SAE AS7928/7-1999
175℃总导体温度用I型,1级,环形舌片,非绝缘,铜,压接,终端接线,铜,压接,导体接线端子

Terminal Lug and Splices, Conductor, Crimp Style, Copper, Terminal Lug, Crimp Style, Copper, Uninsulated, Ring Tongue Type I, Class 1 for 175 Degrees C Total Conductor Temperature FSC 5940; Should Be Used Instead of MIL-T-7928/7, Which Was Cancelled on 3

作废

标准号

SAE AS7928/7-1999

发布

1999年

发布单位

美国机动车工程师协会

替代标准

SAE AS7928/7-2011

当前最新

SAE AS7928/7B-2024

 

 

适用范围

Terminal Lug and Splices, Conductor, Crimp Style, Copper, Terminal Lug, Crimp Style, Copper, Uninsulated, Ring Tongue Type I, Class 1 for 175 Degrees C Total Conductor Temperature FSC 5940; Should Be Used Instead of MIL-T-7928/7, Which Was Cancelled on 3THE COMPLETE REQUIREMENTS FOR PROCURING THE SPLICE DESCRIBED HEREIN SHALL CONSIST OF THISDOCUMENT AND THE LATEST ISSUE OF SPECIFICATION MIL-T-7928. MIL-T-7928/5 IS NOT FOR NAVY USE. FORNAVY USE, USE MIL-S-81824 SPLICE.TABLE IREQUIREMENTS:1. MIN CABLE INSULATION SUPPORT: .060 FOR DASH 1 AND 2.094 FOR DASH 3, 4 AND 52. MATERIAL: COPPER (SEE ACQUISITION SPECIFICATION) OR COPPER ALLOY. MATERIAL SHALL HAVEADEQUATE ELECTRICAL CONDUCTIVITY AND SHALL BE SUFFICIENTLY STRONG TO RESIST CRACKINGAFTER FORMING AND CRIMPING.3. INSULATING SLEEVE: SEE ACQUISITION SPECIFICATION.4. FINISH: METAL, TIN PLATED: SEE ACQUISITION SPECIFICATION.5. DIMENSION B TO BE DETERMINED AS THE AVERAGE OF TWO DIAMETERS MEASURED AT RIGHT ANGLES.6. THE INSPECTION WINDOW AND LOCATOR SHALL PROVIDE A POSITIVE MEANS OF POSITIONING SPLICE INTHE APPLICABLE CRIMPTING TOOL AND PROVIDE VISIBLE INSPECTION OF STRIPPED WIRE ENDS.7. CRIMPING TOOLS: CRIMPING TOOLS FOR THE MIL-T-7928/5 SPLICES SHALL BE AS SPECIFIED BELOW.8. INSULATION SUPPORT AND WIRE BARREL MAY BE MULTIPLE PIECE CONSTRUCTION. CONTOUR MAY VARYFROM THAT SHOWN, WITHIN SPECIFIED DIMENSIONS, BUT WIRE LEAD-IN TO WIRE BARREL SHALL BEPROVIDED.9. QUALIFICATION: FOR QUALIFICATION, SPLICES SHALL BE TESTED WITH ANYONE OF THE FOLLOWINGWIRES: MIL-W-22759/1, 9 OR 11 OR MIL-W-81381/7.10. PART NUMBER: CONSISTS OF THE LETTER “M”, THE BASIC NUMBER OF THIS SPECIFICATION SHEET, AND ADASH NUMBER TAKEN FROM TABLE I.EXAMPLE: M7928/5-1 SPLICE FOR 26-24 WIRE RANGE.11. MIL-T-7928/5, UPON ISSUANCE OF A QPL FOR MIL-T-7928/5 SUPERSEDES MIL-T-7928/3 FOR PROCUREMENTAND NEW DESIGN. EXISTING STOCK OF M7928/3-2, -3 AND -4 ARE INTERCHANGEABLE WITH M7928/5-3, -4AND -5 AND MAY BE USED UNTIL EXHAUSTED. EXISTING STOCK OF M7928/3-1 SHOULD BE SCRAPPEDSINCE NO QPL HAS BEEN ESTABLISHED. AS REPLACEMENT, USE THE FOLLOWING EQUIVALENT DASH12. FLATTENING OF INSULATION SLEEVE TO FORM LOCATOR MAY CAUSE THE SLEEVE TO EXCEED THEE DIMENSION BY .050 MAX IN THE LOCATOR AREA FOR THE -1 THROUGH -4 AND .060 FOR THE -5.

SAE AS7928/7-1999相似标准

推荐

SAE AS7928/7-1999系列标准