVITY AND SHALL BE SUFFICIENTLY STRONG TO RESIST CRACKINGAFTER FORMING AND CRIMPING.3. INSULATING SLEEVE: SEE ACQUISITION SPECIFICATION.4. FINISH: METAL, TIN PLATED: SEE ACQUISITION SPECIFICATION.5. DIMENSION B TO BE DETERMINED AS THE AVERAGE OF TWO DIAMETERS MEASURED AT RIGHT ANGLES.6. THE INSPECTION WINDOW AND LOCATOR SHALL PROVIDE A POSITIVE MEANS OF POSITIONING SPLICE INTHE APPLICABLE CRIMPTING TOOL AND PROVIDE VISIBLE INSPECTION OF STRIPPED WIRE ENDS.7. CRIMPING TOOLS: CRIMPING TOOLS FOR THE MIL-T-7928/5 SPLICES SHALL BE AS SPECIFIED BELOW.8. INSULATION SUPPORT AND WIRE BARREL MAY BE MULTIPLE PIECE CONSTRUCTION. CONTOUR MAY VARYFROM THAT SHOWN, WITHIN SPECIFIED DIMENSIONS, BUT WIRE LEAD-IN TO WIRE BARREL SHALL BEPROVIDED.9. QUALIFICATION: FOR QUALIFICATION, SPLICES SHALL BE TESTED WITH ANYONE OF THE FOLLOWINGWIRES: MIL-W-22759/1, 9 OR 11 OR MIL-W-81381/7.10. PART NUMBER: CONSISTS OF THE LETTER “M”, THE BASIC NUMBER OF THIS SPECIFICATION SHEET, AND ADASH NUMBER TAKEN FROM TABLE I.EXAMPLE: M7928/5-1 SPLICE FOR 26-24 WIRE RANGE.11. MIL-T-7928/5, UPON ISSUANCE OF A QPL FOR MIL-T-7928/5 SUPERSEDES MIL-T-7928/3 FOR PROCUREMENTAND NEW DESIGN. EXISTING STOCK OF M7928/3-2, -3 AND -4 ARE INTERCHANGEABLE WITH M7928/5-3, -4AND -5 AND MAY BE USED UNTIL EXHAUSTED. EXISTING STOCK OF M7928/3-1 SHOULD BE SCRAPPEDSINCE NO QPL HAS BEEN ESTABLISHED. AS REPLACEMENT, USE THE FOLLOWING EQUIVALENT DASH12. FLATTENING OF INSULATION SLEEVE TO FORM LOCATOR MAY CAUSE THE SLEEVE TO EXCEED THEE DIMENSION BY .050 MAX IN THE LOCATOR AREA FOR THE -1 THROUGH -4 AND .060 FOR THE -5.

SAE AS 7928/7-1999由美国机动车工程师协会 US-SAE 发布于 1999-04-01。

SAE AS 7928/7-1999 在中国标准分类中归属于: L24 安装、接线连接件，在国际标准分类中归属于: 49.060 航空航天用电气设备和系统。

SAE AS 7928/7-1999的历代版本如下：

• 1999年04月01日 SAE AS 7928/7-1999 175℃总导体温度用I型,1级,环形舌片,非绝缘,铜,压接,终端接线,铜,压接,导体接线端子

SAE AS 7928/7-1999 175℃总导体温度用I型,1级,环形舌片,非绝缘,铜,压接,终端接线,铜,压接,导体接线端子 于 2014-01-03 变更为 SAE AS 7928/7A-2014 175℃总导体温度用I型,1级,环形舌片,非绝缘,铜,压接,终端接线,铜,压接,导体接线端子。

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 SAE AS 7928/7-1999 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

SAE AS 7928/7-1999

发布日期

1999年04月01日

实施日期

废止日期

无

中国标准分类号

L24

国际标准分类号

49.060

发布单位

US-SAE

代替标准

SAE AS 7928/7A-2014

适用范围

Terminal Lug and Splices, Conductor, Crimp Style, Copper, Terminal Lug, Crimp Style, Copper, Uninsulated, Ring Tongue Type I, Class 1 for 175 Degrees C Total Conductor Temperature FSC 5940; Should Be Used Instead of MIL-T-7928/7, Which Was Cancelled on 3THE COMPLETE REQUIREMENTS FOR PROCURING THE SPLICE DESCRIBED HEREIN SHALL CONSIST OF THISDOCUMENT AND THE LATEST ISSUE OF SPECIFICATION MIL-T-7928. MIL-T-7928/5 IS NOT FOR NAVY USE. FORNAVY USE, USE MIL-S-81824 SPLICE.TABLE IREQUIREMENTS:1. MIN CABLE INSULATION SUPPORT: .060 FOR DASH 1 AND 2.094 FOR DASH 3, 4 AND 52. MATERIAL: COPPER (SEE ACQUISITION SPECIFICATION) OR COPPER ALLOY. MATERIAL SHALL HAVEADEQUATE ELECTRICAL CONDUCTIVITY AND SHALL BE SUFFICIENTLY STRONG TO RESIST CRACKINGAFTER FORMING AND CRIMPING.3. INSULATING SLEEVE: SEE ACQUISITION SPECIFICATION.4. FINISH: METAL, TIN PLATED: SEE ACQUISITION SPECIFICATION.5. DIMENSION B TO BE DETERMINED AS THE AVERAGE OF TWO DIAMETERS MEASURED AT RIGHT ANGLES.6. THE INSPECTION WINDOW AND LOCATOR SHALL PROVIDE A POSITIVE MEANS OF POSITIONING SPLICE INTHE APPLICABLE CRIMPTING TOOL AND PROVIDE VISIBLE INSPECTION OF STRIPPED WIRE ENDS.7. CRIMPING TOOLS: CRIMPING TOOLS FOR THE MIL-T-7928/5 SPLICES SHALL BE AS SPECIFIED BELOW.8. INSULATION SUPPORT AND WIRE BARREL MAY BE MULTIPLE PIECE CONSTRUCTION. CONTOUR MAY VARYFROM THAT SHOWN, WITHIN SPECIFIED DIMENSIONS, BUT WIRE LEAD-IN TO WIRE BARREL SHALL BEPROVIDED.9. QUALIFICATION: FOR QUALIFICATION, SPLICES SHALL BE TESTED WITH ANYONE OF THE FOLLOWINGWIRES: MIL-W-22759/1, 9 OR 11 OR MIL-W-81381/7.10. PART NUMBER: CONSISTS OF THE LETTER “M”, THE BASIC NUMBER OF THIS SPECIFICATION SHEET, AND ADASH NUMBER TAKEN FROM TABLE I.EXAMPLE: M7928/5-1 SPLICE FOR 26-24 WIRE RANGE.11. MIL-T-7928/5, UPON ISSUANCE OF A QPL FOR MIL-T-7928/5 SUPERSEDES MIL-T-7928/3 FOR PROCUREMENTAND NEW DESIGN. EXISTING STOCK OF M7928/3-2, -3 AND -4 ARE INTERCHANGEABLE WITH M7928/5-3, -4AND -5 AND MAY BE USED UNTIL EXHAUSTED. EXISTING STOCK OF M7928/3-1 SHOULD BE SCRAPPEDSINCE NO QPL HAS BEEN ESTABLISHED. AS REPLACEMENT, USE THE FOLLOWING EQUIVALENT DASH12. FLATTENING OF INSULATION SLEEVE TO FORM LOCATOR MAY CAUSE THE SLEEVE TO EXCEED THEE DIMENSION BY .050 MAX IN THE LOCATOR AREA FOR THE -1 THROUGH -4 AND .060 FOR THE -5.

SAE AS 7928/7-1999系列标准

谁引用了SAE AS 7928/7-1999 更多引用