13.230 防爆 标准查询与下载

JB/T 11736-2014 镁合金压铸件精整机加工通风除尘安全规范

本标准规定了镁合金压铸件精整机加工通风除尘的术语和定义、个体防护、场地安全、生产设备安全、通风除尘装置安全、精整机加工安全、灭火与安全管理等安全规范。本标准适用于镁合金压铸件精整机加工场地的设计、生产与管理。

The ventilation and dust removal safety specification of magnesium alloy die casting in final finishing and machining process

GA/T 1156-2014 涉爆现场处置规范

本标准规定了涉爆现场的处置原则、一般处置流程与措施。本标准适用于爆炸物现场、持爆现场的处置工作。

Specifications for disposal of explosives and explosion scene

ASTM E1515-14 可燃尘埃最低爆炸浓度的标准试验方法

5.1 This test method provides a procedure for performing laboratory tests to evaluate relative deflagration parameters of dusts. 5.2 The MEC as measured by this test method provides a relative measure of the concentration of a dust cloud necessary for an explosion. 5.3 Since the MEC as measured by this test method may vary with the uniformity of the dust dispersion, energy of the ignitor, and propagation criteria, the MEC should be considered a relative rather than absolute measurement. 5.4 If too weak an ignition source is used, the measured MEC would be higher than the “true” value. This is an ignitability limit rather than a flammability limit, and the test could be described as “underdriven.” Ideally, the ignition energy is increased until the measured MEC is independent of ignition energy. However, at some point the ignition energy may become too strong for the size of the test chamber, and the system becomes “overdriven.” When the ignitor flame becomes too large relative to the chamber volume, a test could appear to result in an explosion, while it is actually just dust burning in the ignitor flame with no real propagation beyond the ignitor. 5.5 The recommended ignition source for measuring the MEC of dusts in 20-L chambers is a 2500 or 5000 J pyrotechnic ignitor.4 Measuring the MEC at both ignition energies will provide information on the possible overdriving of the system.5 To evaluate the effect of possible overdriving in a 20-L chamber, comparison tests may also be made in a larger chamber, such as a 1 m3-chamber. 5.6 If a dust ignites with a 5000 J ignitor but not with a 2500 J ignitor in a 20-L chamber, this may be an overdriven system.5 In this case, it is recommended that the dust be tested with a 108201;000 J ignitor in a larger chamber, such as a 1 m3-chamber, to determine if it is actually explosible. 5.7 The values obtained by this test method are specific to the sample tested (particularly the particle size distribution) and the method used and are not to be considered intrinsic material constants. 1.1 This test method covers the determination of the minimum concentration of a dust-air mixture that will propagate a deflagration in a near-spherical closed vessel of 20 L or greater volume. Note 1: The minimum explosible concentration (MEC) is also referred to as the lower explosibility limit (LEL) or lean flammability limit (LFL). 1.2 Data obtained from this test method provide a relative measure of the deflagration characteristics of dust clouds. 1.3 This test method should ......

Standard Test Method for Minimum Explosible Concentration of Combustible Dusts

DB31/ 753-2013 危险场所电气防爆安全检测作业规范

本标准规定了危险场所电气防爆安全检测的基本要求、检测项目及其技术要求以及检测方法。 本标准适用于危险场所电气防爆安全检测。 本标准不适用于下列环境： --矿井井下； --炸药的制造和加工场所； --利用电能进行生产并与生产工艺过程直接关联的电解、电镀等电气装置区域； --蓄电池室； --存储、使用强氧化剂及自燃物质的场所； --水、陆、空交通运输工具及海上油井平台。

Operation code for safety inspection of electrical installations in hazardous areas

SH 3009-2013 石油化工可燃性气体排放系统设计规范

本规范规定了石油化工可燃性气体排放系统的设计要求。本规范适用于石油化工企业可燃性气体排放系统新建、扩建和改建工程的设计。

Design specification for combustible gas discharge system in petrochemical industry

AQ 4230-2013 粮食平房仓粉尘防爆安全规范

本标准规定了粮食平房仓粉尘防爆安全的基本要求。本标准适用于储存原粮、成品粮的粮食平房仓的新建、扩建、维修、改建工程的设计、施工、生产和管理全过程。

Safety specification for the protection of dust explosion for grain storehouse

AQ 4229-2013 粮食立筒仓粉尘防爆安全规范

本标准规定了粮食立筒仓粉尘防爆的基本要求。本标准适用于粮食立筒仓的新建、扩建、改建工程的设计、施工、生产、维修和管理全过程。

Safety specification for the protection of dust explosion for grain silos

AQ 4231-2013 散粮码头爆炸性粉尘环境施工及装卸设备维修安全规范

本标准规定了散粮码头爆炸性粉尘环境施工及装卸设备维修安全的基本要求。本标准适用于散粮码头在爆炸性粉尘产生、积聚环境下施工和装卸设备的维修。

Safety specification for construction and handling equipment maintenance of explosive dust environment in bulk grain port

AQ 4232-2013 塑料生产系统粉尘防爆规范

本标准规定了塑料生产系统粉尘防爆的技术要求。本标准适用于:以烯烃类气体为原料,主要工艺过程为经聚合反应得到塑料粉末料、经造粒得到塑料颗粒料粉体的生产系统;以塑料、合成聚合物粉末或颗粒料为原料,通过熔融与注塑等工艺生产与加工塑料用品的生产系统,包括废旧塑料回收处理与加工生产系统。本标准不适用于塑料粉末喷涂工艺过程。

Safety specification for dust explosion protection and prevention in plastic processing system

VDI 2263 Blatt 7.1-2013 粉尘火灾和粉尘爆炸危险性评估防护措施喷涂干燥一体化设备防火防爆实例

The guideline gives practical advice and possible solutions for the protection against fire and explosions in spray dryers. It describes the state of the art regarding the level of development of advanced processes, facilities or modes of operation that asures the practical suitability of a measure to protect the health and safety of employees. The guideline applies to measures for explosion protection in spray dryers, where flammable dust/air mixtures, steam/air mixtures or hybrid mixtures are present of may develop at normal use. This guideline gives both manufacturers and operators information for carrying out risk assessments and protective measures in the form of examples. The guideline requires the knowledge of the guideline VDI 2263 Part 7.

Dust fires and dust explosions - Hazards - assessment - protective measures - Fire and explosion protection in spraying and drying integrated equipment - Examples

ANSI/UL 60079-0-2013 爆炸环境的安全性标准.第0部分:设备的一般要求

Standard for Safety for Explosive Atmospheres - Part 0: Equipment - General Requirements

ANSI/NFPA 69-2013 防爆系统标准

Standard on Explosion Prevention Systems

ANSI/UL 60079-11a-2013 爆炸性环境的安全性标准.第11部分:由本质安全型"i"保护的设备(提案日期 2013年1月18日)

Standard for Safety for Explosive Atmospheres - Part 11: Equipment Protection by Intrinsic Safety i (Proposal Ballot dated 01-18-13)

ANSI/UL 60079-15-2013 爆炸性气体环境的安全性标准.第15部分:"n"防护型电气设备保护(提案投票日期 2011年12月16日)

Standard for Safety for Explosive Atmospheres - Part 15: Equipment Protection by Type of Protection n (Proposal ballot dated 12/16/11)

GOST ISO/DIS 80079-37-2013 爆炸性气体环境. 第37部分. 爆炸性环境用非电气设备. 保护施工安全?c?, 点火源控制?b?以及液体浸透?k?的非电气型

Explosive atmospheres. Part 37. Non-electrical eguipment for explosive atmospheres. Non electrical type of protection constructional safety ?c?, control of ignition source ?b?, liquid immersion ?k?

GOST 32407-2013 爆炸性气体环境. 第36部分. 爆炸性环境用非电气设备. 基本方法和要求

Explosive atmospheres. Part 36. Non-electrical equipment for use in explosive atmospheres. Basic method and requirements

ANSI/UL 60079-11-2013 爆炸性环境的安全性标准.第11部分:由本质安全型"i"保护的设备(提案投票日期 2012年6月29日)

Standard for Safety for Explosive Atmospheres - Part 11: Equipment Protection by Intrinsic Safety i (Proposal Ballot dated 06-29-12)

LST EN 1839-2012 气体和蒸气爆炸极限的测定

Determination of explosion limits of gases and vapours

LST EN 14491-2012 粉尘爆炸泄爆保护系统

Dust explosion venting protective systems

AQ 4228-2012 木材加工系统粉尘防爆安全规范

本标准规定了工业生产中木材及木制品、人造板、木粉的加工处理系统中产生的木质及其他纤维质材料的粉尘的防爆安全要求。 本标准适用于木材加工厂、人造板厂、家具厂、木粉厂以及其他行业中的木工车间。 本标准不适用于以木粉为原料加工制作火药及烟花爆竹类产品的场所。

Safety code for dust explosion prevention in wood processing systems